Search Results

In-cylinder spray imaging by Mie scattering has been taken with frame rates up to 27,000 fps, along with high speed video photography of chemiluminescence and soot thermal radiation. Spectroscopic measurements have confirmed the presence of OH*, CH* and C2* emissions lines, and their magnitude relative compared to soot radiation. Filtering for CH* has been used with both the high speed video and a Photo-Multiplier Tube (PMT). The PMT signals have been found to correlate with the rate of heat release derived from in-cylinder pressure measurements. A high power photographic strobe has been used to illuminate the fuel spray. Images show that the fuel spray can strike the ground strap of the spark plug, break up, and a fuel cloud then drifts over and under the strap through the spark plug gap. Tests have conducted at two different spark plug orientations using a single spark strategy.

Particulate emissions from gasoline direct injection (GDI) engines continue to be a topic of substantial research interest. Forthcoming regulation both in the USA and the EU will further reduce their emission and drive innovation. Substantial research effort is spent undertaking experiments to understand, characterize, and research particle number (PN) emissions from engines and vehicles. Recent advances in computing power, data storage, and understanding of artificial intelligence algorithms now mean that these are becoming an important tool in engine research. In this work a random forest (RF) algorithm is used for the prediction of PN emissions from a highly boosted (up to 32 bar BMEP) GDI engine. Particle size, concentration, and the accumulation mode geometric standard deviation (GSD) are all predicted by the model. The results are analysed and an in depth study on parameter importance is carried out.

With the introduction in Europe of drive cycles such as RDE and WLTC, transient emissions prediction is more challenging than before for passenger car applications. Transient predictions are used in the calibration optimization process to determine the cumulative cycle emissions for the purpose of meeting objectives and constraints. Predicting emissions such as soot accurately is the most difficult area, because soot emissions rise very steeply during certain transients. The method described in this paper is an evolution of prediction using a steady state global model. A dynamic model can provide the instantaneous prediction of boost and EGR that a static model cannot. Meanwhile, a static model is more accurate for steady state engine emissions. Combining these two model types allows more accurate prediction of emissions against time. A global dynamic model combines a dynamic model of the engine air path with a static DoE (Design of Experiment) emission model.

An engine configuration has a significant influence on the sound quality from the powertrain. Whilst the fundamental order content can be readily apparent from the firing order over the engine, or bank of a V engine, some characteristics and how the engine design can influence them requires some more specific investigation. Understanding, on a fundamental level, the aspects of the engine design which influence these characteristics is critical to allow more detailed analysis and development work to be focused appropriately. The configuration of a Boxer engine gives a distinctive sound characteristic producing a unique sound compared to an In-Line configuration. Depending on the application it may be desirable to enhance or subdue some of these characteristics.

Requirements for reducing powertrain NVH drives the selection of low piston skirt to liner clearances contradicting the requirement to maintain larger skirt clearances for minimizing engine friction. Whilst this clearance trade-off between low friction and low NVH is fundamental, piston design features have a significant effect on where the trade-off curve sits on the friction/NVH map. Design features can therefore be viewed not by either friction or NVH improvement measures but a shift in the friction-NVH trade off curve. Specifically, some piston design features which may be targeted at reducing friction can be viewed as either a friction benefit for similar NVH or an NVH improvement for similar friction levels. The ability to realistically quantify the effect of the design changes on NVH is therefore critical to determining what design changes to recommend, the direction of the piston design being highly sensitive to the process by which the impact on NVH is assessed.

The introduction of transient test cycles and the focus on real world driving emissions has increased the importance of ensuring the NOx and soot emissions are controlled during transient manoeuvres. At the same time, there is a drive to reduce the number of calibration variables used by engine control strategies to reduce development effort and costs. In this paper, a control orientated combustion model, [1], and model predictive control strategy, [2], that were developed in simulation and reported in earlier papers, are applied to a Diesel engine and demonstrated in a test vehicle. The paper describes how the control approach developed in simulation was implemented in embedded hardware, using an FPGA to accelerate the emissions calculations. The development of the predictive controller includes the application of a simplified optimisation algorithm to enable a real-time calculation in the test vehicle.

In-cylinder temperature measurements are vital for the validation of gasoline engine modelling and useful in their own right for explaining differences in engine performance. The underlying chemical reactions in combustion are highly sensitive to temperature and affect emissions of both NOx and particulate matter. The two techniques described here are complementary, and can be used for insights into the quality of mixture preparation by measurement of the in-cylinder temperature distribution during the compression stroke. The influence of fuel composition on in-cylinder mixture temperatures can also be resolved. Laser Induced Grating Spectroscopy (LIGS) provides point temperature measurements with a pressure dependent precision in the range 0.1 to 1.0 % when the gas composition is well characterized and homogeneous; as the pressure increases the precision improves.

