Refine Your Search

Topic

Search Results

Technical Paper

Experimental Analysis of the Operating Parameter Influence on the application of Low Temperature Combustion in the Modern Diesel Engines

2007-07-23
2007-01-1839
The present paper describes the effects of some operating parameters on the performance of a single cylinder research engine when it runs under Low Temperature Combustion (LTC) conditions. Aim of the experimental work was to explore the potential of the control of each parameter on the improvement of LTC application to the modern LD diesel engines for passenger cars. In particular, the effects on LTC performance of the following operating parameters in different engine test points were analyzed: intake air temperature, exhaust EGR cooler temperature, intake pipe pressure, exhaust pipe pressure and swirl ratio. Some parameters have shown a particular influence on the improvement of EGR tolerability for maximum NOx reduction preserving fuel consumption and smoke, while others have evidenced poor sensitivity.
Technical Paper

Compression Ratio Influence on the Performance of an Advanced Single-Cylinder Diesel Engine Operating in Conventional and Low Temperature Combustion Mode

2008-06-23
2008-01-1678
The present paper describes a detailed experimental analysis on the effect of the compression ratio on the performance of a single-cylinder research diesel engine operating with both conventional combustion and Low Temperature Combustion mode for low NOx emissions. The single-cylinder engine was developed with the same combustion system architecture of the four-cylinder FIAT 1.9 liter Multi-Jet. Starting from an engine configuration with a compression ratio of 16.5, the compression ratio was reduced to 14.5. For both the geometric configurations, engine performance was evaluated in terms of thermodynamic parameters, emissions and fuel consumption in some operating test points representative of the engine behavior running on the NEDC cycle.
Technical Paper

Implementation and Validation of a n-Heptane Kinetic Combustion Model for 3D-CFD Codes by Means of Numerical Calculations and Single Cylinder Engine Experiments

2009-04-20
2009-01-0708
An integrated numerical-experimental research activity has been carried out, in order to investigate the reliability of a modified, parallel version of KIVA3V, coupled with detailed kinetics, as an additional tool for the analysis of experimental results. In the proposed approach, fixed chemical species included in the reaction mechanism are used as markers for selection of the numerical methods to be used, aiming at exploiting, in every phase of the calculation, the most suitable solver. For validation purposes, pure n-Heptane was chosen as representative fuel model, both in experiments and computations. Calculated values are compared with experimental data collected on a single-cylinder diesel engine fuelled with pure n-heptane, in order to allow the direct use of a reaction mechanism for a single-component fuel.
Technical Paper

Combustion and Emission Characteristics of a Diesel Engine Fuelled with Diesel-LPG Blends

2019-09-09
2019-24-0038
Recently, it has been worth pointing out the relevance of alternative fuels in the improvement of air quality conditions and in the mitigation of global warming. In order to deal with these demands, in recent studies, it has been considered a great variety of alternative fuels. It goes without saying that the alternative fuels industry needs the best of the efficiency with a moderate layout. From this perspective, Liquefied Petroleum Gas (LPG) could represent a valid option, although it is not a renewable fuel. In terms of polluting emissions, the LPG can reduce nitrous oxides and smoke concentrations in the air, a capability that has a relevant importance for the modern pollution legislation. LPG is well known as an alternative fuel for Spark Ignition (SI) engines and, more recently, LPG systems have also been introduced in the Compression Ignition (CI) engines in dual-fuel configuration.
Technical Paper

Parametric Analysis of the Effect of Pilot Quantity, Combustion Phasing and EGR on Efficiencies of a Gasoline PPC Light-Duty Engine

2017-09-04
2017-24-0084
In this paper, a parametric analysis on the main engine calibration parameters applied on gasoline Partially Premixed Combustion (PPC) is performed. Theoretically, the PPC concept permits to improve both the engine efficiencies and the NOx-soot trade-off simultaneously compared to the conventional diesel combustion. This work is based on the design of experiments (DoE), statistical approach, and investigates on the engine calibration parameters that might affect the efficiencies and the emissions of a gasoline PPC. The full factorial DoE analysis based on three levels and three factors (33 factorial design) is performed at three engine operating conditions of the Worldwide harmonized Light vehicles Test Cycles (WLTC). The pilot quantity (Qpil), the crank angle position when 50% of the total heat is released (CA50), and the exhaust gas recirculation (EGR) factors are considered. The goal is to identify an engine calibration with high efficiency and low emissions.
Technical Paper

