Refine Your Search

Topic

Search Results

Technical Paper

Analysis of Coatings Appearance and Durability Testing Induced Surface Defects Using Image Capture/Processing/Analysis

2001-03-05
2001-01-3798
This paper describes the applicability of optical imaging techniques to the analysis of the scratch resistance of automotive interior plastic materials. The evaluation of so-called “finger testing” has traditionally relied upon human vision for detection of the initial scratch position. Commonly performed under uniform and defined illumination conditions, the relative contrast difference signified by whitening on a surface as determined by unaided human vision is a highly variable subjective perception; thus individual inspectors may determine the “whitening” point differently. This paper compares test data obtained from both visual and instrumental evaluation methods and discusses the advantages of optical imaging techniques for surface defect analysis.
Technical Paper

Power Distribution for Spacecraft Payloads that Employ State of the Art Radiation Hardened Integrated Circuits

2006-11-07
2006-01-3058
Recent advances in the state of the art of space-borne data processors and signal processors have occurred that present some unprecedented constraints relating to their power needs. Such processors include the class of multiprocessors providing computational capabilities in the billions of floating point operations per second. Processors of this type tend to require use of modern radiation tolerant or radiation hardened integrated circuits requiring very low voltage power supplies that place considerable challenge on power distribution and conversion within those processing payloads. The primary challenges are efficient conversion of power from the spacecraft power bus to these low voltages and distribution of the very high accompanying currents within the payload while maintaining proper voltage regulation (typically +/− 5%). Some integrated circuits require 10 Amps or more at 1Volt, as an example [3], [6].
Technical Paper

New Designs and Concepts for Vehicle Entertainment Systems

2006-11-21
2006-01-2828
The need for entertainment is a constant desire since human beans started to use vehicles for short and long distance travel. The radio, a home entertainment revolution, was the first one to be incorporated. The information and entertainment that initially brought the radio to the vehicles also started a major change on the interior and electrical systems. This revolution will require changes in vehicle design to accommodate the new concepts and features.
Technical Paper

Non-Linear Analysis of Tunable Compression Bushing for Stabilizer Bars

2004-03-08
2004-01-1548
Stabilizer bars in a suspension system are supported with bushings by a frame structure. To prevent the axial movement of the stabilizer bar within the bushing, several new stabilizer bar-bushing systems have been developed. The new systems introduce permanent compressive force between the bar and the bushing thereby preventing the relative movement of the bar within the bushing. This mechanical bond between the bar and the bushing can eliminate features such as grippy flats, collars etc. In addition, by controlling the compression parameters, the properties of the bushing such as bushing rates can be tuned and hence can be used to improve the ride and handling performance of the vehicle. In this paper, nonlinear CAE tools are used to evaluate one such compressively loaded bushing system. Computational difficulties associated with modeling such a system are discussed.
Technical Paper

Human Factors Flight Test Evaluation of an Airport Surface Display with Indications & Alerts (SURF IA)

2010-09-30
2010-01-1663
This paper presents the results of a human factors flight test evaluation of a display of Enhanced Traffic Situational Awareness on the Airport Surface with Indications and Alerts (SURF IA). The study is an element of the FAA-sponsored Surface Conflict Detection and Alerting with Consideration of Arrival Applications program. The objective of the flight test was to conduct a comparative evaluation of two candidate SURF IA displays: a detailed Airport Surface Situation Awareness (ASSA) display and a runways-only Final Approach Runway Occupancy Awareness (FAROA) display. Six pilots with a current Air Transport Pilot Certificate each completed 18 scenarios. A Beechcraft King Air C-90 and a Cessna Citation Sovereign aircraft were deployed for the flight tests. The scenarios were conducted at Seattle-Tacoma International Airport and at Snohomish County Paine Field Airport, with each aircraft acting as ‘traffic’ for the other aircraft.
Technical Paper

Blind Spot Monitoring by a Single Camera

2009-04-20
2009-01-1291
A practical and low cost Blind Spot Monitoring system is proposed. By using a single camera, the range and azimuth position of a vehicle in a blind spot are measured. The algorithm is based on the proposed RWA (Range Window Algorithm). The camera is installed on the door mirror and monitoring the side and rear of the host vehicle. The algorithm processes the image and identifies range and azimuth angle of the vehicle in the adjacent lane. This algorithm is applied to real situations. The 388 images including several kinds of vehicles are analyzed. The detection rate is 86% and the range accuracy is 1.6[m]. The maximum detection range is about 30[m].
Technical Paper

Environmental Systems Considerations for Aircraft Cabins During Ground Operation

2002-11-05
2002-01-2941
The quality of outside air during ground operations was analyzed by comparing airport and engine exhaust data to exposure limits and odor thresholds. The results indicated that the outside air may contain compounds in high enough concentrations to be odorous. If the odor is to be treated, the important design criteria that must be considered include the phase of compounds, compound type, location of treatment device on the aircraft, pressure drop, operating temperature, and maintenance interval. Finally, a control strategy is outlined that monitors the air quality as well as the efficiency of an air treatment system.
Technical Paper

