Refine Your Search

Search Results

Standard

Connections for Fluid Power and General Use-Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing Part 1: Port With O-Ring Seal in Truncated Housing

1991-12-01
HISTORICAL
J2244/1_199112
This part of SAE J2244 specifies dimensions for fluid power metric ports for use with adjustable and nonadjustable stud ends shown in SAE J2244/2. Ports in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications.
Standard

Connections for Fluid Power and General Use—Ports and Stud Ends with ISO 261 Threads and O-Ring Sealing Part 1: Port with O-Ring Seal in Truncated Housing

2007-12-21
CURRENT
J2244/1_200712
This part of SAE J2244 specifies dimensions for fluid power metric ports for use with adjustable and nonadjustable stud ends shown in SAE J2244/2. Ports in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Metric Threads and O-Ring Sealing, Part 3: Light-Duty (L Series) Stud Ends--Dimensions, Design, Test Methods, and Requirements

2007-12-21
CURRENT
J2244/3_200712
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable light-duty (L series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 40 MPa for nonadjustable stud ends and 31.5 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydraulic fluid power applications. Conformance to the dimensional information in this SAE Standard does not guarantee rated performance.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing Part 3: Light-Duty (L Series) Stud End--Dimensions, Design, Test Methods, and Requirements

1996-04-01
HISTORICAL
J2244/3_199604
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable light-duty (L series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 40 MPa for nonadjustable stud ends and 31.5 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydraulic fluid power applications. Conformance to the dimensional information in this SAE Standard does not guarantee rated performance.
Standard

Connections for Fluid Power and General Use Ports and Stud Ends with ISO 261 Metric Threads and O-Ring Sealing, Part 3: Light-Duty (L Series) Stud Ends Dimensions, Design, Test Methods, and Requirements

1998-06-01
HISTORICAL
J2244/3_199806
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable light-duty (L series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 40 MPa for nonadjustable stud ends and 31.5 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydraulic fluid power applications. Conformance to the dimensional information in this SAE Standard does not guarantee rated performance.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing--Part 4: Heavy-Duty (S Series) External Hex Port Plugs--Dimensions, Design, Test Methods, and Requirements

1997-01-01
HISTORICAL
J2244/4_199701
This part of SAE J2244 specifices dimensions, performance requirements, and test procedures for metric external hex O-rings port plugs. Port plugs in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydrualic fluid power applications. Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance ratings.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Threads and O-Ring Sealing--Part 4: Heavy-Duty (S Series) External Hex Port Plugs--Dimensions, Design, Test Methods, and Requirements

2007-12-21
CURRENT
J2244/4_200712
This part of SAE J2244 specifices dimensions, performance requirements, and test procedures for metric external hex O-rings port plugs. Port plugs in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydrualic fluid power applications. Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance ratings.
Standard

Connections for Fluid Power and High Pressure Use - Ports, Stud Ends, and Plugs With Iso 261 Threads and O-Rings Sealing - Part 2: Stud End Requirements, Dimensions, Design and Test Methods

2002-10-04
HISTORICAL
J2337/2_200210
Purpose This part of SAE J2337 specifies dimensions, design, and performance requirements for eight connectors using a conical seal to insure leak proof performance with a design factor of 4 to 1. Field of Application These connectors are intended for general and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These connectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuum to the working pressures shown in Table 1. Since many factors influence the pressure at which hydraulic systems will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that the required performance levels are met.
Standard

Connections for Fluid Power and High Pressure Use--Ports, Stud Ends, and Plugs with ISO 261 Threads and O-Ring Sealing--Part 1: Ports with Recessed Conical Seat Requirements, Dimensions, Design, and Test Methods

2009-08-12
HISTORICAL
J2337/1_200908
Purpose This part of SAE J2337 specifies dimensions, design, and performance requirements for eight ports using a conical seal to insure leak proof performance with a design factor of 4 to 1. Field of Application These connectors are intended for general and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These connectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuum to the working pressures shown in Table 1. Since many factors influence the pressure at which hydraulic systems will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that the required performance levels are met.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Threads and O-Ring Sealing Part 2: Heavy-Duty (S Series) Stud Ends--Dimensions, Design, Test Methods, and Requirements

2007-12-21
CURRENT
J2244/2_200712
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable heavy-duty (S Series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications. Conformance to the dimensional information in this standard does not guarantee rated performance.
Standard

Connections for Fluid Power and General Use-Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing Part 2: Heavy-Duty (S Series) Stud Ends- Dimensions, Design, Test Methods, and Requirements

1991-12-01
HISTORICAL
J2244/2_199112
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable heavy-duty (S Series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications. Conformance to the dimensional information in this standard does not guarantee rated performance.
Standard

Fitting--O-Ring Face Seal

1996-06-01
HISTORICAL
J1453_199606
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1993-06-01
HISTORICAL
J1453_199306
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Fitting--O-Ring Face Seal

1994-06-01
HISTORICAL
J1453_199406
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
X