Since previous publications, Ricardo have continued to investigate the development of advanced after-treatment technologies through model based system simulation using an integrated model based development (IMBD) approach. This paper presents the results of the evaluation of after-treatment systems and management strategies for a range of diesel passenger cars. The targets of this study are applicable to Real Driving Emissions (RDE) legislation, but now targeting emissions levels beyond Euro 6d. The work was carried out as part of the EC Horizon 2020 co-funded REWARD (Real World Advanced technologies foR Diesel engines) project. Owing to the wide variation in feed-gas properties expected over an RDE cycle, the results seen for current production system architectures such as Lean NOX traps (LNT) or actively dosed Selective Catalytic Reduction (aSCR) systems highlight the challenge to adhere to emissions limitations for RDE legislation whilst fulfilling stringent CO2 targets.

In this study, the role of turbulence-chemistry interaction in diesel spray auto-ignition, flame stabilization and end of injection phenomena is investigated under engine relevant “Spray A” conditions. A recently developed diesel spray combustion modeling approach, Conditional Source-term Estimation (CSE-FGM), is coupled with Reynolds-averaged Navier-Stokes simulation (RANS) framework to study the details of spray combustion. The detailed chemistry mechanism is included through the Flamelet Generated Manifold (FGM) method. Both unsteady and steady flamelet solutions are included in the manifold to account for the auto-ignition process and the subsequent flame propagation in a diesel spray. Conditionally averaged chemical source terms are closed by the conditional scalars obtained in the CSE routine. Both non-reacting and reacting spray jets are computed over a wide range of Engine Combustion Network (ECN) diesel. “Spray A” conditions.

This study looked into the application of active thermal coatings on the surfaces of the combustion chamber as a method of improving the thermal efficiency of internal combustion engines. The active thermal coating was applied to a production aluminium piston and its performance was compared against a reference aluminium piston on a single-cylinder diesel engine. The two pistons were tested over a wide range of speed/load conditions and the effects of EGR and combustion phasing on engine performance and tailpipe emissions were also investigated. A detailed energy balance approach was employed to study the thermal behaviour of the active thermal coating. In general, improvements in indicated specific fuel consumption were not statistically significant for the coated piston over the whole test matrix. Mean exhaust temperature showed a marginal increase with the coated piston of up to 6 °C.

A Range-Extended Electric Vehicle (REEV) usually has an auxiliary power source that can provide additional range when the main Rechargeable Energy Storage System (RESS) runs out. The range extender can be a fuel cell, a gas turbine, or an Internal Combustion Engine (ICE) bolted to a generator. Sizing the powertrain for a REEV is primarily to investigate the relationship between the capacity of the main RESS and the power rating of the range extender. Worldwide harmonized Light vehicles Test Procedures (WLTP) introduced a Utility Factor (UF) which is a curve used to calculate the weighted test results for the Off-Vehicle Charging-Hybrid Electric Vehicle (OVC-HEV) from the measured Charge Depleting (CD) mode range result, and the Charge Sustaining (CS) mode Fuel Consumption (FC). Therefore, the RESS capacity, the range extender power rating, the control strategy, and the UF are the key factors affecting the weighted FC of a REEV on the test cycle.

Models for the convective heat transfer from the combustion gases to the walls inside a spark ignition engine are an important keystone in the simulation tools which are being developed to aid engine optimization. The existing models have, however, been cited to be inaccurate for hydrogen, one of the alternative fuels currently investigated. One possible explanation for this inaccuracy is that the models do not adequately capture the effect of the gas properties. These have never been varied in a wide range because air and ‘classical’ fossil fuels have similar values, but they are significantly different in the case of hydrogen. As a first step towards a fuel independent heat transfer model, we have investigated the effect of the gas properties on the heat flux in a spark ignition engine.

Engine efficiency and optimization are key aspects for automotive manufacturers. Lamborghini has particularly focus attention for reduction of time to market building up a synergic approach for new component's development using simulation, Know-how experiences, engine engineering expertise and experimental validation. In particular to reach the best results in the shortest time it is used, in the preliminary stage of development, a massive support of simulation analysis. In the Lamborghini approach analysis and simulation has become key aspects during concept and development of timing drives. This type of activity is used to support the development of better chain timing drives focusing on improving durability, lower friction, less noise and reduced cost in less time than conventional trial and processes. Even during the concept design phase it is useful to use a mathematical model to calculate dynamic forces and motions of a chain drive.

