Refine Your Search

Search Results

Viewing 1 to 14 of 14
Standard

Development and Qualification of Composite Landing Gears

2016-01-04
WIP
AIR5552A
This information report provides general guidance for the design considerations, qualification in endurance, strength and fatigue of landing gear using composite components as principle structural elements. The information discussed herein includes the development and evaluation of design data considering: the potential for imbedded manufacturing defects, manufacturing process variations, the component operating environment, potential damage threats in service, rework and overhaul, and inspection processes. This AIR mainly discusses the use of thick composites for landing gear structural components. Considerations and recommendations provided in this AIR may therefore differ greatly from considerations and recommendations found in widely accepted composite design references such as CMH-17 and Advisory Circulars such as AC 20-107(B).
Standard

Information on Hard Landings

2018-02-27
WIP
AIR5938A

This document provides information on the current practices used by commercial and military operators in regards to hard landings (or overload events designated as hard landings). Since detailed information on inspections would be aircraft specific, this AIR provides only a general framework. Detailed information and procedures are available in the maintenance manuals for specific aircraft.

Because hard landings potentially affect the entire aircraft, guidelines are listed here for non-landing gear areas. But, the primary focus of the document is the landing gear and related systems. The document may be considered to be applicable to all types of aircraft.

This document does NOT provide recommended practices for hard landing inspections, nor does it provide recommendations on the disposition of damaged equipment. Refer to ARP 4915 and ARP 5600.

Standard

SAFE-LIFE LIMITS FOR LANDING GEAR STRUCTURES

2018-04-26
WIP
AIR6949
This document describes the approaches taken to define safe-life limits for the management of fatigue in landing gear structures, and the substantiation of those limits through full-scale fatigue testing. The safe-life scatter factors considered in a range of military and civil regulatory standards are also reviewed.
Standard

Landing Gear Safety Criticap Processes

2018-02-28
WIP
AIR6813
There are a number of safety critical processes that are common to landing gear systems. A safety critical process (CSP) is a landing gearmaintenance manufacturing, repair or overhaul process which if ommitted or preformed incorrectly will cause failure of a safety citical item (CSI) in operation. A CSI is a landing gear item whose failure or omission will cause more than $1M in damage, serious injury or death. This AIR will define methods and modes of failure for CSPs based on experience.
Standard

Landing Gear Shock Strut Hydraulic Fluid

2004-01-30
HISTORICAL
AIR5358
This SAE Aerospace Information Report (AIR) was prepared by a panel of the SAE A-5 Committee. This document establishes the specifications for fluids used in landing gear shock struts with extreme pressure and antiwear additives that have been added for improved lubrication. This document requires qualified products.
Standard

Specification for Landing Gear Shock Strut Hydraulic Fluid With Additives

2016-03-14
WIP
AS6409
Provide specifications for hydraulic fluids used in landing gear shock struts. Some of this information was previously in AIR5358 however specifications should be in an AS. This new document will contain the appropriate specifications for premixed hydraulic fluid with additives believed to improve fluid performance and reduce friction.
Standard

ARRESTING HOOK INSTALLATION, LAND BASED AIRCRAFT, EMERGENCY

1978-04-01
HISTORICAL
ARP1538
This document covers the recommended criteria and performance requirements for the design and installation of an aircraft emergency arresting hook intended for use with emergency runway arresting systems. Design criteria for fully operational hooks and for carrier based aircraft hook installations are contained in specification MIL-A-18717.
Standard

Arresting Hook Installation, Land Based Aircraft, Emergency

1998-02-01
HISTORICAL
ARP1538A
This document covers the recommended criteria and performance requirements for the design and installation of an aircraft emergency arresting hook intended for use with emergency runway arresting systems. Design criteria for fully operational hooks and for carrier based aircraft hook installations are contained in specification MIL-A-18717.
Standard

Landing Gear Integrity Program

2016-03-17
WIP
ARP6412
The scope of the Landing Gear Integrity Programs (LGIP) Aerospace Recommended Practice (ARP) is intended to assist in the safe-life structural integrity management of the landing gear system and subsystems components. In addition, component reliability, availability, and maintainability is included in a holistic LGIP.
Standard

Gland Design: Nominal 3/8 in Cross Section for Custom Compression Type Seals

1994-06-01
CURRENT
AS4832
This SAE Aerospace Standard (AS) offers gland details for a 0.364 cross section gland (nominal 3/8 in) with proposed gland lengths for compression type seals with two backup rings over a range of 8 to 20 in in diameter. A dash number system is proposed similar to AS568A. A 600 series has been chosen as a logical extension of AS568A and the 625 number has been arbitrarily chosen for the initial number. (Both 300 and 400 series begin with 325 and 425 sizes.) Seal configurations and design are not a part of this document. This gland is for use with custom compression type seals including, but not limited to, O-rings, T-rings, D-rings, etc.
Standard

Gland Design: Nominal 3/8 in Cross Section for Custom Compression Type Seals

2018-06-13
WIP
AS4832A
This SAE Aerospace Standard (AS) offers gland details for a 0.364 cross section gland (nominal 3/8 in) with proposed gland lengths for compression type seals with two backup rings over a range of 8 to 20 in diameter. A dash number system is proposed similar to AS568A. A 600 series has been chosen as a logical extension of AS568A and the 625 number has been arbitrarily chosen for the initial number. (Both 300 and 400 series begin with 325 and 425 sizes.) Seal configurations and design are not a part of this document. This gland is for use with custom compression type seals including, but not limited to, O-rings, T-rings, D-rings, etc.
X