Refine Your Search


Search Results

Technical Paper

Heat Simulation in Lighting

During last 10-15 years we could have seen quite big changes in automotive lighting. The most important changes are: a) plastic materials mostly removed metal and glass material from lighting products raised heat issue of plastics materials b) escalation of competition between lighting suppliers (globalization, merging, …) decrease of time and cost for development of the new product as much as possible
Technical Paper

Analysis of Coatings Appearance and Durability Testing Induced Surface Defects Using Image Capture/Processing/Analysis

This paper describes the applicability of optical imaging techniques to the analysis of the scratch resistance of automotive interior plastic materials. The evaluation of so-called “finger testing” has traditionally relied upon human vision for detection of the initial scratch position. Commonly performed under uniform and defined illumination conditions, the relative contrast difference signified by whitening on a surface as determined by unaided human vision is a highly variable subjective perception; thus individual inspectors may determine the “whitening” point differently. This paper compares test data obtained from both visual and instrumental evaluation methods and discusses the advantages of optical imaging techniques for surface defect analysis.
Technical Paper

High Efficient LED Headlamp Design-Styling versus Light Performance

First LED headlamps will be released into the market in 2007. Special permissions allow this introduction although the official regulation is still under discussion in ECE. The LED technology for front lighting has entered into a new phase from theoretical, prototype status to real and practical applications. Additionally in Europe the legislation, which is under preparation, defines LED modules with one or more LED chips in a row which should be replaceable. With this boundary conditions headlamp suppliers needs to balance between an attractive and innovative styling, demanded by car manufacturers and the light performance to gurantee good visibility at night. The paper describes the methods how to design an LED headlamp with high efficiency by keeping in mind the parameters: packaging, weight, styling and light perfromance. Results with specific design proposals are shown.
Technical Paper

Design Parameter Tradeoffs for LED Headlamp Applications

High-power LEDs and LED headlamps have become a serious consideration for the automotive industry. White LEDs have achieved the required performance for initial automotive headlamp applications. However tradeoffs among several attributes such as efficiency, cost, weight and performance profoundly affect LED headlamp development and need to be addressed by vehicle manufacturers, lamp set makers and LED source suppliers in order for LED headlamps to be effective. The solutions to these tradeoffs relates to the behavior of the LED sources, the thermo-mechanical integration of LEDs in a headlamp environment and input from the vehicle manufacturer regarding styling and packaging for an LED headlamp on the respective targeted vehicles.
Technical Paper

Construction and Application of Near Field (TIR Type) Lenses for Automotive Lighting Functions

Light Emitting Diodes (LEDs) are fast becoming the preferred light sources for automotive lighting applications. They emit light at cone angles equal (hemispherical) or less (conical) than 2Π radians. One way for efficiently collecting and collimating light from LED light sources is to use Near Field Lenses (NFLs). NFLs are collimators using refraction and total internal reflection (TIR) to efficiently collect and direct light. They tend to have thick sections and therefore require challenging molding techniques, and they may have the LED source optically coupled directly into them. Beside these functional aspects, NFLs offer unique styling for different lighting functions such as those in rear combination lamps (RCLs), front turn signal lamps, daytime running lamps (DRLs) and headlamps.
Technical Paper

Novel High Performance Fiber-High Speed Test Development

The major objective of this paper is to address how the actual force versus extension relationship for a seat belt during a collision is different from the one obtained at typical low rate (static) conditions. We also look at what features of the tensile stress-strain characteristic are important for the optimal performance of a seat belt. To answer these questions experimentally we use our high rate Instron -1331. We also designed an experimental set up that required special grips and contact sensors for characterizing samples of belt and yarn. In the theoretical part we demonstrate the selected rates for the tensile testing as relevant to the collisions. We also discuss the importance of the energy absorbing capacity of the belts as the most relevant characteristic of the tensile curves for this application. We then show the effect of visco-elastic factors on energy absorbing properties of fibers during collisions and the role of weaving and dyeing the belt.
Technical Paper

Target Tracking by a Single Camera Based on Range-Window Algorithm and Pattern Matching

An algorithm, which determines the range of a preceding vehicle by a single image, had been proposed. It uses a “Range-Window Algorithm”. Here in order to realize higher robustness and stability, the pattern matching is incorporated into the algorithm. A single camera system using this algorithm has an advantage over the high cost of stereo cameras, millimeter wave radar and non-robust mechanical scanning in some laser radars. And it also provides lateral position of the vehicle. The algorithm uses several portions of a captured image, namely windows. Each window is corresponding to a predetermined range and has the fixed physical width and height. In each window, the size and position of objects in the image are estimated through the ratio between the widths of the objects and the window, and a score is given to each object. The object having the highest score is determined as the best object. The range of the window corresponding to the best object becomes an estimated range.
Technical Paper