Analysis of a Prototype High-Pressure “Hollow Cone Spray” Diesel Injector Performance in Optical and Metal Research Engines

2017-09-04
2017-24-0073
Technologies for direct injection of fuel in compression ignition engines are in continuous development. One of the most investigated components of this system is the injector; in particular, main attention is given to the nozzle characteristics as hole diameter, number, internal shape, and opening angle. The reduction of nozzle hole diameter seems the simplest way to increase the average fuel velocity and to promote the atomization process. On the other hand, the number of holes must increase to keep the desired mass flow rate. On this basis, a new logic has been applied for the development of the next generation of injectors. The tendency to increase the nozzle number and to reduce the diameter has led to the replacement of the nozzle with a circular plate that moves vertically. The plate motion allows to obtain an annulus area for the delivery of the fuel on 360 degrees; while the plate lift permits to vary the atomization level of the spray.
Technical Paper

Outward-Opening Hollow-Cone Spray Characterization by Experimental and Numerical Approach in Evaporative and Non-Evaporative Conditions

2017-09-04
2017-24-0108
In the present paper, a new concept of open nozzle spray was investigated as possible application for compression ignition engines. The study concerns an experimental and numerical characterization of a spray generated through a prototype high-pressure hollow-cone nozzle (HCN). The experimental description of the injection process was carried out under evaporative and non-evaporative conditions injecting the fuel in a constant-volume combustion vessel controlled in pressure and temperature in order to measure the spatial and temporal fuel pattern at engine-like gas densities. OpenFOAM libraries in the lib-ICE version of the numerical code were employed for simulating the spray dynamics after a first validation phase based on the experimental data. Results show a typical spray structure of the outward-opening nozzle with the overall fluid-dynamic arrangement having a good fuel distribution along the hollow-cone geometry but showing a reduced spatial penetration.
Technical Paper

How Much Regeneration Events Influence Particle Emissions of DPF-Equipped Vehicles?

2017-09-04
2017-24-0144
Diesel particulate filter (DPF) is the most effective emission control device for reducing particle emissions (both mass, PM, and number, PN) from diesel engines, however many studies reported elevated emissions of nanoparticles (<50 nm) during its regeneration. In this paper the results of an extensive literature survey is presented. During DPF active regeneration, most of the literature studies showed an increase in the number of the emitted nanoparticles of about 2-3 orders of magnitude compared to the normal operating conditions. Many factors could influence their amount, size distribution, chemical-physical nature (volatiles, semi-volatiles, solid) and the duration of the regenerative event: i.e. DPF load and thermodynamic conditions, lube and fuel sulfur content, engine operative conditions, PN sampling and measurement methodologies.
Technical Paper

The Key Role of Advanced, Flexible Fuel Injection Systems to Match the Future CO2 Targets in an Ultra-Light Mid-Size Diesel Engine

2018-05-30
2018-37-0005
The paper describes the results achieved in developing a new diesel combustion system for passenger car application that, while capable of high power density, delivers excellent fuel economy through a combination of mechanical and thermodynamic efficiencies improvement. The project stemmed from the idea that, by leveraging the high fuel injection pressure of last generation common rail systems, it is possible to reduce the engine peak firing pressure (pfp) with great benefits on reciprocating and rotating components light-weighting and friction for high-speed light-duty engines, while keeping the power density at competitive levels. To this aim, an advanced injection system concept capable of injection pressure greater than 2500 bar was coupled to a prototype engine featuring newly developed combustion system. Then, the matching among these features have been thoroughly experimentally examined.
Technical Paper

Assessment of Engine Control Parameters Effect to Minimize GHG Emissions in a Dual Fuel NG/Diesel Light Duty Engine

2018-04-03
2018-01-0266
The interest in Natural Gas (NG) as alternative fuel for transportation is constantly growing, mostly due to its large availability and lower environmental impact with respect to gasoline or diesel fuel. In this scenario, the application of the Dual Fuel (DF) Diesel- Natural Gas (NG) combustion concept to light duty engines can represent an important route to increment the diffusion of natural gas use. Many studies have proven the benefits of DF with respect to conventional diesel combustion in terms of CO2, NOx, PM and PN emissions, with the main drawback of high unburned hydrocarbon, mainly at low/partial engine loads. This last aspect still prevents the application of DF mode to small displacement engines. In the present work, a 2.0 L Euro 5 compliant diesel engine, equipped with an advanced electronic closed-loop combustion control (CLCC) system, has been set up to operate in DF mode and tested on a dyno test bench.
Journal Article

