Search Results

A prior study (Chon and Heywood, [1]) examined how the design and performance of spark-ignition engines evolved in the United States during the 1980s and 1990s. This paper carries out a similar analysis of trends in basic engine design and performance characteristics over the past decade. Available databases on engine specifications in the U.S., Europe, and Japan were used as the sources of information. Parameters analyzed were maximum torque, power, and speed; number of cylinders and engine configuration, cylinder displacement, bore, stroke, compression ratio; valvetrain configuration, number of valves and their control; port or direct fuel injection; naturally-aspirated or turbocharged engine concepts; spark-ignition and diesel engines. Design features are correlated with these engine’s performance parameters, normalized by engine and cylinder displacement.

An experimental study was performed to develop a more fundamental understanding of the effects of secondary air injection (SAI) on exhaust gas emissions and catalyst light-off characteristics during cold start of a modern SI engine. The effects of engine operating parameters and various secondary air injection strategies such as spark retardation, fuel enrichment, secondary air injection location and air flow rate were investigated to understand the mixing, heat loss, and thermal and catalytic oxidation processes associated with SAI. Time-resolved HC, CO and CO₂ concentrations were tracked from the cylinder exit to the catalytic converter outlet and converted to time-resolved mass emissions by applying an instantaneous exhaust mass flow rate model. A phenomenological model of exhaust heat transfer combined with the gas composition analysis was also developed to define the thermal and chemical energy state of the exhaust gas with SAI.

The rotary engine provides high power density compared to piston engine, but one of its downside is higher oil consumption. A model of the oil seals is developed to calculate internal oil consumption (oil leakage from the crankcase through the oil seals) as a function of engine geometry and operating conditions. The deformation of the oil seals trying to conform to housing distortion is calculated to balance spring force, O-ring and groove friction, and asperity contact and hydrodynamic pressure at the interface. A control volume approach is used to track the oil over a cycle on the seals, the rotor and the housing as the seals are moving following the eccentric rotation of the rotor. The dominant cause of internal oil consumption is the non-conformability of the oil seals to the housing distortion generating net outward scraping, particularly next to the intake and exhaust port where the housing distortion valleys are deep and narrow.

The rotary engine provides high power density compared to piston engine, but one of its downside is higher oil consumption. In order to better understand oil transport, a laser induced fluorescence technique is used to visualize oil motion on the side of the rotor during engine operation. Oil transport from both metered oil and internal oil is observed. Starting from inside, oil accumulates in the rotor land during inward motion of the rotor created by its eccentric motion. Oil seals are then scraping the oil outward due to seal-housing clearance asymmetry between inward and outward motion. Cut-off seal does not provide an additional barrier to internal oil consumption. Internal oil then mixes with metered oil brought to the side of the rotor by gas leakage. Oil is finally pushed outward by centrifugal force, passes the side seals, and is thrown off in the combustion chamber.

Piston rings are large contributors to friction losses in internal combustion engines. To achieve higher engine efficiency, low friction ring packs that can maintain good sealing performance must be designed. To support this effort, simulation tools have been developed to model the performance of piston rings during engine operation. However, the challenge of predicting oil consumption, blow by, and ring pack friction with sufficient accuracy remains. This is mostly due to the complexity of this system. Ring dynamics, deformation, interaction with liner and piston, gas and lubricant flow must all be studied together to make relevant predictions. In this paper, a new curved beam finite element model of piston rings is proposed. Ring structural deformation and contact with the liner are treated on two separate grids. A comparison with ring models in the literature and analytical solutions shows that it can provide accurate results efficiently.

As the piston pin works under significant mechanical load, it is susceptible to wear, seizure, and structural failure, especially in heavy duty internal combustion engines. It has been found that the friction loss associated with the pin is comparable to that of the piston, and can be reduced when the interface geometry is properly modified. However, the mechanism that leads to such friction reduction, as well as the approaches towards further improvement, remain unknown. This work develops a piston pin lubrication model capable of simulating the interaction between the pin, the piston, and the connecting rod. The model integrates dynamics, solid contact, oil transport, and lubrication theory, and applies an efficient numerical scheme with second order accuracy to solve the highly stiff equations. As a first approach, the current model assumes every component to be rigid.

