Search Results

This article presents an investigation of the sources combustion-generated noise and its measurement in HCCI engines. Two cylinder-pressure derived parameters, the Combustion Noise Level (CNL) and the Ringing Intensity (RI), that are commonly used to establish limits of acceptable operation are compared along with spectral analyses of the pressure traces. This study focuses on explaining the differences between these two parameters and on investigating the sensitivity of the CNL to the ringing/knock phenomenon, to which the human ear is quite sensitive. Then, the effects of independently varying engine operating conditions such as fueling rate, boost pressure, and speed on both the CNL and RI are studied. Results show that the CNL is not significantly affected by the high-frequency components related to the ringing/knock phenomenon.

This study explores the use of two conventional ignition improvers, 2-ethylhexyl nitrate (EHN) and di-tert-butyl peroxide (DTBP), to enhance the autoignition of the regular gasoline in an homogeneous charge compression ignition (HCCI) engine at naturally aspirated and moderately boosted conditions (up to 180 kPa absolute) with a constant engine speed of 1200 rpm. The results showed that both EHN and DTBP are very effective for reducing the intake temperature (Tin) required for autoignition and for enhancing stability to allow a higher charge-mass fuel/air equivalence ratio (ϕm). On the other hand, the addition of these additives can also make the gasoline too reactive at some conditions, so significant exhaust gas recirculation (EGR) is required at these conditions to maintain the desired combustion phasing. Thus, there is a trade-off between improving stability and reducing the oxygen available for combustion when using ignition improvers to extend the high-load limit.

A detailed understanding of the various factors affecting the trends in gross-indicated thermal efficiency with changes in key operating parameters has been carried out, applied to a one-liter displacement single-cylinder boosted Low-Temperature Gasoline Combustion (LTGC) engine. This work systematically investigates how the supplied fuel energy splits into the following four energy pathways: gross-indicated thermal efficiency, combustion inefficiency, heat transfer and exhaust losses, and how this split changes with operating conditions. Additional analysis is performed to determine the influence of variations in the ratio of specific heat capacities (γ) and the effective expansion ratio, related to the combustion-phasing retard (CA50), on the energy split. Heat transfer and exhaust losses are computed using multiple standard cycle analysis techniques. The various methods are evaluated in order to validate the trends.

Low-temperature gasoline combustion (LTGC), based on the compression ignition of a premixed or partially premixed dilute charge, can provide thermal efficiencies (TE) and maximum loads comparable to those of turbo-charged diesel engines, and ultra-low NOx and particulate emissions. Intake boosting is key to achieving high loads with dilute combustion, and it also enhances the fuel's autoignition reactivity, reducing the required intake heating or hot residuals. These effects have the advantages of increasing TE and charge density, allowing greater timing retard with good stability, and making the fuel ϕ- sensitive so that partial fuel stratification (PFS) can be applied for higher loads and further TE improvements. However, at high boost the autoignition reactivity enhancement can become excessive, and substantial amounts of EGR are required to prevent overly advanced combustion.

Engine acoustics measured by microphones near the engine have been used in controlled laboratory settings for combustion feedback and even combustion phasing control, but the use of these techniques in a vehicle where many other noise sources exist is problematic. In this study, surface-mounted acoustic emissions sensors are embedded in the block of a 2.0L turbocharged GDI engine, and the signal is analyzed to identify useful feedback features. The use of acoustic emissions sensors, which have a very high frequency response and are commonly used for detecting material failures for health monitoring, including detecting gear pitting and ring scuffing on test stands, enables detection of acoustics both within the range of human hearing and in the ultrasonic spectrum. The high-speed acoustic time-domain data are synchronized with the crank-angle-domain combustion data to investigate the acoustic emissions response caused by various engine events.

Low-temperature gasoline combustion (LTGC) has the potential to provide gasoline-fueled engines with efficiencies at or above those of diesel engines and extremely low NOx and particulate emissions. Three key performance goals for LTGC are to obtain high loads, reduce the boost levels required for these loads, and achieve high thermal efficiencies (TEs). This paper reports the results of an experimental investigation into the use of partial fuel stratification, produced using early direct fuel injection (Early-DI PFS), and an increased compression ratio (CR) to achieve significant improvements in these performance characteristics. The experiments were conducted in a 0.98-liter single-cylinder research engine. Increasing the CR from 14:1 to 16:1 produced a nominal increase in the TE of about one TE percentage unit for both premixed and Early-DI PFS operation.

This simulation study explores the potential synergy between the HCCI engine system and three hybrid electric vehicle (HEV) configurations, and proposes the supervisory control strategy that maximizes the benefits of combining these two technologies. HCCI operation significantly improves fuel efficiency at part load, while hybridization aims to reduce low load/low speed operation. Therefore, a key question arises: are the effects of these two technologies additive or overlapping? The HEV configurations include two parallel hybrids with varying degrees of electrification, e.g. with a 5kW integrated starter/motor (“Mild”) and with a 10 kW electric machine (“Medium”), and a power-split hybrid. The engine is a dual-mode, SI-HCCI system and the engine map reflects the impact of HCCI on brake specific fuel consumption.