Functional Requirements to Exceed the 100 kW/l Milestone for High Power Density Automotive Diesel Engines

2017-09-04
2017-24-0072
The paper describes the challenges and results achieved in developing a new high-speed Diesel combustion system capable of exceeding the imaginative threshold of 100 kW/l. High-performance, state-of-art prototype components from automotive diesel technology were provided in order to set-up a single-cylinder research engine demonstrator. Key design parameters were identified in terms boost, engine speed, fuel injection pressure and injector nozzle flow rates. In this regard, an advanced piezo injection system capable of 3000 bar of maximum injection pressure was selected, coupled to a robust base engine featuring ω-shaped combustion bowl and low swirl intake ports. The matching among the above-described elements has been thoroughly examined and experimentally parameterized.
Technical Paper

Experimental and Numerical Analysis of a High-Pressure Outwardly Opening Hollow Cone Spray Injector for Automotive Engines

2017-03-28
2017-01-0840
In the aim of reducing CO2 emissions and fuel consumption, the improvement of the diesel engine performance is based on the optimization of the whole combustion system efficiency. The focus of new technological solutions is devoted to the optimization of thermodynamic efficiency especially in terms of reduction of losses of heat exchange. In this context, it is required a continuous development of the engine combustion system, first of all the injection system and in particular the nozzle design. To this reason in the present paper a new concept of an open nozzle spray was investigated as a possible solution for application on diesel engines. The study concerns some experimental and numerical activities on a prototype of an open nozzle. An external supplier provided the prototypal version of the injector, with a dedicated piezoelectric actuation system, and with an appropriate choice of geometrical design parameters.
Technical Paper

Application of a Dual Fuel Diesel-CNG Configuration in a Euro 5 Automotive Diesel Engine

2017-03-28
2017-01-0769
An increasing interest in the use of natural gas in CI engines is currently taking place, due to several reasons: it is cheaper than conventional Diesel fuel, permits a significant reduction of carbon dioxide and is intrinsically clean, being much less prone to soot formation. In this respect, the Dual Fuel concept has already proven to be a viable solution, industrially implemented for several applications in the heavy duty engines category. An experimental research activity was devoted to the analysis of the potentiality offered by the application of a Dual Fuel Diesel-CNG configuration on a light duty 2L Euro 5 automotive diesel engine, equipped with an advanced control system of the combustion. The experimental campaign foresaw to test the engine in dynamic and steady state conditions, comparing engine performance and emissions in conventional Diesel and Dual Fuel combustion modes.
Technical Paper

Parametric Analysis of Compression Ratio Variation Effects on Thermodynamic, Gaseous Pollutant and Particle Emissions of a Dual-Fuel CH4-Diesel Light Duty Engine

2017-03-28
2017-01-0764
The paper reports the results of an experimental campaign aimed to assess the impact of the compression ratio (CR) variation on the performance and pollutant emissions, including the particle size spectrum, of a single cylinder research engine (SCE), representatives of the engine architectures for automotive application, operated in dual-fuel methane-diesel mode. Three pistons with different bowl volumes corresponding to CR values of 16.5, 15.5 and 14.5 were adopted for the whole test campaign. The injection strategy was based on two injection pulses per cycle, as conventionally employed for diesel engines. The test methodology per each CR included the optimization of both 1st injection pulse quantity and intake air mass flow rate in order to lower as much as possible the unburned methane emissions (MHC).
Journal Article

Impact of RME and GTL Fuel on Combustion and Emissions of a “Torque-Controlled” Diesel Automotive Engines

2010-05-05
2010-01-1477
The present paper describes some results of a research project aimed at studying the impact of alternative fuels blends on the emissions and fuel consumption of an Euro 5 automotive diesel engine. Two alternative fuels were chosen for the experiments: RME and GTL. The tests were done in the three most important operating conditions for the engine emission calibration. Moreover, the NOx-PM trade-off by means of EGR sweep was performed in the same operating conditions, in order to evaluate the engine EGR tolerability when burning low sooting fuels as the RME. The investigations put in evidence that the impact of the alternative fuels on modern diesel engines remains significant. This also depends on the interaction between the alternative fuel characteristics and the engine-management strategies, as described in detail in the paper.
Journal Article

Experimental Investigation of the Benefits of Cooled and Extra-cooled Low-Pressure EGR on a Light Duty Diesel Engine Performance

