Search Results

Measurement of emissions from small utility engines has usually been accomplished using steady-state raw emissions procedures such as SAE Recommended Practice J1088. While raw exhaust measurements have the advantage of producing modal exhaust gas concentration data for design feedback; they are laborious, may influence both engine performance and the emissions themselves, and have no provision for concurrent particulate measurements. It is time to consider a full-dilution procedure similar in principle to automotive and heavy-duty on-highway emission measurement practice, leading to improvements in many of the areas noted above, and generally to much higher confidence in data obtained. When certification and audit of small engine emissions become a reality, a brief dilute exhaust procedure generating only the necessary data will be a tremendous advantage to both manufacturers and regulatory agencies.

Several properties of a refinery “straightrun kerosene“, which had a narrow boiling range approximating the middle of a No. 1 diesel fuel, were altered to study their effects on regulated and unregulated exhaust emissions. Eleven fuel blends, representing changes in nitrogen content, aromatic level, boiling point distribution, olefin content, and cetane number, were evaluated in a 1975 Mercedes-Benz 240D. Statistical analysis, including regression, was performed using selected fuel properties as independent variables. Higher aromatic levels were generally associated with increased emissions, while increased olefin levels were generally associated with decreased emissions.

Regulated gaseous, particulate and several unregulated emissions are reported from four heavy-duty diesel engines operated on the chassis version of the 1983 transient procedure. Emissions were obtained from Caterpillar 3208, Mack ENDT 676, Cummins Formula 290 and Detroit Diesel 8V-71 engines with several diesel fuels. A large dilution tunnel (57′ × 46″ ID) was fabricated to allow total exhaust dilution, rather than the double dilution employed in the stationary engine version of the transient procedure. A modal particulate sampler was developed to obtain particulate data from the individual segments of the 1983 transient procedure. The exhaust gas was analyzed for benzo(a)pyrene, metals, N2O, NO2, individual hydrocarbons and HCN. Sequential extractions were performed and measured versus calculated fuel consumptions were obtained.

In an attempt to characterize emissions from small air-cooled utility engines, five gasoline-fueled models were operated over a variety of speeds and loads, and important exhaust constituents were measured. These emissions included hydrocarbons, CO, CO2, NO, O2, aldehydes, light hydrocarbons, particulates, and smoke. Emissions of SOx were estimated on the basis of the fuel consumed; evaporative losses of hydrocarbons were also estimated. The impact of small engine emissions was calculated on the basis of the test results and information on national engine populations and usage. From these data, it appears that the 50 million or more small engines currently being used account for only a small part of pollutants from all sources.

The research program on which this paper is based included both laboratory emission measurements and extrapolation of results to the national population of heavy-duty farm, construction, and industrial engines. Emission tests were made on four gasoline engines and eight diesel engines typical of those used in F, C, and I equipment. Gaseous and particulate emissions were measured during engine operation on well-accepted steady-state procedures, and diesel smoke was measured during both steady-state conditions and the Federal smoke test cycle. Emissions measured were hydrocarbons, CO, CO2, NO, NOx, O2, aliphatic aldehydes, light hydrocarbons, particulate, and smoke. Emission of sulfur oxides (SOx) was estimated on the basis of fuel consumed, and both evaporative and blowby hydrocarbons were also estimated where applicable (gasoline engines only). Data on emissions obtained from this study were compared with those available in the literature, where possible.

The gaseous and particulate emissions from a light-duty diesel powered passenger car were measured by a variety of chemical analysis techniques for three different fuels, typical No. 1 and No. 2 commercial diesel fuels and the Federal Register No. 2-D smoke test fuel. Hydrocarbon emissions were found to be inversely related to fuel molecular weight. The NO2/NO ratio was found to be much higher than for gasoline engines approaching 0.3 at low load. Particulate emissions were approximately 0.3 grams/mile for all fuels and driving cycles tested. Sulfate emissions were high, approaching that of some catalyst cars. Sulfate emissions decreased with decreasing fuel sulfur and increased by a factor of two in highway driving over urban driving. The potential pollution problems with such cars are worthy of further study.

This paper describes the results of a public opinion survey on testing of diesel exhaust odors conducted during 1969 and 1970. Major goals of the research were to relate public opinion of the odors and the objectionability associated with them to odor intensity, and to obtain a dose-response curve as the primary result. The dose-response curve was needed to assess odor-control technology by providing a criterion for deciding whether or not the effect of a given control item would be noticed by the general public, reduce complaints, or be worth the cost and effort required for its implementation. The engine used as the live odor source for the subject research was a two-stroke cycle type similar to those used in many buses. This engine type was chosen because its exposure to the public in urban bus applications is very widespread, and because a large portion of the Environmental Protection Agency's odor research had been performed with similar engines.

