Search Results

Forthcoming emissions legislation is driving the passenger car manufacturers towards the fitting of Diesel Particulate Filters (DPFs) as original equipment. In areas with a particular problem such as heavily congested city centres, retrospective legislation has also been introduced, for example in Hong Kong and Tokyo. Legislation mandating the retrofitting of DPFs obviously has an immediate effect on particulate emissions. Other authorities are thus investigating the efficacy of such measures. However with the increasing use of DPF technology concerns are now being raised over some currently unregulated emissions such as ultra fine particulate and NO2, although total particulate mass and oxides of nitrogen are regulated. To add to the data base for such issues a programme of work was run using London Black Cabs. Four cars were fitted with a DPF, an on-board dosing system to meter a fuel borne catalyst (FBC) into the fuel and a data logger to monitor the DPF performance.

Forthcoming emissions legislation is driving the passenger car manufacturers towards the fitting of Diesel Particulate Filters (DPFs) as original equipment. However such initiatives are not retrospective and due to the replacement rate of the vehicle fleet, there is a time lag before the full benefit of the new measures are fully realised. To overcome this drawback, in areas with a particular problem such as heavily congested city centres, retrospective legislation has been introduced, for example in Hong Kong and Tokyo. Legislation mandating the retrofitting of DPFs obviously has an immediate effect on particulate emissions. Other authorities are thus investigating the efficacy of such measures. To add to the data base for such assessments Octel is running a demonstration programme using London Black Cabs. Four cars have been fitted with a DPF, an on-board dosing system to meter a fuel borne catalyst (FBC) into the fuel and a data logger to monitor the DPF performance.

Future emissions limits are pushing vehicle manufacturers towards the fitting of Diesel Particulate Filters (DPFs) as original equipment. However due to the replacement rate of the vehicle fleet, there is a delay before the full benefit of these measures are fully realised. To overcome this problem, in areas with a particular problem such as heavily congested city centres, retrospective legislation has been, and may be introduced. Legislation mandating the retrofitting of DPFs obviously has an immediate effect on particulate emissions. In some countries including the UK there are also fiscal incentives to fit DPFs. Due to its duty cycle the London taxi or Black Cab is one of the more challenging areas of application for the DPF. Previous work has shown that the use of a fuel borne catalyst (FBC) can extend the operating range of DPF systems providing the possibility of a viable system for such applications.

The influence of swirl on performance and emissions was investigated using a single cylinder Hydra research engine fitted with a high pressure electronic unit injector and a variable swirl mechanism. A large amount of emission data was collected together with the cylinder pressure, fuel line pressure and needle lift signals at a wide range of operating conditions. The influence of a fixed swirl ratio on emissions was also investigated on a Ford HSD425 York engine with conventional injection system and a synopsis of the results is discussed. Laser illuminated high speed cinematography was used to study the interaction of swirl with spray and combustion processes. Data is presented on air- fuel mixing, spray trajectories and flame movement at different operating conditions. Data is also presented to highlight the influence of swirl on the heat release rate, cylinder pressure rise and its relation to measured emission levels, particularly NOx and particulates.

The atomisation characteristics of DI diesel engine fuel injection nozzles have been the subject of intensive study over the last decade. Much of this work has been related to clean, single hole nozzles spraying into quiescent air, at either ambient conditions or elevated pressures and temperatures. Experience shows that fuel injector nozzles may foul very rapidly in field service, and that this might have a significant effect on the performance of the engine particularly with regard to emissions. The build up of material on the injector nozzle can be controlled by the addition of suitable fuel additives. This paper describes test procedures developed to assess deposit build up and to indicate the efficacy of keep clean additives. The paper then goes on to describe high speed photographic techniques for studying the fuel spray characteristics of clean and fouled injectors in a firing engine.

Heat release data have been obtained from a 5 in bore direct injection diesel engine operating over a range of conditions including off-design conditions, such as running at low air to fuel ratios, using six-hole injector nozzles in place of the standard three-hole nozzles, and reducing compression ratio and thereby swirl ratio at tdc. The paper shows that when operating with adequate utilized air fuel ratios (A/Fs) the experimental heat release data could be correlated with a single zone combustion model and that changing the number of nozzle holes or compression/swirl ratio had little effect on the correlation after the initial period of heat release. At inadequate A/Fs a modification to the model to allow for partial combustion was introduced. This improved correlation and enabled reasonable heat release prediction in the cycle synthesis program. Examples are given of heat release and cycle pressure diagrams computed using these models.

The design and application of a high speed, timed, sampling valve for the extraction of gas samples, at a variety of points and times, from the combustion chamber of a medium speed diesel engine is described. The valve was traversed radially into the combustion chamber and combined with rotation of the central fuel injector gave sampling at sixteen points relative to the fuel spray. For any given sample the valve opened and closed at the same time each cycle. Samples were analysed and the levels of carbon monoxide, carbon dioxide and nitric oxide were recorded for the complete combustion process.

Transport Refrigeration Units (TRU) powered by small diesel engines emit high PM and cause locally high PM levels. The concomitant health risks spurred efforts to devise a cost-effective curtailment of these emissions. Diesel particulate filters (DPF) of ceramic honeycomb construction very efficiently trap PM emissions, even ultrafines in the lung penetrating size range of below 300 nm. A fuel borne catalyst (FBC) can facilitate trap regeneration, by lowering the exhaust temperature requirements, but cannot alone guarantee reliable regeneration under all operating conditions of the TRU. A Swiss development team together with industrial partners therefore developed a fully automatic active regeneration system for the California Air Resources Board.