Spray guided Direct Injection Gasoline Engines are a key enabler to reducing CO2 emissions and improving the fuel economy of light duty vehicles. Particulate emissions from these engines have been shown to be lower than from first generation direct injection gasoline engines, but they may still be significantly higher than port fuel injected engines due to the reduced time available for mixture preparation and increased incidence of fuel impingement on the piston crown and combustion chamber surfaces. These factors are particularly severe in the period following a cold start. Both nuclei and accumulation mode particle size and number concentration were measured using a Cambustion differential mobility spectrometer. These data are reported for different coolant temperature intervals during the warm-up period. The bulk composition was determined using thermo-gravimetric analysis, and PM mass fractions are given for different volatility ranges and for elemental carbon.

Particulate Emissions from Homogeneous Charge Compression Ignition (HCCI) combustion are routinely assumed to be negligible. It is shown here that this is not the case when HCCI combustion is implemented in a direct injection gasoline engine. The conditions needed to sustain HCCI operation were realized using the negative valve overlap method for trapping high levels of residual exhaust gases in the cylinder. Measurements of emitted particle number concentration and electrical mobility diameter were made with a Cambustion DMS500 over the HCCI operating range possible with this hardware. Emissions of oxides of nitrogen, carbon monoxide and unburned hydrocarbons were also measured. These data are presented and compared with similar measurements made under conventional spark ignition (SI) operation in the same engine. Under both SI and HCCI operation, a significant accumulation mode was detected with particle equivalent diameters between 80 and 100 nm.

The blending of oxygenated compounds with gasoline is projected to increase because oxygenate fuels can be produced renewably, and because their high octane rating allows them to be used in substitution of the aromatic fraction in gasoline. Blending oxygenates with gasoline changes the fuels' properties and can have a profound affect on the distillation curve, both of which are known to affect engine-out emissions. In this work, the effect of blending methanol and ethanol with gasoline on unburned hydrocarbon and particulate emissions is experimentally determined in a spray guided direct injection engine. Particulate number concentration and size distribution were measured using a Cambustion DMS500. These data are presented for different air fuel ratios, loads, ignition timings and injection timings. In addition, the ASTM D86 distillation curve was modeled using the binary activity coefficients method for the fuel blends used in the experiments.

The 2/4SIGHT engine concept is based on a novel design of combustion system, which makes use of an electric-hydraulic valvetrain and advanced control technologies, enabling automatically controlled dynamic switching of the engine between two- and four-stroke operations. This concept has the potential to improve fuel consumption by up to 30% compared to a conventional gasoline engine. A 3 cylinder GDI engine with two stage boosting system and electro-hydraulic valvetrain is the main application for this project, with 6 cylinder application being studied in simulation. The design of a Control System poses several challenges due to the simultaneous introduction of several innovations such as advanced boost system, electro-hydraulic valvetrain system and two/four stroke operating mode. In order to develop and optimise the design of the control system, an integrated simulation environment has been developed.

A new method for predicting the piston slap noise has been developed. Although using conventional methods, piston slap noise was estimated by using kinetic energy or the vibration of the cylinder liner using the piston secondary motion simulation, predictive accuracy was low and it lacked in reliability. In this paper the distortion of the cylinder liner at the low temperature, the dynamic stiffness of the piston and the cylinder block, and an oil film model enhancement were taken into consideration. Furthermore, comparison with the measured data of piston motions proved that prediction of a high-precision liner vibration is possible. And it proved that the relative change of the cylinder liner vibration and the subjective evaluation had high correlation with the measurement results of a real engine. As a result, piston slap noise prediction of practical sufficient accuracy was attained.

Planar Laser-Induced Fluorescence has been widely accepted and applied to measurements of fuel concentration distributions in IC engines. The need for such measurements has increased with the introduction of Direct Injection (DI) gasoline engines, where it is critical to understand the influence of mixture inhomogeneity on ignition and subsequent combustion, and in particular the implications for cyclic variability. The apparent simplicity of PLIF has led to misunderstanding of the technique when applied to quantitative measurements of fuel distributions. This paper presents a series of engineering methods for optimizing, calibrating and referencing, which together demonstrate a quantitative measure of fuel concentration with an absolute accuracy of 10%. PLIF is widely used with single component fuels as carriers for the fluorescent tracers.

Increasing biodiesel content in mineral diesel is being promoted considerably for road transportation in Europe. With positive benefits in terms of net CO2 emissions, biofuels with compatible properties to those of conventional diesel are increasingly being used in combustion engines. In comparison to standard diesel fuel, the near zero sulphur content and low levels of aromatic compounds in biodiesel fuel can have a profound effect not only on combustion characteristics but on engine-out emissions as well. This paper presents analysis of particulate matter (PM) emissions from a turbo-charged, common rail direct injection (DI) V6 Jaguar engine operating with an RME (rapeseed methyl ester) biodiesel blended with ultra low sulphur diesel (ULSD) fuel (B30 - 30% of RME by volume). Three different engine load and speed conditions were selected for the test and no modifications were made to the engine hardware or engine management system (EMS) calibration.