The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852A and ARP4853A. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, reduce the certified safe life limit of the nose gear, or induce a stability problem during pushback and/or maintenance towing operations. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only. It is not meant for dispatch (operational) towing (see definitions in Section 3). Dispatch towing imposes greater loads on nose gears and structure due to additional passenger, cargo, and fuel loads.
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
This SAE Aerospace Recommended Practice (ARP) is intended to recommend a minimum standard, for the design and manufacturer of a self-propelled, chassis mounted passenger boarding vehicle. The vehicle will permit safe operation while minimizing aircraft damage and personnel safety hazards associated with commercial aircraft boarding operations. The vehicle described is intended to be used for assisting wheelchair passengers and passengers with disabilities on and off aircraft with door sill heights of 60 in (152.4 cm) and above.
This SAE Aerospace Recommended Practice (ARP) is intended to recommend a minimum standard, for the design and manufacturer of a self-propelled, chassis mounted passenger boarding vehicle. The vehicle will permit safe operation while minimizing aircraft damage and personnel safety hazards associated with commercial aircraft boarding operations. The vehicle described is intended to be used for assisting wheelchair passengers and passengers with disabilities on and off aircraft with door sill heights of 60 in (152.4 cm) and above.
This standard provides requirements for design and installation of aircraft jacking point adapters, as identified by ASCC AIR STD 25/7 Aircraft Jacking Pads, to permit use of standard jacking equipment.
This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.
This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for transport aircraft tow bars. It does not cover the requirements for tow bars intended for aircraft with a maximum ramp mass (MRW) below 8,600 kg (19,000 lb).
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for transport aircraft tow bars. It does not cover the requirements for tow bars intended for aircraft with a maximum ramp mass (MRW) below 8600 kg (19 000 lb).
This SAE Aerospace Recommended Practice (ARP) specifies dimensional and physical requirements of tow bar connections to tractor and aircraft (see Figure 1). It is applicable to all types of commercial transport category aircraft tow bar. The purpose of this SAE Aerospace Recommended Practice (ARP) is to standardize tow bar attachments to airplane and tractor according to the mass category of the towed aircraft, so that one tow bar head with different shear levels can be used for all aircraft that are within the same mass category and are manufactured in compliance with AS1614 or ISO 8267.
The tow vehicle should be designed for towbarless movement of aircraft on the ground. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode.
This SAE Aerospace Recommended Practice (ARP) is intended to recommend: a Uniform criteria for determination of wind loads that aircraft ground support equipment can encounter and yet allow personnel to work safely, b Uniform systems for maintaining stability (i.e., stabilizers, outriggers, spring lockout devices), c Standardization of specific types of interlock systems and actuation systems, d A standard formula with its associated design criteria for calculating the steady-state wind stability (i.e., tip point) for aircraft ground support equipment, e A standard method for testing these systems.