Search Results

As global automobile manufacturers prepare for the phase-out of R134a in Europe, they must address the issue of using the new refrigerant for European sales only or launching the product worldwide. Several factors play into this decision, including cost, service, risk, customer satisfaction, capacity, efficiency, etc. This research effort addresses the minimal vehicle-level hardware differences necessary to provide a European solution of R1234yf while continuing to install R134a into vehicles for the rest of the world. It is anticipated that the same compressor, lubricant and condenser; most fluid transport lines; and in most cases the evaporator can be common between the two systems.

There are benefits of using ultra thin wall (UTW) substrates (i.e., 900/2, 400/4, etc) in lowering cost and emission level. However, the more fragile mechanical characteristics of the UTW present a challenge to design and manufacture of robust catalytic converters. This paper describes a method of canning trial, where a combined Design of Experiment / Monte-Carlo analysis method was used, to develop and validate a canning method for ultra thin wall substrates. Canning trials were conducted in two stages-- Prototype Canning Trial and Production Canning Trial. In Prototype Canning Trial, the root cause of substrate failure was identified and a model for predicting substrate failure was established. Key factors affecting scrap rate and gap capability were identified and predictions were performed on scrap rate and gap capability with the allowed variations in the key factors. The results provided guidelines in designing production line and process control.

The purpose of this paper is to demonstrate our success in taking advantage of model-based development tools and auto-code technology to accelerate the typical life cycle development of powertrain software. In particular, we applied the technology as a clean sheet approach to Visteon's third generation Electronic Throttle Control system. In the process of applying model-based development and 100% auto-code, we identified various pitfalls and created solutions to overcome the gap between technology and development process during each phase of the entire software development life cycle. We will share our lessons learned during the requirement, design, implementation, and validation stages.

This paper describes two electronic throttle controllers of Visteon Corporation with one already in production and the other currently under development. Analysis and tuning of the two controllers are described. The general structure of the controllers consists of a reference shaping subsystem and a proportional-plus-integral-plus-derivative(PID) controller supplemented with additional terms that deal with the nonlinearility of the electronic throttle body. Due to a friction cancellation term in the controller that minimizes the nonlinearity of the system, linear system analysis techniques are applied. The transfer functions of the electronic throttle body at six different operating conditions are derived. Analysis of the closed-loop dynamics is performed based on the plant and the controller transfer-functions. Controller fine-tuning is performed using frequency response techniques, MATLAB simulations and testing on the actual system.

In Brazil the market for plastic parts molds, in last few years had become very competitive, with several Vehicle Operations and a big number of a different models, and with today total market volume it means low volumes productions for each model. This market demands for good toolshops and at the same time a big pressure to reduce investments, one of the most important. Plastic components usage in the car, is increasing overtime, with new applications for Exterior, interior and powertrain, requiring new technologies for Injection molding processing and making molds to be more complex. The development of plastic parts in Brazil has its own characteristics, strengths and weaknesses. In fact a big and heterogeneous market. This paper intends to present an analysis of development of plastic parts in Brazil, considering the development of mold tooling locally, focusing the automotive market.

Evolutionary Operation (EVOP) experimental design using Sequential Simplex method is an effective and robust means for determining the ideal process parameter (factor) settings to achieve optimum output (response) results. EVOP is the methodology of using on-line experimental design. Small perturbations to the process are made within allowable control plan limits, to minimize any product quality issues while obtaining information for improvement on the process. It is often the case in high volume production where issues exist, however off-line experimentation is not an option due to production time, the threat of quality issues and costs. EVOP leverages production time to arrive at the optimum solution while continuing to process saleable product, thus substantially reducing the cost of the analysis.

A major part of product development is to validate robustness to the environment (e.g. temperature, vibration, EMC). Although much time and expense is spent doing so, using traditional approaches often leads to “feel good” results since the product “passes”. Such a false sense of security is misleading since such validation methods can have serious deficiencies. Presented is a Design Assurance process (Accelerated Stress Assurance Plan - ASAP) to validate modules that addresses these deficiencies. It places major emphasis on the analysis and development stages. It does not require large sample sizes, and overall test time and facilities is reduced (30-50% possible).. Just as for electronic modules, new and major changes to IC's need a shorter validation process. As an example, a relatively fast procedure for the production and application release of improved molding compounds for IC's is presented.