Search Results

An experimental study has been carried out to assess the capability of injecting vaporised fuel into the exhaust gas of a diesel engine to achieve elevated outlet temperatures from an oxidation catalyst for the thermal regeneration of particulate filters. Termed catalytic combustion and passive in nature, controlled experiments have proved the concept with the limitation on catalyst outlet temperature being dictated by the material limits of the exhaust system and the availability of oxygen.

Validation of the Ford General Engine SIMulation program (GESIM) with measured firing data from a modified single cylinder Ricardo HYDRA research engine is described. GESIM predictions for peak cylinder pressure and burn duration are compared to test results at idle operating conditions over a wide range of valve overlap. The calibration of GESIM was determined using data from only one representative world-wide operating point and left unchanged for the remainder of the study. Valve overlap was varied by as much as 36° from its base setting. In most cases, agreement between model and data was within the accuracy of the measurements. A cycle simulation computer model provides the researcher with an invaluable tool for acquiring insight into the thermodynamic and fluid mechanical processes occurring in the cylinder of an internal combustion engine.

Feasibility of wall-flow diesel exhaust filter trap particulate aftertreatment emission control systems to meet the U.S. Federal, CARB, and EC passenger car standards for 1997/2003 and beyond for the 1360 kg (3000 lb.) EAO (Ford European Automotive Operations) 1.8 liter Sierra Turbo-Diesel passenger car is investigated. Plain and Pd catalyzed monolith wall flow diesel particulate traps are examined using Phillips No. 2 diesel fuel (Reference Standard), low sulfur (0.05% S) diesel fuel and an ultra-low sulfur (0.001% S) diesel fuel. Comparisons are made with baseline FTP75 and Highway exhaust emissions and Federal and CARB mandated particulate standards for 1997 and 2003. Effectiveness of catalyzed traps, plain traps, copper octoate trap regeneration fuel additive, and fuel sulfur content on the particulate emissions is determined.

This paper recounts a brief history of Ford high speed direct injection (HSDI) diesel engines; from the original 2.5 litre naturally aspirated (NA) engine introduced 10 years ago as the world's first high volume HSDI diesel, followed by the introduction of the turbocharged version in 1992 with drive-by-wire electronic fuel injection pump, to the latest low emission version developed to meet recent European Commission (EC) “Stage 2” 94/12/EC standards. The performance development of a prototype 4-valve per cylinder version of the 2.5 litre engine is briefly described, covering the fuel injection equipment, exhaust gas recirculation (EGR) tolerance, regulated emissions capability including the important oxides of nitrogen (NOx) and particulates trade-off, and the performance potential of this combustion system.

A 1.8L turbocharged diesel engine valvetrain friction was investigated, and the effectiveness of using a solid film lubricant (SFL) coating in reducing friction was determined throughout the operable speed range. This valvetrain design features direct acting mechanical bucket valve lifters. Camshaft journal bearing surfaces and all camshaft rubbing surfaces except lobe tips were coated. The direct acting bucket shims were etched with a cross hatch pattern to a depth sufficient to sustain a SFL film coating on the shim rubbing surfaces subjected to high surface loads. The SFL coated valvetrain torque was evaluated and compared with uncoated baseline torque. Coating the cam bearing journal surfaces alone with II-25D SFL reduced valvetrain friction losses 8 to 17% for 250 to 2000 rpm cam speed range (i.e. 500 - 4000 rpm engine speed). When bucket tappet and shims were also coated with the SFL, further significant reductions in coated valvetrain friction were observed.

A computer model solving the 1-D flow in a typical fuel injection system for direct-injection diesel engines is presented. A Bosch distributor - type VE pump connected to four Stanadyne pencil - type nozzles has been used to validate the computer model over a wide range of operating conditions. Validation of the developed computer code has been performed for eight representative test cases. The predicted values which were compared with the experimental ones include the pumping chamber pressure, the line pressure, the needle lift and the injection rate. Results using as input the measured pumping chamber pressure are also presented in order to identify the error in the injection rate signal attributed to the difference between the simulated and the experimental pumping chamber pressure. In addition, the total fuel injection quantity for pump speeds between 500 and 2000 rpm and lever positions between 20% to 100% was calculated and compared with measurements.

The regulated and non-regulated emissions of a current diesel passenger car and two light-duty diesel trucks with catalysts and particulate traps were measured to better understand the effects of aftertreatment devises on the environment. The passenger car, a 1.8 L IDI TC Sierra, was tested both with and without three different diesel oxidation catalysts (DOC) and with two fuel sulfur levels, 0 and 0.05 wt%. One light-duty truck, a 2.5 L DI NA Transit, was tested on one fuel, 0.05 wt% sulfur, with and without three different particulate trap/regeneration systems and with and without a urea lean NOx catalyst (LNC) system. A second similar Transit was tested on the 0.05 wt% sulfur fuel with an electrically regenerated trap system. The results are compared to each other, regulated emission standards, and to emissions from gasoline vehicles.