Localized Nonlinear Model of Plastic Air Induction Systems for Virtual Design Validation Tests

2005-04-11
2005-01-1516
Plastic air induction system (AIS) has been widely used in vehicle powertrain applications for reduced weight, cost, and improved engine performance. Physical design validation (DV) tests of an AIS, as to meet durability and reliability requirements, are usually conducted by employing the frequency domain vibration tests, either sine sweep or random vibration excitations, with a temperature cycling range typically from -40°C to 120°C. It is well known that under high vibration loading and large temperature range, the plastic components of the AIS demonstrate much higher nonlinear response behaviors as compared with metal products. In order to implement a virtual test for plastic AIS products, a practical procedure to model a nonlinear system and to simulate the frequency response of the system, is crucial. The challenge is to model the plastic AIS assembly as a function of loads and temperatures, and to evaluate the dynamic response and fatigue life in frequency domain as well.
Technical Paper

A Discussion on Interior Compartment Doors and Latches

2004-03-08
2004-01-1483
Interior compartment doors are required by Federal Motor Vehicle Safety Standard (FMVSS) 201, to stay closed during physical head impact testing, and when subjected to specific inertia loads. This paper defines interior compartment doors, and shows examples of several different latches designed to keep these doors closed. It also explores the details of the requirements that interior compartment doors and their latches must meet, including differing requirements from automobile manufacturers. It then shows the conventional static method a supplier uses to analyze a latch and door system. And, since static calculations can't always capture the complexities of a dynamic event, this paper also presents a case study of one particular latch and door system showing a way to simulate the forces experienced by a latch. The dynamic simulation is done using Finite Element Analysis and instrumentation of actual hardware in physical tests.
Technical Paper

Communicating Outside of the Box: A Structural Model for Predicting Consumer Acceptance of In-Vehicle Electronics Implementations

2004-10-18
2004-21-0070
The era of the vehicle as a standalone non-connected entity is rapidly drawing to a close. The “Box” on four wheels is being opened to multiple communication channels based on consumer demand and expectations of the latest features, functions and content. Concurrently, automotive planners, marketers, engineers, and system architects are subject to increased complexity as a result of the rapidly evolving consumer electronics industry. This paper will discuss many of the limitations of existing automotive business models in attempting to successfully implement and meet consumer expectations. It will also propose a structural framework for automotive planners, marketers, engineers, and system architects to be able to better understand and predict consumer acceptance of electronics, multimedia features, and in-vehicle content access.
Journal Article

Advanced Electric Drives for Aerospace More Electric Architectures

2008-11-11
2008-01-2861
This paper discusses the problem of obtaining electric machines (EM) for advanced electric drives (AED) used in more electric architecture (MEA) applicable to aircraft, spacecraft, and military ground vehicles. The AED are analyzed by those aspects of Six Sigma theory that relate to critical-to-quality (CTQ) subjects. Using this approach, weight, volume, reliability, efficiency, and cost CTQ are addressed to develop a balance among them, resulting in an optimized system. The influence of machine controllers and system considerations is discussed. As a part of the machine evaluation process, speeds, bearings, complexities, rotor mechanical and thermal limitations, torque pulsations, currents, and power densities are considered. A methodology for electric machine selection is demonstrated. An example of high-speed, high-performance machine application is shown. A system approach is used for overall electric machine selection and optimization.
Journal Article

Ensuring Audio Signal Quality in Automotive Infotainment Systems

2013-04-08
2013-01-0163
In automotive infotainment systems, multiple types of digital audio signals are usually present. Some come from internal sources, such as a CD or USB stick, and some come from external sources, such as an internet stream or digital radio. These sources usually have different sample-rates, and may also be different from one or more system sample-rates. Managing and transporting these signals throughout the system over different sample-rate domains require detailed upfront architecture analysis and correct system design to ensure signal quality is maintained to the desired level. Incorrect design can add significant user-perceivable noise and distortion. This paper examines the key analysis factors, the effects of poor design and the approaches for achieving robust signal handling and ensuring desired signal quality.
Technical Paper

Overview of Automotive Plastic Parts Molds Development of in Brazil

2003-11-18
2003-01-3565
In Brazil the market for plastic parts molds, in last few years had become very competitive, with several Vehicle Operations and a big number of a different models, and with today total market volume it means low volumes productions for each model. This market demands for good toolshops and at the same time a big pressure to reduce investments, one of the most important. Plastic components usage in the car, is increasing overtime, with new applications for Exterior, interior and powertrain, requiring new technologies for Injection molding processing and making molds to be more complex. The development of plastic parts in Brazil has its own characteristics, strengths and weaknesses. In fact a big and heterogeneous market. This paper intends to present an analysis of development of plastic parts in Brazil, considering the development of mold tooling locally, focusing the automotive market.
Technical Paper