2009-09-13
2009-24-0126
The present paper describes an experimental study on the application of a Low Pressure EGR system, equipped with an high efficiency cooler, to a LD diesel engine operating with both conventional combustion and PCCI mode. The research activity is aimed to carry out an analysis of the potentiality of the cooling (with engine water at 90°C) and super-cooling (with external water at 20°C) of the low pressure EGR flow gas on the simultaneous reduction of fuel consumption and pollutant emissions. The effects were evaluated running the engine with diesel conventional combustion and PCCI mode in several engine operating points. The employed engine was a 4-cyliders LD CR diesel engine of two liters of displacement at the state of art of the current engine technology. The overall results identified benefits on both the fuel consumption and emissions with the use of a low pressure EGR system with respect to the “classical” high pressure EGR one.
Journal Article

Alternative Diesel Fuels Effects on Combustion and Emissions of an Euro4 Automotive Diesel Engine

2009-09-13
2009-24-0088
The present paper describes the first results of a cooperative research project between GM Powertrain Europe and Istituto Motori of CNR aimed at studying the impact of Fatty-Acid Methyl Esters (FAME) and gas-to-liquid (GTL) fuel blends on the performance, emissions and fuel consumption of modern automotive diesel engines. The tests were performed on the architecture of GM 1.9L Euro4 diesel engine for passenger car application, both on optical single-cylinder and on production four-cylinder engines, sharing the same combustion system configuration. Various blends of biodiesels as well as reference diesel fuel were tested. The experimental activity on the single-cylinder engine was devoted to an in-depth investigation of the combustion process and pollutant formation, by means of different optical diagnostics techniques, based on imaging multiwavelength spectroscopy.
Technical Paper

Multidimensional Simulations of Combustion in Methane-Diesel Dual-Fuel Light-Duty Engines

2017-03-28
2017-01-0568
The adoption of gaseous fuels for Light Duty (LD) engines is considered a promising solution to efficiently reduce greenhouse gases emissions and diversify fuels supplies, while keeping pollutants production within the limits. In this respect, the Dual Fuel (DF) concept has already proven to be, generally speaking, a viable solution, industrially implemented for several applications in the Heavy-Duty (HD) engines category. Despite this, some issues still require a technological solution, preventing the commercialization of DF engines in wider automotive fields, including the release of high amounts of unburned species, possibility of engine knock, chance of thermal efficiency reduction. In this framework, numerical simulation can be a useful tool, not only to better understand specific characteristics of DF combustion, but also to explore specific geometrical modifications and engine calibrations capable to adapt current LD architectures to this concept.
Technical Paper

Hydrocracked Fossil Oil and Hydrotreated Vegetable Oil (HVO) Effects on Combustion and Emissions Performance of “Torque-Controlled” Diesel Engines

2015-09-06
2015-24-2497
The present paper describes the results of a research activity aimed at studying the potential offered by the use of Hydrocracked fossil oil (HCK) and Hydrotreated Vegetable Oil (HVO) blends as premium fuels for next generation diesel engines. Five fuels have been tested in a light duty four cylinder diesel engine, Euro 5 version, equipped with closed loop control of the combustion. The set of fuels comprises four experimental fuels specifically formulated by blending high cetane HVO and HCK streams and oneEN590-compliant commercial diesel fuel representative of the current market fuel quality. A well consolidated procedure has been carried out to estimate, for the tested fuels, the New European Driving Cycle (NEDC) vehicle performance by means of the specific emissions at steady-state engine operating points.
Technical Paper

Characterization of Combustion and Emissions in Light-Duty Diesel Engines Using High-Glycerol-Ethers/Diesel Blends

2015-09-06
2015-24-2445
In this paper, a detailed analysis of combustion and emissions is carried out on both metal and optical light duty diesel engines equipped with up-to-date combustion architecture. Both engines were fed with glycerol ethers mixture (GEM) in blend (10% and 20% v/v) within a commercial diesel fuel. The engines ran in significant operating points in the NEDC (New European Driving Cycle) emission homologation area. The results of the experimental campaign on the metal engine show comparable performances between the diesel/GEM blends and the diesel fuel and demonstrate benefits mainly in terms of soot production. The exhaust particles diameters of diesel/GEM blends shift toward smaller dimensions and the total number decreases. Moreover, at lower load conditions, the outputs show a worsening of the unburnt mainly ascribable to the fuel characteristics.
X