Search Results

In order to investigate the effects of split injection on emission formation and engine performance, experiments were carried out using a heavy duty single cylinder diesel engine. Split injections with varied dwell time and start of injection were investigated and compared with single injection cases. In order to isolate the effect of the selected parameters, other variables were kept constant. In this investigation no EGR was used. The engine was equipped with a common rail injection system with a piezo-electric injector. To interpret the observed phenomena, engine CFD simulations using the KIVA-3V code were also made. The results show that reductions in NOx emissions and brake specific fuel consumption were achieved for short dwell times whereas they both were increased when the dwell time was prolonged. No EGR was used so the soot levels were already very low in the cases of single injections.

2-stage supercharging applied to HSDI Diesel engines is a promising solution for enhancing rated power, low end torque, transient response and hence the launch characteristics of a vehicle. However, a trade-off is required to match some conflicting issues, i.e. overall dimensions, cost, emissions control and performance. The outcome strongly depends on the specific constraints and goals of the project. In the paper, reference is made to 2.8L, 4 cylinder in-line unit produced by VM Motori (Cento, Italy), equipped by a standard variable geometry turbocharger. A 1D thermo-fluid-dynamic model of the Euro V version of the engine was built and calibrated against experiments at the dynamometer bench, at both full and partial load.

The paper presents the development of a novel approach to the solution of detailed chemistry in internal combustion engine simulations, which relies on the analytical computation of the ordinary differential equations (ODE) system Jacobian matrix in sparse form. Arbitrary reaction behaviors in either Arrhenius, third-body or fall-off formulations can be considered, and thermodynamic gas-phase mixture properties are evaluated according to the well-established 7-coefficient JANAF polynomial form. The current work presents a full validation of the new chemistry solver when coupled to the KIVA-4 code, through modeling of a single cylinder Caterpillar 3401 heavy-duty engine, running in two-stage combustion mode.

Computational simulations of the spray combustion and emissions formation processes in a heavy-duty DI diesel engine and in a small-bore DI diesel engine with a complicated injection schedule were performed by using the modified KIVA3V, rel. 2 code. Some initial parameter sets varying engine operating conditions, such as injection pressure, injector nozzle diameter, EGR load, were examined in order to evaluate their effects on the engine performance. Full-scale combustion chamber representations on 360-deg, Cartesian and polar, multiblock meshes with a different number of sprays have been used in the modelling unlike the conventional approach based on polar sector meshes covering the region around one fuel spray. The spray combustion phenomena were simulated using the detailed chemical mechanism for diesel fuel surrogate (69 species and 306 reactions).

For the investigation of the tribological behavior of lubricated contacts, the choice and the calibration of the adopted asperity contact model is fundamental, in order to properly mimic the mixed lubrication conditions. The Greenwood/Tripp model is extensively adopted by the commercial software commonly employed to simulate lubricated contacts. This model, based on a statistic evaluation of the number of asperities in contact and on the Hertzian contact theory, has the advantage of introducing a simple relationship between oil film thickness and asperity contact pressure, considerably reducing the simulation time. However, in order to calibrate the model, some non-standard roughness parameters are required, that are not available from commercial roughness measuring equipment. Standard values, based on some limited experiences, are typically used, and a limited literature can be found focusing on how to evaluate them, thus reducing the predictivity of the model.

Emission legislation for Off Road Engines is forcing the industry to review the engine design, introducing state of the art technology for many components and tailored exhaust gas after treatment architectures. Particulate matter reduction is a crucial issue to be addressed having an influence on overall engine performance and cost. At the present stage there is not a unilateral solution in the industry, as some manufacturers use a combination of very high fuel injection pressure and very efficient DOC, while others rely on the automotive derived DPF technology with active regeneration or SCR-only technology to reach EU Stage IV and US Tier4f. Considering the pros and cons of each solution, VM Motori decided to adopt an innovative solution consisting in a DOC followed by a partial-flow filter PM-Metalit® for the R750 Engine family. The advantages of this solution will be discussed in this paper along with the application work that has been carried over to reach the emission limit.