Search Results

The scope of this new recommended practice should include, but not necessarily be limited to: 1. Define vehicle operating conditions used to drive MOC-EPB actuator design and selection 2. Define brake corner operating conditions (e.g. temperature and state of burnish) used to drive MOC-EPB actuator design and selection 3. Define actuator operating conditions (e.g. temperature, voltage, current limit, and state of wear) used to drive MOC-EPB actuator design and selection 4. Define methodology for addressing part to part variation in performance

This recommended practice provides a method, test set-up, and test conditions for brake hydraulic component flow rate measurement for high differential pressure (>5 bar) flow conditions. It is intended for hydraulic brake components which affect the brake fluid flow characteristics in a hydraulic brake circuit, that are part of a circuit for which the flow characteristics are important to system operation, and that are exposed to high operating pressure differentials (in the 5 to 100 bar range). Typical applications may include measurement of flow through chassis controls valve bodies, orifices in the brake system such as in flow bolts, junction blocks, and master cylinders, and through brake pipe configurations.

This SAE Recommended Practice specifies the general characteristics and test procedure to define the minimum characteristics, performance, and durability requirements. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The minimum characteristics, performance, and durability requirements are specified in SAE J1694.

This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.

This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.

This SAE Standard applies to direct acting hydraulic power assist brake boosters only, of the type which provide "push through" manual braking of the static brake circuit(s) via a separate master cylinder, in event of inoperative power assistance similar to existing vacuum boosters (SAE J1808), for passenger cars and light trucks [4500 kg GVW (10 000 lb)].

This SAE Standard applies to direct acting hydraulic power assist brake boosters only, of the type which provide “push through” manual braking of the static brake circuit(s) via a separate master cylinder, in event of inoperative power assistance similar to existing vacuum boosters (SAE J1808), for passenger cars and light trucks [4500 kg GVW (10 000 lb)].

This SAE Information Report is the listing of recommendations for shelf storage for hydraulic brake components. Included in brake components are wheel cylinders, master cylinders, combination valves, and disc brake caliper assemblies. This document is not a specification. This document embodies the analyses and experiences of many users and manufacturers. Where specific manufacturers' recommendations are made, those recommendations shall supersede the recommendations of this document. This document lists the successful procedures and practices associated with brake components based on long experience of a wide cross section of manufacturers and users. The practices are expected to be applied to all brake components where SAE standards are applicable.

This SAE Recommended Practice specifies the performance test procedures and requirements of a plastic reservoir assembly suitable for use on a hydraulic brake master cylinder (reference SAE J1153). Intended usage is for on-road vehicles using brake fluid conforming to fMVSS-116 (DOT 3), and SAE J1703 specifications. This document includes the cap.cover and diaphragm as integral parts of the reservoir assembly. The fluid level sensor (FLS) is also included as an integral part of the assembly. However, additional FLS standards and/or requirements are applicable and necessary which are not covered in this document. This document is intended to provide a recommended practice and minimum performance requirements of current established designs on those reservoir assemblies generally used by individual manufacturers which have demonstrated satisfactory field performance. This document is applicable to new reservoir assemblies for commercial or aftermarket production.

This document applies to direct acting vacuum power assist brake boosters only, exclusive of the master cylinder or other brake system prime mover devices for passenger cars and light trucks [4500 kg GVW (10 000 lb)]. It specifies the test procedure to determine minimum performance and durability characteristics.

This document applies to direct acting vacuum power assist brake boosters only, exclusive of the master cylinder or other brake system prime mover devices for passenger cars and light trucks [4500 kg GVW (10 000 lb)]. It specifies the test procedure to determine minimum performance and durability characteristics which are specified in SAE J1902 (under development).

This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to +120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).

This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of −40 to +120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).

This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).

The recommended practice specifies the test procedure to determine minimum performance and durability characteristics for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild). The minimum performance and durability requirements are specified in SAE J1154, Hydraulic Master Cylinders for Motor Vehicle Brakes—Performance Requirements.

This SAE Standard specifies the test procedure to determine minimum performance and durability characteristics for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild). The minimum performance and durability requirements are specified in SAE J1154.

This SAE Standard specifies the test procedure to determine minimum performance and durability characteristics for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild). The minimum performance and durability requirements are specified in SAE J1154.

The Recommended Practice specifies the test procedure to assure valve assemblies which are satisfactory for vehicle usage, and it is applicable to new valve assemblies from commercial production, and remanfacture (factory rebuild). The minimum performance and durability requirements are specified in SAE J1137, Hydraulic Valves for Motor Vehicle Brake Systems-Performance Requirements.

This SAE Recommended Practice applies to valve assemblies that are used on passenger car and light truck braking systems utilizing motor vehicle hydraulic brake fluids. The procedure (SAE J1118) and these requirements (SAE J1137) were developed for brake fluids conforming to SAE J1703 and FMVSS 116 (DOT 3) requirements; however, it may be utilized for valves which use DOT 4 or DOT 5 brake fluid. These requirements are applicable to differential warning, metering hold off, bypass function, or proportioning type valves or any combination thereof.

This SAE Recommended Practice applies to valve assemblies that are used on passenger car and light truck braking systems utilizing motor vehicle hydraulic brake fluids. The procedure (SAE J1118) and these requirements (SAE J1137) were developed for brake fluids conforming to SAE J1703 and FMVSS 116 (DOT 3) requirements; however, it may be utilized for valves which use DOT 4 or DOT 5 brake fluid. These requirements are applicable to differential warning, metering hold off, bypass function, or proportioning type valves or any combination thereof.