Test Strategy for Linux based Platforms using Open Source Tools

2016-04-05
2016-01-0053
Today open source software is widely used in different domains like Desktop systems, Consumer electronics (smart phones, TV, washing machines, camera, printers, smart watches), Automotive, Automation etc. With the increased involvement of the open source software in the different domains including the safety critical ones, there has been a requirement of the well-defined test strategy to test and verify such systems. Currently there are multiple open source tools and frameworks to choose from. The paper describes the various open source test strategies and tools available to qualify such systems, their features, maintenance, community support, advantages and disadvantages. Target audience would be the software engineers, program managers, using an open source stack for the product development.
Technical Paper

Statistical Modeling of Fatigue Crack Growth in Wing Skin Fastener Holes

2012-04-16
2012-01-0482
Estimation and prediction of residual life and reliability are serious concerns in life cycle management for aging structures. Laboratory testing replicating fatigue loading for a typical military aircraft wing skin was undertaken. Specimens were tested until their fatigue life expended reached 100% of the component fatigue life. Then, scanning electron microscopy was used to quantify the size and location of fatigue cracks within the high stress regions of simulated fastener holes. Distributions for crack size, nearest neighbor distances, and spatial location were characterized statistically in order to estimate residual life and to provide input for life cycle management. Insights into crack initiation and growth are also provided.
Technical Paper

Reinforcement Challenges and Solutions in Optimized Design of Injection Molded Plastic Parts

2003-03-03
2003-01-1123
The mechanical performance of injection molded glass-fiber reinforced plastic parts is highly anisotropic and depends strongly on the kinetics (orientation and distribution) of the glass-fiber and the part geometry. Similarly, the bulk and local mechanical performance at the ribs, walls and welds is influenced by these glass-fibers and the specific processing technology (including joining) used, as related to melt-flow and melt-pool formation and glass-fiber re-orientation. The purpose of this study is to show: the effect of short glass-fiber orientation at the pre-welded beads, ribs and wall areas for injection molded and subsequently welded parts the short-term mechanical performance of welded butt-joints that have various geometry and thickness, namely “straight” and “T-type” welds.
Technical Paper

Interior Fittings – A Global View

2003-03-03
2003-01-1175
In today's global economy, the automotive design engineer's responsibilities are made more complex by the differences between regulatory requirements of the various global markets. This paper compares instrument panel head impact requirements of FMVSS 201 with its European counterparts, ECE 21, and EEC/74/60, Interior Fittings. It describes the similarities and differences between these regulations and explains the unique requirements for each market. It then compares processes for development and validation testing in both markets. It also covers related topics like self-certification, witness testing, radii, projections, and interior compartment doors. The cockpit design engineer will gain an understanding of the factors involved in ensuring that their design fully meets the requirements of the subject regulations.
Technical Paper

CAE Virtual Door Slam Test for Plastic Trim Components

2003-03-03
2003-01-1209
Visteon has developed a CAE procedure to qualify plastic door trim assemblies under the vehicle door slam Key Life Test (KLT) environments. The CAE Virtual Door Slam Test (VDST) procedure simulates the environment of a whole door structural assembly, as a hinged in-vehicle door slam configuration. It predicts the durability life of a plastic door trim sub-assembly, in terms of the number of slam cycles, based on the simulated stresses and plastic material fatigue damage model, at each critical location. The basic theory, FEA methods and techniques employed by the VDST procedure are briefly described in this paper. Door trim project examples are presented to illustrate the practical applications and their results, as well as the correlation with the physical door slam KLTs.
Technical Paper

Honeywell's Automotive Door Latch Design is Ideal for Corporate Latch Strategy

2003-03-03
2003-01-1190
In response to consumer demand, automakers are adding more safety, security, and convenience features to vehicle access control systems. Also, in a continuing effort to be more profitable, automakers are reducing costs by outsourcing the design of systems/sub-systems/components, reducing their supply base, and minimizing part numbers by sharing components across several platforms. In an attempt to improve efficiency and productivity, many OEM's have adopted a “corporate latch” strategy, implementing the same latch across several manufacturing platforms and marketing divisions. Honeywell's revolutionary door latch design efficiently and cost effectively addresses vehicle OEMs' current and future requirements for performance and functionality.
Technical Paper

Photometric and Colorimetric Measurement Procedures for Airborne Electronic Flat Panel Displays — SAE ARP 4260

2009-11-10
2009-01-3143
SAE ARP 4260 Photometric and Colorimetric Measurement Procedures for Airborne Electronic Flat Panel Displays [1] has recently been revised. This new revision reaffirms that ARP 4260 is pertinent to the aviation industry, changes the content to keep up with the state of the art, and adds clarification where needed. ARP 4260 contains methods used to measure the optical performance of airborne electronic flat panel display systems and is referenced in SAE ARP 4256, Design Objectives for Liquid Crystal Displays for Part 25 (Transport) Aircraft [2] and in SAE AS 8034, Minimum Performance Standard for Airborne Multipurpose Electronic Displays [3].
X