This article investigates the effects of various primary reference fuel (PRF) blends, compression ratios, and intake temperatures on the thermodynamics and performance of homogeneous charge compression ignition (HCCI) combustion in a Cooperative Fuels Research (CFR) engine. Combustion phasing was kept constant at a CA50 phasing of 5° after top dead center (aTDC) and the equivalence ratio was kept constant at 0.3. Meanwhile, the compression ratio varied from 8:1 to 15:1 as the PRF blends ranged from pure n-heptane to nearly pure isooctane. The intake temperature was used to match CA50 phasing. In addition to the experimental results, a GT-Power model was constructed to simulate the experimental engine and the model was validated against the experimental data. The GT-Power model and simulation results were used to help analyze the energy flows and thermodynamic conditions tested in the experiment.

In this work, a novel opposed piston architecture is proposed where one crankshaft rotates at twice the speed of the other. This results in one piston creating a 2-stroke profile and another with a 4-stroke profile. In this configuration, the slower piston operates in the 2-stroke CAD domain, while the faster piston completes 2 reciprocating cycles in the same amount of time (4-stroke). The key benefit of this cycle is that the 4-stroke piston increases the rate of compression and expansion (dV/dθ), which lowers the combustion-induced pressure rise rate after top dead center (crank angle location of minimum volume). Additionally, it lowers in-cylinder temperatures and pressures more rapidly, resulting in a lower residence time at high temperatures, which reduces residence time for thermal NOx formation and reduces the temperature differential between the gas and the wall, thereby reducing heat transfer.

In this work, two blends of isopropanol, n-butanol, and ethanol (IBE) that can be produced by metabolically engineered clostridium acetobutylicum are studied experimentally in advanced compression ignition (ACI). This is done to determine whether these fuel blends have the right fuel properties to enable thermally stratified compression ignition, a stratified ACI strategy that using the cooling potential of single stage ignition fuels to control the heat release process. The first microorganism, ATCC824, produces a blend of 34.5% isopropanol, 60.1% n-butanol, and 5.4% ethanol, by mass. The second microorganism, BKM19, produces a blend of 12.3% isopropanol, 54.0% n-butanol, and 33.7% ethanol, by mass. The sensitivity of both IBE blends to intake pressure, intake temperature, and cylinder energy content (fueling rate) is characterized and compared to that of its neat constituents. Both IBE blends behaved similarly with a reactivity level between that of ethanol and n-butanol.

Computational Fluid Dynamics (CFD) modeling was used to investigate the effects of the direct injection of wet ethanol at various injection timings during the intake stroke in a diesel engine with a shallow bowl piston. Thermally Stratified Compression Ignition (TSCI) has been proposed to expand the operating range of Low Temperature Combustion (LTC) by broadening the temperature distribution in the cylinder prior to ignition. TSCI is accomplished by injecting either water or a water-fuel mixture with a high latent heat of vaporization like wet ethanol. This current study focuses on isolating the effects that injecting such a high heat of vaporization mixture during the intake stroke has on the distribution of temperature and equivalence ratio in the cylinder before the onset of combustion. A CONVERGE 3-D CFD model of a single cylinder diesel research engine using Reynolds Averaged Naiver Stokes (RANS) turbulence modeling was developed and validated against experimental data.

The current test methods are insufficient to evaluate and ensure the safety and reliability of vehicle system for all possible dynamic situations including the worst cases such as rollover, spin-out and so on. Although the known NHTSA J-turn and Fish-hook steering maneuvers are applied for the vehicle performance assessment, they are not enough to predict other possible worst case scenarios. Therefore, it is crucial to search for the various worst cases including the existing severe steering maneuvers. This paper includes the procedure to search for other useful worst case based upon the existing worst case scenarios in terms of rollover and its application in simulation basis. The human steering angle is selected as a design variable and optimized to maximize the index function to be expressed in terms of vehicle roll angle. The obtained scenarios were enough to generate the worse cases than NHTSA ones.

In this paper, a simulation-based dynamic rollover evaluation procedure is described. This work is based on the worst-case methodology developed at the University of Michigan, and is the result of a collaborated research project between the University of Michigan and TRW Inc. The target vehicle studied in this paper is a large production volume SUV. This vehicle is equipped with a production-intent TRW Vehicle Stability Control (VSC) system. The main goals of this paper are to (i) study the rollover propensity of this SUV, as influenced by vehicle and environment parameters such as vehicle speed, road condition, etc.; and (ii) investigate whether, and by how much, does the VSC system influence the rollover propensity of this SUV. The modeling, evaluation procedure, and preliminary evaluation results are reported.