A new ring pack model has been developed based on the curved beam finite element method. This paper describes the first part of this model: simulating gas pressure in different regions above piston skirt and ring dynamic behavior of two compression rings and a twin-land oil control ring. The model allows separate grid divisions to resolve ring structure dynamics, local force/pressure generation, and gas pressure distribution. Doing so enables the model to capture both global and local processes at their proper length scales. The effects of bore distortion, piston secondary motion, and groove distortion are considered. Gas flows, gas pressure distribution in the ring pack, and ring structural dynamics are coupled with ring-groove and ring-liner interactions, and an implicit scheme is employed to ensure numerical stability. The model is applied to a passenger car engine to demonstrate its ability to predict global and local effects on ring dynamics and oil transport.

Light-load unburned hydrocarbon emissions were studied experimentally in a spark-ignited direct-injection engine burning gasoline where the piston temperature was varied. The test engine was a single-cylinder Direct Injection Stratified-Charge (DISC) engine incorporating a combustion process similar to the Texaco Controlled Combustion System. At a single low load operating condition, the piston temperature was varied by 50 K by controlling the cooling water and oil temperature. The effect of this change on unburned hydrocarbon emissions and heat release profiles was studied. It was found that by carefully controlling the intake air temperature and pressure to maintain constant in-cylinder conditions at the time of injection, the change in piston temperature did not have a significant effect on the unburned hydrocarbon emissions from the engine.

In order to understand better the operation of spark-ignition engines during the warm-up period, a computer model had been developed which simulates the thermal processes of the engine. This model is based on lumped thermal capacitance methods for the major engine components, as well as the exhaust system. Coolant and oil flows, and their respective heat transfer rates are modeled, as well as friction heat generation relations. Piston-liner heat transfer is calculated based on a thermal resistance method, which includes the effects of piston and ring material and design, oil film thickness, and piston-liner crevice. Piston/liner crevice changes are calculated based on thermal expansion rates and are used in conjunction with a crevice-region unburned hydrocarbon model to predict the contribution to emissions from this source.

In the study of internal combustion engines, gas temperatures within the system are of significant importance. The adverse conditions under firing operation, however, make measurements by any means very difficult. This current study seems to have gone the farthest to date for velocity of sound gas temperature measurements in internal combustion engine applications. An ultrasound signal is sent by a transmitting transducer, through the gas medium, and into the receiving transducer. The received signal is recorded, and the gas temperature determined from the time of flight. In-cylinder and exhaust manifold gas temperatures under fired conditions are presented, and are all consistent. Impacts of operating parameters like mixture equivalence ratio and coolant temperature are investigated.

A dynamometer-mounted four-cylinder Saturn engine was used to accumulate combustion chamber deposits (CCD), using an additized fuel. During each deposit accumulation test, the HC emissions were continuously measured. The deposit thickness at the center of the piston was measured at the beginning of each day. After the 50 and 35-hour tests, HC emissions were measured with isooctane, benzene, toluene, and xylene, with the deposited engine, and again after the deposits had been cleaned from the engine. The HC emissions showed a rapid rise in the first 10 to 15 hours and stabilization after about 25 hours of deposit accumulation. The HC increase due to CCD accumulation accounted for 10 to 20% of the total engine-out HC emissions from the deposit build-up fuel and 10 to 30% from benzene, isooctane, toluene, and xylene, making CCDs a significant HC emissions source from this engine. The HC emissions stabilized long before the deposit thickness.

A research program designed to measure the contribution from fuel absorption in the thin layer of oil, lubricating the cylinder liner, to the total and speciated HC emissions from a spark ignition engine has been performed. The logic of the experiment design was to test the oil layer mechanism via variations in the oil layer thickness (through the lubricant formulations), solubility of the fuel components in the lubricants, and variations in the crankcase gas phase HC concentration (through crankcase purging). A set of preliminary experiments were carried out to determine the solubility and diffusivity of the fuel components in the individual lubricants. Engine tests showed similar HC emissions among the tested lubricants. No consistent increase was observed with oil viscosity (oil film thickness), contrary to what would be expected if fuel-oil absorption was contributing significantly to engine-out HC. Similarly, no effect of crankcase purging could be observed.

The single-point LIF-measurement technique has been applied to a four-cylinder spark-ignition production engine for investigation of the oil film layer between the piston, piston rings and the cylinder wall. The lubrication process was studied during engine warm-up and it was found that a scaling law could be successfully used. This scaling law enables simple scaling of the oil film thickness of the compression ring, scraper ring and on the liner during warm-up, assuming the oil film thickness and cylinder liner temperature are known for the steady-state operating condition. Thereby the value of traditional measured steady-state lubrication data is enhanced.