Non-Linear Analysis of Tunable Compression Bushing for Stabilizer Bars

Stabilizer bars in a suspension system are supported with bushings by a frame structure. To prevent the axial movement of the stabilizer bar within the bushing, several new stabilizer bar-bushing systems have been developed. The new systems introduce permanent compressive force between the bar and the bushing thereby preventing the relative movement of the bar within the bushing. This mechanical bond between the bar and the bushing can eliminate features such as grippy flats, collars etc. In addition, by controlling the compression parameters, the properties of the bushing such as bushing rates can be tuned and hence can be used to improve the ride and handling performance of the vehicle. In this paper, nonlinear CAE tools are used to evaluate one such compressively loaded bushing system. Computational difficulties associated with modeling such a system are discussed.
Technical Paper

Human Factors Flight Test Evaluation of an Airport Surface Display with Indications & Alerts (SURF IA)

This paper presents the results of a human factors flight test evaluation of a display of Enhanced Traffic Situational Awareness on the Airport Surface with Indications and Alerts (SURF IA). The study is an element of the FAA-sponsored Surface Conflict Detection and Alerting with Consideration of Arrival Applications program. The objective of the flight test was to conduct a comparative evaluation of two candidate SURF IA displays: a detailed Airport Surface Situation Awareness (ASSA) display and a runways-only Final Approach Runway Occupancy Awareness (FAROA) display. Six pilots with a current Air Transport Pilot Certificate each completed 18 scenarios. A Beechcraft King Air C-90 and a Cessna Citation Sovereign aircraft were deployed for the flight tests. The scenarios were conducted at Seattle-Tacoma International Airport and at Snohomish County Paine Field Airport, with each aircraft acting as ‘traffic’ for the other aircraft.
Technical Paper

Blind Spot Monitoring by a Single Camera

A practical and low cost Blind Spot Monitoring system is proposed. By using a single camera, the range and azimuth position of a vehicle in a blind spot are measured. The algorithm is based on the proposed RWA (Range Window Algorithm). The camera is installed on the door mirror and monitoring the side and rear of the host vehicle. The algorithm processes the image and identifies range and azimuth angle of the vehicle in the adjacent lane. This algorithm is applied to real situations. The 388 images including several kinds of vehicles are analyzed. The detection rate is 86% and the range accuracy is 1.6[m]. The maximum detection range is about 30[m].
Technical Paper

Environmental Systems Considerations for Aircraft Cabins During Ground Operation

The quality of outside air during ground operations was analyzed by comparing airport and engine exhaust data to exposure limits and odor thresholds. The results indicated that the outside air may contain compounds in high enough concentrations to be odorous. If the odor is to be treated, the important design criteria that must be considered include the phase of compounds, compound type, location of treatment device on the aircraft, pressure drop, operating temperature, and maintenance interval. Finally, a control strategy is outlined that monitors the air quality as well as the efficiency of an air treatment system.
Technical Paper

CAE Virtual Test of Air Intake Manifolds Using Coupled Vibration and Pressure Pulsation Loads

A coupled vibration and pressure loading procedure has been developed to perform a CAE virtual test for engine air intake manifolds. The CAE virtual test simulates the same physical test configuration and environments, such as the base acceleration vibration excitation and pressure pulsation loads, as well as temperature conditions, for design validation (DV) test of air intake manifolds. The original vibration and pressure load data, measured with respect to the engine speed rpm, are first converted to their respective vibration and pressure power spectrum density (PSD) profiles in frequency domain, based on the duty cycle specification. The final accelerated vibration excitation and pressure PSD load profiles for design validation are derived based on the key life test (KLT) duration and reliability requirements, using the equivalent fatigue damage technique.
Technical Paper

Localized Nonlinear Model of Plastic Air Induction Systems for Virtual Design Validation Tests

Plastic air induction system (AIS) has been widely used in vehicle powertrain applications for reduced weight, cost, and improved engine performance. Physical design validation (DV) tests of an AIS, as to meet durability and reliability requirements, are usually conducted by employing the frequency domain vibration tests, either sine sweep or random vibration excitations, with a temperature cycling range typically from -40°C to 120°C. It is well known that under high vibration loading and large temperature range, the plastic components of the AIS demonstrate much higher nonlinear response behaviors as compared with metal products. In order to implement a virtual test for plastic AIS products, a practical procedure to model a nonlinear system and to simulate the frequency response of the system, is crucial. The challenge is to model the plastic AIS assembly as a function of loads and temperatures, and to evaluate the dynamic response and fatigue life in frequency domain as well.
Technical Paper