A hybrid electric vehicle simulation tool (HE-VESIM) has been developed at the Automotive Research Center of the University of Michigan to study the fuel economy potential of hybrid military/civilian trucks. In this paper, the fundamental architecture of the feed-forward parallel hybrid-electric vehicle system is described, together with dynamic equations and basic features of sub-system modules. Two vehicle-level power management control algorithms are assessed, a rule-based algorithm, which mainly explores engine efficiency in an intuitive manner, and a dynamic-programming optimization algorithm. Simulation results over the urban driving cycle demonstrate the potential of the selected hybrid system to significantly improve vehicle fuel economy, the improvement being greater when the dynamic-programming power management algorithm is applied.

This paper investigates the opportunities for improving truck fuel economy through the use of a Fuel Cell Auxiliary Power Unit (FC APU) for silent watch, as well as for powering electrified engine accessories during driving. The particular vehicle selected as the platform for this study is a prototype of the Family of Medium Tactical Vehicles (FMTV) capable of carrying a 5 ton payload. Peak stand-by power requirements for on-board power are determined from the projected future digitized battlefield vehicle requirements. Strategic selection of electrified engine accessories enables engine shutdowns when the vehicle is stopped, thus providing additional fuel savings. Proton Exchange Membrane (PEM) fuel cell is integrated with a partial oxidation reformer in order to allow the use of the same fuel (JP8) as for the propulsion diesel engine.

For lean or dilute, boosted gasoline compression-ignition engines operating in a low-temperature combustion mode, creating a partially stratified fuel charge mixture prior to auto-ignition can be beneficial for reducing the heat-release rate (HRR) and the corresponding maximum rate of pressure rise. As a result, partial fuel stratification (PFS) can be used to increase load and/or efficiency without knock (i.e. without excessive ringing). In this work, a double direct-injection (D-DI) strategy is investigated for which the majority of the fuel is injected early in the intake stroke to create a relatively well-mixed background mixture, and the remaining fuel is injected in the latter part of the compression stroke to produce greater fuel stratification prior auto-ignition. Experiments were performed in a 1-liter single-cylinder engine modified for low-temperature gasoline combustion (LTGC) research.

The operating range of Homogeneous Charge Compression Ignition (HCCI) engines is limited to low and medium loads by high heat release rates. Negative Valve Overlap (NVO) can be used to facilitate ignition of high octane number fuels and control pressure rise rates by diluting the mixture with hot residual gas and introducing some thermal stratification. Controlling the thermal stratification results in sequential autoignition, reduced heat release rates, and operating range extension. Therefore, fundamental understanding of thermal stratification in HCCI combustion with high levels of internal residuals is necessary, along with the development of appropriate models to simulate thermal stratification and its effects on HCCI combustion. A 3-D Computational Fluid Dynamics (CFD) model of a 2.0 L GM Ecotec engine (LNF type) engine cylinder, modified for HCCI combustion, was developed using CONVERGE CFD.

Opposed-piston two-stroke (OP-2S) engines have the potential to achieve higher thermal efficiency than a conventional four-stroke diesel engine. However, the uniflow scavenging process is difficult to control over a wider range of speed and loads due to its sensitivity to pressure dynamics, port timings, and port design. Specifically, the angle of the intake ports can be used to generate swirl which has implications for open and closed cycle effects. This study proposes an analysis of the effects of port angle on the in-cylinder flow distribution and combustion performance of an OP-2S using computational fluid dynamics engine. Large Eddy Simulation (LES) was used to model turbulence given its ability to predict in-cylinder mixing and cyclic variability. A three-cylinder model was validated to experimental data collected by Achates Power and the grid was verified using an LES quality approach from the literature.

A CFD investigation has been conducted to study the efficiency and emissions characteristics of Thermally Stratified Compression Ignition (TSCI) combustion with direct water injection. The motivation for using this new low temperature combustion mode is its ability to control the heat release process by introducing a forced and controlled thermal stratification beyond what would occur naturally. In this case, TSCI is enabled using direct water injection. The added degree of control over the combustion process allows for a significantly broader operable load range compared to HCCI. The effects of injection parameters including the pressure, start of injection (SOI) timing, and spray pattern have been shown previously to affect the heat release of TSCI and its induced thermal stratification. In the present work, the efficiency and emissions considerations were investigated in detail, and the effects of injected mass are presented.

This paper describes a test cell setup for concurrent running of a real engine and a vehicle system simulation, and its use for evaluating engine performance when integrated with a conventional and a hybrid electric driveline/vehicle. This engine-in-the-loop (EIL) system uses fast instruments and emission analyzers to investigate how critical in-vehicle transients affect engine system response and transient emissions. Main enablers of the work include the highly dynamic AC electric dynamometer with the accompanying computerized control system and the computationally efficient simulation of the driveline/vehicle system. The latter is developed through systematic energy-based proper modeling that tailors the virtual model to capture critical powertrain transients while running in real time. Coupling the real engine with the virtual driveline/vehicle offers a chance to easily modify vehicle parameters, and even study two different powertrain configurations.