Search Results

This Standard covers air data equipment (hereinafter designated the instrument) which when connected to sources of aircraft electrical power, static pressure, total pressure and outside air temperature (singly or in combination) provides some or all of the following computed air data output signals: Pressure Altitude* Total Temperature* Pressure Altitude (Reporting) Altitude Rate Baro-Corrected Pressure Altitude* Overspeed Warning Vertical Speed* Altitude Hold Computed Airspeed* Airspeed Hold Mach Number* Mach Hold Maximum Allowable Airspeed* qc (impact pressure) Static Air Temperature (*when used as an alternate for total temperature) True Airspeed Others

This Aeronautical Standard covers Flight Directors for use on aircraft to indicate to the Pilot, by visual means, the correct control application for the operation of an aircraft in accordance with a pre-selected flight plan.

These recommendations cover the mechanical and electrical installation and installation test procedures for automatic pilots of the type normally used in transport type aircraft. The material in this ARP does not supercede any airworthiness requirement in the Civil Air Regulations.

These recommendations cover the mechanical and electrical installation and installation test procedures for automatic pilots of the type normally used in transport type aircraft. The material in this ARP does not supercede any airworthiness requirement in the Civil Air Regulations.

These recommendations cover the mechanical and electrical installation and installation test procedures for automatic pilots of the type normally used in transport type aircraft. The material in this ARP does not supercede any airworthiness requirement in the Civil Air Regulations.

This SAE Aerospace Standard (AS) covers automatic pilots intended for use on aircraft to automatically operate the primary and trim aerodynamic controls to maintain stable flight and/or to provide maneuvering about any of the three axes through servo control. Automatic control functions essential for primary or augmented flight control are excluded.

This SAE Aerospace Standard (AS) covers automatic pilots intended for use on aircraft to automatically operate the primary and trim aerodynamic controls to maintain stable flight and/or to provide maneuvering about any of the three axes through servo control. Automatic control functions essential for primary or augmented flight control are excluded.

This Aerospace Standard covers Automatic Pilots intended for use on aircraft to automatically operate the primary and trim aerodynamic controls to maintain stable flight and/or to provide maneuvering about any of the three axes through servo control. Automatic control functions essential for primary or augmented flight control are excluded.

This Aeronautical Standard covers the capacitance sensor type of instrument.

This specification covers that gyroscopic instrument normally defined as a "subminiature rate gyro." The rate gyro, when subjected to an angular rate about its input axis, provides an AC output voltage proportional to the angular rate. The subminiature size category generally includes gyro instruments of one (1) inch diameter or less and three and one-half (3 1/2) inches length or less. This specification defines the requirements for a subminiature spring-restrained, single-degree-of-freedom rate gyro for aircraft, missile, and spacecraft applications.

This standard provides minimum performance criteria for air data instruments intended to provide cockpit indication of: a Indicated airspeed (Vi) b Computer airspeed (Vc) c True airspeed (Vt) d Equivalent airspeed (Ve) e Mach number (M) f Altitude (H) g Vertical speed (Hpr) h Maximum operating limit speed (Vmo) i True angle of attack (αt) j Free air temperature (Tfat) k Total temperature (Tt) These functions shall be derived from a central air data computer (AS 417) and through system wiring applied to the respective indicator.

All automatic altitude reporting digitizer equipment manufactured under this standard shall comply with the requirements as specified up to its maximum range as indicated on the equipment nameplate.

This Aerospace Standard covers two basic types of pitch and roll indicating instruments as follows: Type I: Direct coupled to gyro Type II: Electrical repeating

This AS covers __________ which measure and display __________ or This AS covers __________ basic types of (no capitals) instruments as follows: Note: Each type number to be followed by a brief description as it would if the scope were covering only a single type. As many types as required may be used.

This Aerospace Standard, (AS), specifies minimum performance standards for _____________ (Instrument or instrument systems) which are primarily intended for use with (vehicles capable of flight), ((fixed wing, rotary wing) aircraft)), (other special modifiers); (and whose purpose is to display _____________ information).

This Aerospace Standard, (AS), specifies minimum performance standards for _____________ (Instrument or instrument systems) which are primarily intended for use with (vehicles capable of flight), ((fixed wing, rotary wing) aircraft)), (other special modifiers); (and whose purpose is to display _____________ information).

This Aerospace Standard covers ____________________ or SCOPE This Aerospace Standard covers ____________________ basic types of (no capitals) instruments as follows: NOTE: Each type number to be followed by a brief description. As many types as required may be used.

This specification covers the design and performance requirements for a single axis, four load-factor level counting accelerometer group referred to hereafter as “equipment.”

This specification covers the design and performance requirements for a single axis, four load-factor level counting accelerometer group referred to hereafter as “equipment.”

The instrument system specified shall accept an input of static pressure and in some equipment other inputs that contribute altitude information to provide a visual indication of pressure altitude. If equipped with an automatic correction mechanism, it shall indicate by a positive means when the automatic correction mechanism is not in use. If the static source pressure error compensating mechanism is operational it shall be functional throughout the required operating envelope of the particular aircraft. Each aircraft type has its own static source error data which shall be obtained from the airframe manufacturer’s certified data. When a Central Air Data Computer is used in the altimeter system, the CADC shall be certified to its own governing document and the altimeter system (CADC and display) shall comply with the requirements of this document. NOTE: The instrument system specified herein does not include the aircraft pressure lines and pressure sources.