Seven motorcycles, ranging in size from 100 to 1200 cm3, were tested for emissions characterization purposes. They were operated on the federal seven-mode test procedure (for 1971 and older light-duty vehicles), the federal LA-4 test procedure (for 1972 and later LDVs), and under a variety of steady-state conditions. Four of the machines tested had 4-stroke engines, and the other three had 2-stroke engines. Emissions which were measured included hydrocarbons, CO, CO2, NO, NOx, O2, aldehydes, light hydrocarbons, particulates, and smoke. Emissions of SOx were estimated on the basis of fuel consumed, and evaporative hydrocarbon losses were also estimated. Crankcase “blowby” emissions from one 4-stroke machine were measured. The impact of motorcycles on national pollutant totals was estimated, based on the test results and information from a variety of sources on national population and usage of motorcycles.

This paper describes a research program on exhaust emissions from snowmobile engines, including both emissions characterization and estimation of national emissions impact. Tests were conducted on three popular 2-stroke twins and on one rotary (Wankel) engine. Emissions that were measured included total hydrocarbons, (paraffinic) hydrocarbons by NDIR, CO, CO2, NO (by two methods), NOx, O2, aldehydes, light hydrocarbons, particulate, and smoke. Emissions of SOx were estimated on the basis of fuel consumed, and evaporative hydrocarbons were projected to be negligible for actual snowmobile operation. During emissions tests, intake air temperature was controlled to approximately -7°C (20°F), and room air at approximately 24°C (75°F) was used for engine cooling. Based on test results and the best snowmobile population and usage data available, impact of snowmobile emissions on a national scale was computed to be minimal.

To characterize exhaust emissions from water-cooled 2-stroke outboard motors (the predominant type), four new motors were tested on dynamometer stands. The engines ranged from 4-65 hp in size, and operating conditions were chosen along lines of simulated boat loading. All the measurements were taken at steady-state conditions. Emission concentrations were measured in raw exhaust gas and after the gases had been bubbled through water in a specially constructed tank. Constituents measured included hydrocarbons, CO, CO2, NO, NOx, O2, light hydrocarbons, and aldehydes. Emissions of sulfur oxides (SOx) were estimated on the basis of fuel consumed, and all the exhaust emissions data were used with available information on population and usage of motors to estimate exhaust emission factors and national exhaust emissions impact.

Particulate and gaseous emissions from two light-duty diesel vehicles were measured over eight operating schedules, using five different fuels. Characterization included regulated exhaust emissions and a number of unregulated constituents. Non-routine gas measurements included phenols, hydrocarbon boiling range, and aldehydes. Particulate characterization included mass rates and concentrations, visible smoke, aerodynamic sizing, total organics, BaP, sulfate, phenols, trace elements, and major elements. Statistical analysis of emissions data was undertaken using fuel properties and operating schedule statistics as independent variables. Regressions were computed for a few variables, and analysis of variance and multiple comparisons were used where the data were not suitable for regression analysis.

Gaseous and particulate emissions from two heavy-duty diesel engines were characterized while the engines were operated on five different fuels. Characterization included mass rates of major exhaust products, plus analysis of particulate matter for sulfate, trace elements, major elements, total solubles, and other properties. Analysis of rate and composition data was conducted with regard to fuel and engine effects on particulate. Two large particulate samples were also collected for later analysis on groups of organics present.

Emissions from two heavy-duty four stroke direct injection engines designed to use methanol fuel, one using Diesel pilot fuel injection and the other using spark ignition, were characterized in this program along with those from a comparably-sized Diesel engine. Emissions evaluated during both steady-state and transient FTP procedures included regulated gases (HC, CO, and NOx), unburned methanol, aldehydes, other gaseous organics, total particulate, sulfate, soluble organics in particulate and BaP. The engines adapted for methanol fuel and using catalysts emitted less HC, CO, particulate, soluble organics, and BaP than the Diesel fueled engine.

