Search Results

Standard

Materials for Plastic Check Valves for Vacuum Booster Systems

2001-05-14

CURRENT

J1875_200105

The materials defined by this SAE Standard are unreinforced thermoplastic acetal and thermoplastic 6/6 heat stabilized nylon, as both materials will function in this application. The specific material chosen will depend on the final application's surroundings and heat requirements. They are for use in vacuum booster check valves for hydraulic brake systems.

Standard

Brake Hydraulic Component Low Pressure Flow Rate Measurement

2015-08-11

CURRENT

J2994_201508

The SAE Recommended Practice specifies a standardize method and test procedure to measure low pressure differential (< 1bar) brake component brake fluid flow performance. The standard can be utilized for flow measurements across hydraulic brake components such as master cylinders, apply system to chassis controls piping, or other sources of flow restriction in the low pressure side of the hydraulic brake system. It covers materials, manufacturing processes, and general properties required to meet the wide range of service encountered in automotive application. This specification covers only low pressure differential fluid flow and does not include measurement recommended practice for High Pressure differential (> 1 bar) flows.

Standard

REMANUFACTURED HYDRAULIC MASTER CYLINDER FOR MOTOR VEHICLE BRAKES—GENERAL CHARACTERISTICS AND TEST PROCEDURE

1994-06-01

HISTORICAL

J1693_199406

This SAE Recommended Practice specifies the general characteristics and test procedure to define the minimum characteristics, performance, and durability requirements. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The minimum characteristics, performance, and durability requirements are specified in SAE J1694.

Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - General Characteristics and Test Procedure

2012-04-30

CURRENT

J1693_201204

This SAE Recommended Practice specifies the general characteristics and test procedure to define the minimum characteristics, performance, and durability requirements. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The minimum characteristics, performance, and durability requirements are specified in SAE J1694.

Standard

REMANUFACTURED HYDRAULIC MASTER CYLINDER FOR MOTOR VEHICLE BRAKES—PERFORMANCE REQUIREMENTS

1994-06-26

HISTORICAL

J1694_199406

This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.

Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - Performance Requirements

2012-04-30

CURRENT

J1694_201204

This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.

Standard

Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders

2001-05-14

HISTORICAL

J1568_200105

The materials defined by this SAE Standard are glass-fiber-reinforced, mineral-filled phenolic molding compounds suitable for compression molding. Preforms may be radio frequency preheated or screw preheated slugs. Compound for use in hydraulic disc brake caliper pistons.

Standard

Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders

2012-04-30

CURRENT

J1568_201204

The materials defined by this SAE Standard are glass-fiber-reinforced, mineral-filled phenolic molding compounds suitable for compression molding. Preforms may be radio frequency preheated or screw preheated slugs. Compound for use in hydraulic disc brake caliper pistons.

Standard

Hydraulic Power Assist Brake Booster Test Procedure

2012-02-17

CURRENT

J1807_201202

This SAE Standard applies to direct acting hydraulic power assist brake boosters only, of the type which provide "push through" manual braking of the static brake circuit(s) via a separate master cylinder, in event of inoperative power assistance similar to existing vacuum boosters (SAE J1808), for passenger cars and light trucks [4500 kg GVW (10 000 lb)].

Standard

Hydraulic Power Assist Brake Booster Test Procedure

2000-11-03

HISTORICAL

J1807_200011

This SAE Standard applies to direct acting hydraulic power assist brake boosters only, of the type which provide “push through” manual braking of the static brake circuit(s) via a separate master cylinder, in event of inoperative power assistance similar to existing vacuum boosters (SAE J1808), for passenger cars and light trucks [4500 kg GVW (10 000 lb)].

Standard

Shelf Storage of Hydraulic Brake Components

1998-01-01

HISTORICAL

J1825_199801

This SAE Information Report is the listing of recommendations for shelf storage for hydraulic brake components. Included in brake components are wheel cylinders, master cylinders, combination valves, and disc brake caliper assemblies. This document is not a specification. This document embodies the analyses and experiences of many users and manufacturers. Where specific manufacturers' recommendations are made, those recommendations shall supersede the recommendations of this document. This document lists the successful procedures and practices associated with brake components based on long experience of a wide cross section of manufacturers and users. The practices are expected to be applied to all brake components where SAE standards are applicable.

Standard

Shelf Storage of Hydraulic Brake Components

2005-01-05

HISTORICAL

J1825_200501

This SAE Information Report is the listing of recommendations for shelf storage for hydraulic brake components. Included in brake components are wheel cylinders, master cylinders, combination valves, and disc brake caliper assemblies. This document is not a specification. This document embodies the analyses and experiences of many users and manufacturers. Where specific manufacturers' recommendations are made, those recommendations shall supersede the recommendations of this document. This document lists the successful procedures and practices associated with brake components based on long experience of a wide cross section of manufacturers and users. The practices are expected to be applied to all brake components where SAE standards are applicable.

Standard

Shelf Storage of Hydraulic Brake Components

2012-04-30

CURRENT

J1825_201204

This SAE Information Report is the listing of recommendations for shelf storage for hydraulic brake components. Included in brake components are wheel cylinders, master cylinders, combination valves, and disc brake caliper assemblies. This document is not a specification. This document embodies the analyses and experiences of many users and manufacturers. Where specific manufacturers' recommendations are made, those recommendations shall supersede the recommendations of this document. This document lists the successful procedures and practices associated with brake components based on long experience of a wide cross section of manufacturers and users. The practices are expected to be applied to all brake components where SAE standards are applicable.

Standard

Rubber Cups for Hydraulic Actuating Cylinders

2011-03-16

CURRENT

J1601_201103

These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document.

Standard

RUBBER CUPS FOR HYDRAULIC ACTUATING CYLINDERS

1997-07-01

HISTORICAL

J1601_199707

These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document.

Standard

RUBBER CUPS FOR HYDRAULIC ACTUATING CYLINDERS

1990-11-26

HISTORICAL

J1601_199011

These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document.

Standard

Rubber Cups for Hydraulic Actuating Cylinders

1975-05-01

HISTORICAL

J1601_197505

These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber comound. Disc brake seals are not covered by this document.

Standard

AUTOMOTIVE HYDRAULIC BRAKE SYSTEM—METRIC BANJO BOLT CONNECTIONS

1989-05-01

HISTORICAL

J1291_198905

This standard documents dimensional metric specifications for hydraulic brake system threaded ports and banjo bolts for the interconnection of major components in automotive hydraulic brake systems. Banjo blocks are not covered by this standard. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices). Some applications may require sizes or forms other than those shown herein, and this document does not preclude such other details when they are required.

Standard

Brake Master Cylinder Reservoir Diaphragm Gasket

2014-11-26

CURRENT

J1605_201411

This SAE Standard covers performance requirements and methods of test for master cylinder reservoir diaphragm gaskets that will provide a functional seal and protection from outside dirt and water.

Standard

BRAKE MASTER CYLINDER RESERVOIR DIAPHRAGM GASKET

1992-03-20

HISTORICAL

J1605_199203

This SAE Standard covers performance requirements and methods of test for master cylinder reservoir diaphragm gaskets that will provide a functional seal and protection from outside dirt and water.