The effects of injection variability, low velocity fuel injection, and injector orifice size on unburned hydrocarbon emissions were studied in a direct-injection stratified-charge (DISC) engine. The engine incorporated a combustion process similar to the Texaco Controlled Combustion System (TCCS) and was operated with gasoline. The variability in the amount of fuel injected per cycle was found to have a negligible effect on HC emissions. Changing the amount of fuel injected at low velocity at the end of injection impacted the HC emissions by up to 50%. A positive pressure differential between the injection line and the combustion chamber when the injector needle closed resulted in more fuel injected at low velocity and increased HC emissions. High speed single frame photography was used to observe the end of injection. Injectors with smaller orifices had substantially lower HC emissions than the baseline injector.

Experiments were carried out to collect in-cylinder pressure data and microphone signals from a single-cylinder test engine using spark timingsbefore, at, and after knock onset for toluene reference fuels. The objective was to gain insight into the phenomena that determine knock onset, detected by an external microphone. In particular, the study examines how the end-gas autoignition process changes as the engine's spark timing is advanced through the borderline knock limit into the engine's knocking regime. Fast Fourier transforms (FFT) and bandpass filtering techniques were used to process the recorded cylinder pressure data to determine knock intensities for each cycle. Two characteristic pressure oscillation frequencies were detected: a peak just above 6 kHz and a range of peaks in the 15-22 kHz range. The microphone data shows that the audible knock signal has the same 6 kHz peak.

This paper presents a study of lubricating oil transport and exchange in a four-stroke spark ignition engine while undergoing transient load changes. The study consisted of experiments with a single cylinder test engine utilizing 2D LIF (Two Dimensional Laser Induced Fluorescence) techniques to view real time oil transport and exchange, along with computer modeling to describe certain phenomenon observed during the experiments. The computer modeling results included ring dynamics and corresponding gas flows through different regions of the power cylinder. Under steady-state conditions and constant speed during the experiments, more oil was observed on the piston at low load than at high load. Therefore, a transition from low load to high load resulted in oil leaving the piston, and a transition from high load to low load resulted in oil being added to the piston.

A dry piston secondary dynamics model has been developed. This model includes the detailed piston and cylinder bore hot shape geometries, and piston deformations due to combustion pressure, axial inertia and interaction with the cylinder bore, but neglects the effects of the hydrodynamic lubrication at the piston - cylinder bore interface in order to achieve faster calculation times. The piston - cylinder bore friction is calculated using a user supplied friction coefficient. This model provides a very useful, fast tool for power cylinder system analysis, provided its limitations are understood.

This paper discusses the influences of several cylinder liner honing surface geometrical features on the interaction between the piston twin land oil control ring (TLOCR) and the cylinder liner by using the deterministic hydrodynamic model [1] and the twin land oil control ring model [2]. Additionally, the key design parameters of the TLOCR, including ring tension and land axial width are studied. The results show significant effects of three liner honing surface features beyond height distribution, including plateau wavelength, groove density and honing angle in hydrodynamic pressure generation. The study in oil control ring design parameters reveals that both ring tension and land axial width have important influences on friction and oil consumption, and their competing effects are discussed subsequently.

Liquid fuel flow into the cylinder an important source of hydrocarbon (HC) emissions of an SI engine. This is an especially important HC source during engine warm up. This paper examines the phenomena that determine the inflow of liquid fuel through the intake valve during a simulated start-up procedure. A Phase Doppler Particle Analyzer (PDPA) was used to measure the size and velocity of liquid fuel droplets in the vicinity of the intake valve in a firing transparent flow-visualization engine. These characteristics were measured as a function of engine running time and crank angle position during four stroke cycle. Droplet characteristics were measured at 7 angular positions in 5 planes around the circumference of the intake valve for both open and closed-valve injection. Additionally the cone shaped geometry of the entering liquid fuel spray was visualized using a Planar Laser Induced Fluorescence (PLIF) setup on the same engine.

A two-dimensional Laser Induced Fluorescence (LIF) system was developed to visualize the oil distribution and study the oil transport in the piston ring pack of a single-cylinder diesel engine through an optical window on the liner. The system gives high spatial and intensity resolutions so that detailed oil distribution on the piston as well as between the rings and the liner can be studied. This work primarily focused on investigating different oil transport mechanisms on piston crown land and second land under various engine operating conditions. Oil accumulation on the crown land was observed under certain operating conditions and top ring up-scraping was deemed to be the source for this oil accumulation. Two mechanisms for the oil flow on the second land were identified, namely, inertia driven oil flow in the axial direction and oil dragging by gas flow in the circumferential direction. Finally, the effects of ring rotation were investigated.