Search Results

Standard

Materials for Plastic Check Valves for Vacuum Booster Systems

2001-05-14

CURRENT

J1875_200105

The materials defined by this SAE Standard are unreinforced thermoplastic acetal and thermoplastic 6/6 heat stabilized nylon, as both materials will function in this application. The specific material chosen will depend on the final application's surroundings and heat requirements. They are for use in vacuum booster check valves for hydraulic brake systems.

Standard

REMANUFACTURED HYDRAULIC MASTER CYLINDER FOR MOTOR VEHICLE BRAKES—GENERAL CHARACTERISTICS AND TEST PROCEDURE

1994-06-01

HISTORICAL

J1693_199406

This SAE Recommended Practice specifies the general characteristics and test procedure to define the minimum characteristics, performance, and durability requirements. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The minimum characteristics, performance, and durability requirements are specified in SAE J1694.

Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - General Characteristics and Test Procedure

2012-04-30

CURRENT

J1693_201204

This SAE Recommended Practice specifies the general characteristics and test procedure to define the minimum characteristics, performance, and durability requirements. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The minimum characteristics, performance, and durability requirements are specified in SAE J1694.

Standard

REMANUFACTURED HYDRAULIC MASTER CYLINDER FOR MOTOR VEHICLE BRAKES—PERFORMANCE REQUIREMENTS

1994-06-26

HISTORICAL

J1694_199406

This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.

Standard

Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - Performance Requirements

2012-04-30

CURRENT

J1694_201204

This SAE Recommended Practice defines minimum requirements for general characteristics, performance, and durability. It is applicable to remanufactured assemblies (factory rebuild) only. This document applies to master cylinder assemblies and components of current established designs but does not cover fluid level sensors, integral proportioning valves, or those master cylinders used in anti-lock brake or traction control systems. These will be covered by other standards. The general characteristics and test procedure are specified in SAE J1693.

Standard

Hydraulic Power Assist Brake Booster Test Procedure

2012-02-17

CURRENT

J1807_201202

This SAE Standard applies to direct acting hydraulic power assist brake boosters only, of the type which provide "push through" manual braking of the static brake circuit(s) via a separate master cylinder, in event of inoperative power assistance similar to existing vacuum boosters (SAE J1808), for passenger cars and light trucks [4500 kg GVW (10 000 lb)].

Standard

Hydraulic Power Assist Brake Booster Test Procedure

2000-11-03

HISTORICAL

J1807_200011

This SAE Standard applies to direct acting hydraulic power assist brake boosters only, of the type which provide “push through” manual braking of the static brake circuit(s) via a separate master cylinder, in event of inoperative power assistance similar to existing vacuum boosters (SAE J1808), for passenger cars and light trucks [4500 kg GVW (10 000 lb)].

Standard

Plastic Dust Shield for Hydraulic Disc Brakes

2012-03-20

CURRENT

J1876_201203

The material defined by this SAE document is an impact modified, heat stabilized, 66 nylon reinforced with glass fibers. This material is for use in dust shields for hydraulic disc brakes. NOTE—The applicability of a plastic dust shield must be evaluated for each individual brake system. Its use with solid rotors and/or high performance brake systems is not recommended.

Standard

Plastic Dust Shield for Hydraulic Disc Brakes

2001-05-14

HISTORICAL

J1876_200105

The material defined by this SAE document is an impact modified, heat stabilized, 66 nylon reinforced with glass fibers. This material is for use in dust shields for hydraulic disc brakes.

Standard

Vacuum Power Assist Brake Booster Test Procedure

2015-06-30

CURRENT

J1808_201506

This document applies to direct acting vacuum power assist brake boosters only, exclusive of the master cylinder or other brake system prime mover devices for passenger cars and light trucks [4500 kg GVW (10 000 lb)]. It specifies the test procedure to determine minimum performance and durability characteristics.

Standard

VACUUM POWER ASSIST BRAKE BOOSTER TEST PROCEDURE

1989-10-01

HISTORICAL

J1808_198910

This document applies to direct acting vacuum power assist brake boosters only, exclusive of the master cylinder or other brake system prime mover devices for passenger cars and light trucks [4500 kg GVW (10 000 lb)]. It specifies the test procedure to determine minimum performance and durability characteristics which are specified in SAE J1902 (under development).

Standard

Rubber Seals for Hydraulic Disc Brake Cylinders

2008-05-13

HISTORICAL

J1603_200805

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.

Standard

Rubber Seals for Hydraulic Disc Brake Cylinders

2014-12-03

CURRENT

J1603_201412

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.

Standard

RUBBER SEALS FOR HYDRAULIC DISC BRAKE CYLINDERS

1990-06-01

HISTORICAL

J1603_199006

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.

Standard

Structural Testing of Passenger Car and Truck Disc Brakes

1998-01-01

HISTORICAL

J1713_199801

This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.

Standard

Structural Testing of Passenger Car and Truck Disc Brakes

2004-06-07

HISTORICAL

J1713_200406

This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.

Standard

Structural Testing of Passenger Car and Truck Disc Brakes

2013-02-13

HISTORICAL

J1713_201302

This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.

Standard

Structural Testing of Passenger Car and Truck Disc Brakes

2014-11-15

CURRENT

J1713_201411

This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.

Standard

Hydraulic Wheel Cylinders for Automotive Drum Brakes

2013-07-09

CURRENT

J101_201307

This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).

Standard

HYDRAULIC MASTER CYLINDERS FOR MOTOR VEHICLE BRAKES TEST PROCEDURE

1991-06-01

HISTORICAL

J1153_199106

This SAE Standard specifies the test procedure to determine minimum performance and durability characteristics for master cylinder assemblies of current established designs, components of which conform to SAE Standards. It is applicable to new assemblies from commercial production and remanufacture (factory rebuild). The minimum performance and durability requirements are specified in SAE J1154.