The possibility that NO2 artifactually converts polynuclear aromatic hydrocarbons to biologically active species in diesel particle sampling is explored. NO2 was injected into dilution air upstream of the exhaust mixing point at varvinq concentra-ting levels with both passenger car and truck driving simulations. Ames test specific activity and nitropyrene levels were seen to increase above base levels when the NO2 level exceeded 5 to 10 ppm. Extract responses to added NO2 in transient drivinq appeared to initially increase, then level off above about 20 ppm. It is suggested that some requestering of nitratable orqan-ics may be responsible. Reexposure of filtered particles to diluted gas phase diesel exhaust caused little increase in nitroaromatics or Ames activitv. It appears that NO2 levels below about 5 ppm are relatively safe from filter artifacts.

Ethylene dibromide, a suspected carcinogen, and ethylene dichloride are commonly used in leaded gasoline as scavengers. Ethylene dibromide emission rates were determined from seven automobiles which had a wide range of control devices, ranging from totally uncontrolled to evaporative and catalytic emission controls. The vehicles were operated over a variety of cycles to simulate the normally encountered range of driving conditions. Evaporative losses were also measured. Tailpipe emission rates varied from 0 to 1300 micrograms ethylene dibromide per mile depending upon the control devices present and the operating cycle. Evaporative emission of ethylene dibromide ranged from 0.03 to 0.4 micrograms per mile equivalent. Emission of other lead-related compounds were sought but not found. The consequences of using leaded fuels in vehicles equipped with catalysts was investigated. Emission rates of ethylene dibromide increased with usage and appeared to depend on catalyst activity.

Emissions from a modern heavy-duty Diesel truck engine were characterized with five different fuels during transient and steady-state operation. A control fuel (Phillips D-2) was used for baseline emissions, and as base stock in three alternate fuel blends containing EDS or SRC-II middle distillates, or used lubricating oil. The fifth fuel tested was neat soybean oil, heated to 145°C. HC, CO, NOX, and particulate emissions were similar for this engine on all fuels tested, with the exception of higher particulates for the soybean oil and higher NOX for the SRC-II blend.

Exhaust emission data from several fuel effects studies were normalized and subjected to statistical analyses. The goal of this work was to determine whether emission effects of property variation in alternate-source fuels were similar, less pronounced, or more pronounced than the effects of property variation in petroleum fuels. A literature search was conducted, reviewing hundreds of studies and finally selecting nine which dealt with fuel property effects on emissions. From these studies, 15 test cases were reported. Due to the wide variety of vehicles, fuels, test cycles, and measurement techniques used in the studies, a method to relate them all in terms of general trends was developed. Statistics and methods used included bivariate correlation coefficients, regression analysis, scattergrams and goodness-of-fit determinations.

Diesel soot or smoke has been regarded as a nuisance pollutant and potential health hazard, especially in congested urban areas where diesel buses operate. Exhaust emissions from a DDAD 6V-71 coach engine and a similarly-powered 1980 GMC RTS-II coach, fitted with a non-catalyzed particulate trap, were characterized over various Federal Test Procedures for heavy-duty engines, including an experimental test cycle for buses. Regeneration was accomplished using an in-line burner in the exhaust to raise the engines' idle exhaust gas temperature from 120 to 700°C. Trap testing included approximately 15 hours of engine operation and 100 miles of bus operation. Particulate emissions were reduced by an average of 79 percent and smoke emissions were nil using the trap. The effect of the trap on regulated and other unregulated emissions was generally minimal.

Diesel engines are adjusted to manufacturers' specifications when produced and placed in service, but varying degrees of maintenance and wear can cause changes in engine performance and exhaust emissions. Maladjustments were made on two heavy-duty diesel engines typically used in buses in an effort to simulate some degree of wear and/or lack of maintenance. Emissions were characterized over steady-state and transient engine operation, in both baseline and maladjusted configurations. Selected maladjustments of the Cummins VTB-903 substantially increased HC, smoke and particulate emission levels. Maladjustments of the Detroit Diesel 6V-71 coach engine resulted in lower HC and NOX emission levels, but higher CO emissions, smoke, and particulate.

Methods for measurement and expression of crankcase or “blowby” emissions from diesels were developed and demonstrated on a test engine. These methods were subsequently used to characterize gas and particulate emissions from two in-service engines. Crankcase emissions were evaluated under engine operating conditions corresponding to the EPA 13-mode certification test. Substances for which analyses were conducted included regulated pollutants, sulfate, trace elements, nitrosamines, individual hydrocarbons, and aldehydes. Emissions from the diesel crankcases were compared to exhaust emissions (where possible) to assess their importance. Analysis for nitrosamines was continued beyond the original effort, utilizing another test engine.