Refine Your Search

Topic

Search Results

Standard

Rod Ends and Clevis Pins

1961-06-01
HISTORICAL
J493_196106
Material--SAE 1010 or SAE 1111 steel or equivalent. Clevis pins shall be supplied either soft or cyanide hardened as specified. Clevis pins must be free from burrs, loose scale, sharp edges, and all other defects that might affect their serviceability. General tolerances for all dimensions are plus or minus 0.010 unless otherwise specified.
Standard

Grooved Straight Pins

1964-06-01
HISTORICAL
J494_196406
Material-Cold drawn SAE 1112 or 1113 steel, alloy steel or copper alloy as specified by purchaser. Unless otherwise specified, steel pins shall have a flash plate of cadmium or zinc for protection of pins in transit or storage. Grooved Straight Pins must be free from burrs and all other defects that might affect their use and serviceability.
Standard

Grooved Straight Pins

2004-05-12
CURRENT
J494_200405
Material-Cold drawn SAE 1112 or 1113 steel, alloy steel or copper alloy as specified by purchaser. Unless otherwise specified, steel pins shall have a flash plate of cadmium or zinc for protection of pins in transit or storage. Grooved Straight Pins must be free from burrs and all other defects that might affect their use and serviceability.
Standard

Hexagon High Nuts

2013-04-15
HISTORICAL
J482_201304
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard

Hexagon High Nuts

2006-04-17
HISTORICAL
J482_200604
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ANSI/ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard

Round Head Bolts

1990-01-01
CURRENT
J481_199001
Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.
Standard

Hexagon High Nuts

1998-05-01
HISTORICAL
J482_199805
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ANSI/ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard

Slotted and Recessed Head Screws

1990-01-01
CURRENT
J478_199001
Included herein are complete general and dimensional data for the types of slotted and recessed head machine, tapping, and wood screws, and slotted capscrews recognized as SAE Standard. Also included are performance data for tapping screws and appendixes which provide instructions for protrusion gaging flat heads, penetration gaging of recessed heads, across corners gaging of hexagon heads, recommended hole sizes for tapping screws, and a cross reference of tapping screw type designations. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumer interests are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

Slotted and Recessed Head Screws

1962-06-01
HISTORICAL
J478A_196206
Included herein are complete general and dimensional data for the types of slotted and recessed head machine, tapping, and wood screws, and slotted capscrews recognized as SAE Standard. Also included are performance data for tapping screws and appendixes which provide instructions for protrusion gaging flat heads, penetration gaging of recessed heads, across corners gaging of hexagon heads, recommended hole sizes for tapping screws, and a cross reference of tapping screw type designations. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumer interests are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

Cotter Pins

1990-01-01
CURRENT
J487_199001
Not available.
Standard

Lock Washers

1974-02-01
HISTORICAL
J489B_197402
Not available.
Standard

Hexagon High Nuts

2016-11-18
CURRENT
J482_201611
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard

Alignment of Nut Slots

1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

1998-05-01
HISTORICAL
J485_199805
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
Standard

Conical Spring Washers

1976-02-01
HISTORICAL
J773B_197602
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies. Both the type L and type H washers are available in three washer series (narrow, regular and wide), having varied proportions designed to fulfill specific application requirements for load distribution. Where so specified by the user, washers shall be supplied with peripheral teeth. All sizes and types of washers specified in this standard are not necessarily stock production items. Users should consult with manufacturers concerning availability.
X