Robustness Considerations in the Design of a Stabilizer Bar System

Modern automobiles utilize stabilizer bars to increase vehicle roll stiffness. Stabilizer bars are laterally mounted torsional springs which resist vertical displacement of the wheels relative to one another. A stabilizer bar is constructed in such a way that it will meet package constraints and fatigue requirements. In order to design a robust stabilizer bar, Taguchi's “Design of Experiment method” is used. The objective of this paper is to develop a robust stabilizer bar design that will maximize the fatigue life and the roll stiffness while minimizing weight. This study is based on results obtained by CAE analysis.
Technical Paper

Compressor Body Temperature and Lubrication

The paper addresses compressor body temperature (crankcase) importance to the vehicle AC system long-term durability. Majority of OEM vehicle test evaluation is to see if AC system can pass compressor discharge temperature and discharge pressure targets. Most OEMs adopt 130°C max compressor discharge temperature and 2350 kpag head pressure as the target. From the field, although some of the compressor failure results from a high compression ratio, and compressor discharge temperature that are caused by the poor front end airflow, etc., high percentage compressor failed systems exhibit not too high compression ratio and compressor discharge temperature, but having the trace of high temperature in the shaft area, gasket area, etc. With introducing more and more variable swash plate compressor applications, OEMs start to see more and more compressor failures that are not related to a high compressor discharge temperature but the trace of high compressor body temperature.
Technical Paper

A Discussion on Interior Compartment Doors and Latches

Interior compartment doors are required by Federal Motor Vehicle Safety Standard (FMVSS) 201, to stay closed during physical head impact testing, and when subjected to specific inertia loads. This paper defines interior compartment doors, and shows examples of several different latches designed to keep these doors closed. It also explores the details of the requirements that interior compartment doors and their latches must meet, including differing requirements from automobile manufacturers. It then shows the conventional static method a supplier uses to analyze a latch and door system. And, since static calculations can't always capture the complexities of a dynamic event, this paper also presents a case study of one particular latch and door system showing a way to simulate the forces experienced by a latch. The dynamic simulation is done using Finite Element Analysis and instrumentation of actual hardware in physical tests.
Journal Article

Advanced Electric Drives for Aerospace More Electric Architectures

This paper discusses the problem of obtaining electric machines (EM) for advanced electric drives (AED) used in more electric architecture (MEA) applicable to aircraft, spacecraft, and military ground vehicles. The AED are analyzed by those aspects of Six Sigma theory that relate to critical-to-quality (CTQ) subjects. Using this approach, weight, volume, reliability, efficiency, and cost CTQ are addressed to develop a balance among them, resulting in an optimized system. The influence of machine controllers and system considerations is discussed. As a part of the machine evaluation process, speeds, bearings, complexities, rotor mechanical and thermal limitations, torque pulsations, currents, and power densities are considered. A methodology for electric machine selection is demonstrated. An example of high-speed, high-performance machine application is shown. A system approach is used for overall electric machine selection and optimization.
Technical Paper

Overview of Automotive Plastic Parts Molds Development of in Brazil

In Brazil the market for plastic parts molds, in last few years had become very competitive, with several Vehicle Operations and a big number of a different models, and with today total market volume it means low volumes productions for each model. This market demands for good toolshops and at the same time a big pressure to reduce investments, one of the most important. Plastic components usage in the car, is increasing overtime, with new applications for Exterior, interior and powertrain, requiring new technologies for Injection molding processing and making molds to be more complex. The development of plastic parts in Brazil has its own characteristics, strengths and weaknesses. In fact a big and heterogeneous market. This paper intends to present an analysis of development of plastic parts in Brazil, considering the development of mold tooling locally, focusing the automotive market.
Technical Paper

Development of a Fuel Efficient Multipurpose 75W-90 Gear Lubricant

Automotive gear oil development has expanded beyond the historical requirements of emphasizing wear protection to encompass modern needs for fuel economy and limited slip frictional properties. This paper describes the development process of a new generation, fuel efficient gear lubricant for use in light duty vehicles. A systematic formulation approach was used, encompassing fluid viscometrics and additive optimization. Performance testing in both laboratory and vehicle tests is described. Though standard GL-5 tests were used to confirm oxidation, wear and corrosion performance, emphasis is given to those methods used for optimizing fuel economy.
Technical Paper

Statistical Modeling of Fatigue Crack Growth in Wing Skin Fastener Holes

Estimation and prediction of residual life and reliability are serious concerns in life cycle management for aging structures. Laboratory testing replicating fatigue loading for a typical military aircraft wing skin was undertaken. Specimens were tested until their fatigue life expended reached 100% of the component fatigue life. Then, scanning electron microscopy was used to quantify the size and location of fatigue cracks within the high stress regions of simulated fastener holes. Distributions for crack size, nearest neighbor distances, and spatial location were characterized statistically in order to estimate residual life and to provide input for life cycle management. Insights into crack initiation and growth are also provided.