The development, evaluation, and selection of Plasma spray powder material for the coating of aluminum-alloy engine cylinder block bores was conducted to yield a bore system which provides numerous benefits relative to the present cast iron sleeve system. These include: a reduction in ring/bore wear, friction, and in engine oil consumption as well as a benefit in reduced corrosion. A reduction in engine weight, overall costs, and improvements in machining and honing operations are shown. Alternate thermal spray processes are also described in this investigation. Test evaluation leads to the selection of two plasma powder material spray systems. One system emphasizes low cost relative to the present system. The second system provides significant reduction in friction and ring/bore wear through the introduction of solid lubricant in the material composition.

An extremely tough alumina based ceramic coating produced by a modified anodizing process developed at Moscow Aviation Institute has been evaluated for light weight, wear resistant component applications in automotive powertrain. The process details and test results from comparative evaluation of friction and wear properties for cylinder bore application, referenced to cast iron baseline, are presented and discussed.

Advanced techniques for regenerating diesel particulate traps are described. A bypassable trap system minimized regeneration thermal energy requirements. Thermal regeneration systems with burners or electric resistance heaters were evaluated. Regeneration emissions and fuel consumption penalties were measured. Catalytic fuel additives consisting of octoate based compounds of copper and nickel, and copper and cerium provided reductions of up to 410°F in trap regeneration temperature. Durability tests confirmed frequent self regeneration with fuel additives. Over 95% of the fuel additive was collected by the trap. The useful life of the trap having a volume equal to engine displacement was estimated to be 30,000 miles.

Thermal and catalytic techniques for regenerating particulate traps were assessed. The thermal technique used a burner which heated engine exhaust to the ignition temperature of the particulates to achieve over 90% regeneration effectiveness. HC, CO and particulate emissions resulting from combustion of particulates and burner exhaust were 25 to 50% of the allowable vehicle emissions for one CVS cycle. The fuel consumed by the burner was 9% of the fuel consumed by a vehicle over one CVS cycle. Problems with burner nozzle clogging, ignition reliability, trap durability and control system requirements were identified. In the catalytic technique, Diesel fuel containing .5 gm/gal lead and .25 gm/gal copper lowered the ignition temperature of the particulates by 425°F so that periodic regeneration occurred. The trap collected nearly all of the lead and copper resulting in limited trap life, and deposits on the engine fuel nozzles tended to increase HC emissions.

Many Diesel engine development programs concentrate almost exclusively on steady state investigations to benchmark an engines performance. In reality, the inter-action of an engine's sub-systems under transient evaluation is very different from that evident during steady state evaluation. The transient operation of a complete engine system is complex, and collecting test data is very demanding, requiring sophisticated facilities for both control and measurement. This paper highlights the essential characteristics of a Diesel engine when undertaking testbed transient manouevres. Results from simple transient sequences typical of on-road operation are presented. The tests demonstrate how transient behaviour of the engine deviates greatly from the steady state optimum settings used to control the engine.

The use of variable geometry turbocharging (VGT) as an aid to performance enhancement has been the subject of much interest for use in high-speed, light-duty automotive diesel applications in recent times (4). One of the key benefits anticipated is the improved transient response possible with such a device over the conventional fixed geometry turbine with wastegate. The transient responses of two different types of variable geometry turbocharger have been investigated on a dynamic engine test bed. To demonstrate the effect of the turbocharger on the entire system a series of step changes in engine load at constant engine speed were carried out with the turbocharger and exhaust gas recirculation (EGR) systems under the control of the engine management microprocessor. Results are presented which compare the different performance and emissions characteristics of the devices. Some control issues are discussed with a view to improving the transient response of both types.

The findings presented in this paper are part of a long term project aimed at raising the science of heat transfer in internal combustion engine cooling galleries. Initial work has been undertaken by the authors and an experimental facility is able to simulate different sizes of coolant passages. External heat is applied and data for the forced convective, nucleate boiling and transition or critical heat flux (CHF) regimes has been obtained. The results highlighted in this paper attempt to quantify the effects of cooling passage surface roughness on the nucleate boiling regime. Tests have been conducted using aluminium test pieces with surface finishes described as smooth, intermediate and as-cast. It has been found that the as-cast surface increases the heat flux density in the nucleate boiling region over that of the smooth and intermediate surfaces.