Search Results

N-butanol and isobutanol are alcohols that can be produced from biomass by fermentation and are possibly more compatible with existing engines than ethanol. This work reports on the effects of these two isomers on exhaust emissions of an unmodified direct injection spark ignition (DISI) engine. A Ford Focus car with a 1.0-liter Euro 6 Ecoboost DISI engine has been tested on a chassis dynamometer using WLTP and Artemis driving cycles, and on the road on a one-hour test loop containing urban, rural and motorway driving. Two isomers of butanol, 1-butanol and 2-methyl-propanol, were each blended with gasoline at 25% volume. Non-oxygenated gasoline and 15% ethanol in gasoline (E15) were used as reference fuels. The vehicle performed well in terms of cold start, drivability, general performance, and off-cycle particle emissions, staying within several mg of particle mass and about 2×1012 particles (per PMP procedure) per km during laboratory tests.

In the diesel sector the fatty acid methyl esters (FAME's) - in Europe mostly RME (rapeseed methyl ester) and in US mostly SME (soja oil methyl ester) - are used as a various share, % volume blends with the diesel fuel (B5, B7, B10, B20, Bxx). The present joint project focuses on RME being the most important representative of the biofuels of 1st generation in Europe. The influences of RME blend fuels on emissions and on lube oil deterioration are emphasized. Emissions were investigated on a modern engine with exhaust gas aftertreatment devices like SCR and (DPF+ SCR). Beside the legally limited exhaust emission components some non-legislated like NO₂, N₂O, NH₃ and nanoparticles were measured at stationary and dynamic engine operation.

Analysis of non-legislated engine-emission components, with different exhaust-gas after-treatment techniques, is an important air quality objective. This paper reports the results for various nitrogen oxides, ammonia and differentiated hydrocarbons emitted at part load from a small 4-S SI engine. It was operated with gasoline, with CNG and with two different three-way catalytic converters. CNG produces less HC and less aromatics. But the HC conversion rate is insufficient. This is due to the lower exhaust gas temperatures, at part load with CNG, and due to the higher stability of light HCs. CNG affects the λ-regulation window, of the investigated system, such that the NOx conversion rate is lowered. In the rich domain of the λ-regulation window, the NO & NOx emissions after catalyst were lowest, while the NH₃ formation was most intense, and vice versa.

Vegetable oils, in their pure form, are increasingly used as a cost-effective, locally produced, renewable fuel. Early results revealed gradual formation of engine deposits while operated on vegetable oils. While current practices, level of sophistication, and results vary among individual “conversions”, the most sophisticated installations operate in dual-fuel mode, with heated vegetable oil introduced into an already warm engine. Heating of the vegetable oil and pre-heating of the engine on ordinary fuel have resulted in operational and emissions improvements. To evaluate the effects on emissions, tests were conducted on several modern private passenger vehicles with direct-injection turbodiesel engines, which were retrofitted with a secondary heated fueling system, but with no other modifications or adjustments to the engines and injection pumps. While operating on vegetable oil, engines generally exhibited slightly lower NOx and higher CO than while compared to diesel fuel.

During the VERT *) testing of different DPF systems it was remarked, that the oxidation catalyst converts sometimes a big part of NO to NO2, producing on the one hand a more toxic composition of the exhaust gases and causing on the other hand measuring artefacts, which tend to underestimate of NO2 and NOx by the cold NOx - measurement. The present work summarizes the experiences in this matter elaborated at the Laboratories for IC-Engines & Exhaust Emissions Control (AFHB) of the University of Applied Sciences Biel-Bienne, Switzerland, during several VERT activities and didactic projects on engine and chassis dynamometers in the years 2000-2006.

Limited and non-regulated emissions of scooters were analysed during several annual research programs of the Swiss Federal Office of Environment (BAFU) *). Small scooters, which are very much used in the congested centers of several cities, are a remarkable source of air pollution. Therefore every effort to reduce the emissions is an important contribution to improve the air quality in urban centers. In the present work detailed investigations of particle emissions of different 2-stroke scooters with direct injection and with carburettor were performed. The nanoparticulate emissions were measured by means of SMPS, (CPC) and NanoMet. Also the particle mass emission (PM) was measured with the same method as for Diesel engines. Extensive analyses of PM-residuum for SOF/INSOF, PAH and toxicity equivalence (TEQ), were carried out in an international project network. Particle mass emission (PM) of 2-S Scooters consists mostly of SOF.

An active oxidation catalyst is an efficient measure to reduce not only gaseous components (CO, HC), but also particle emissions (mostly oil condensates) of a small 2-stroke engine with lost oil lubrication. Since the 2- and 3-wheelers with 2-stroke propulsion are still a very serious source of air pollution worldwide in many urban areas, it is important to have a look on some consequences of an improperly working catalyst. The present paper shows some results of user-oriented aging of catalyst on the vehicle and results of limited emissions and unlimited (nano)particles during the catalysts screening tests. The works are a part of an international scooter network project, which was performed (2004 to 2007) in the Laboratories for IC-Engines & Exhaust Emission Control of the University of Applied Sciences, Biel, Switzerland with main support of the Swiss Federal Office of Environment (BAFU), Swiss Petrol Union (EV) and Swiss Lubes (VSS).

A filter system is presented which allows the reduction of the concentration of ultrafine particles in vehicle cabins to very low levels. The original ventilation system is switched to the recirculation mode and all cabin intake air is supplied via a retrofitted filter system. Tests with a variety of different vehicles (from passenger cars to coaches) show the efficiency of the system.

This paper reports on particulate matter (PM) emissions measurement on a turbocharged direct injection tractor diesel engine with a mechanically controlled injection pump operated alternately on diesel fuel and fuel-grade rapeseed oil heated to 70-90°C. PM emissions were measured using standard gravimetric method, with supplemental online measurements with a semi-condensing integrating forward laser beam scattering detector and a measuring ionization chamber. All three measurements were in good agreement and show that the operation on heated rapeseed oil results, compared to operation on diesel fuel, in moderate decreases in PM emissions at moderate and higher speeds and loads, and substantial increases in PM at low speeds and loads. Low-speed, low-load operation on vegetable oil therefore needs to be addressed even if the engine appears to produce acceptable emissions during standard tests.

2- and 3-wheelers with 2-S propulsion are still a very serious source of air pollution worldwide in many urban areas. Therefore, every effort to reduce the emissions of those vehicles is an important contribution to improve the air quality. In the present work detailed investigations of regulated emissions and of particle emissions of 2-stroke scooters with direct injection and with carburator were performed. To demonstrate the emission reduction potentials some possibilities of emission improvements were grouped into steps. These technical measures were: ○ Higher tier lube oils ○ Lower oil dosing ○ Active oxidation catalyst ○ Supplementary filtration & oxidation devise (WFC) **) ○ Special fuel. Particle mass and nanoparticles (number), which are amply present in 2-stroke exhaust gas and which contribute strongly to the toxicity level are still unlimited by the international exhaust gas legislation. They were extensively investigated in the present project series.

Concern for engine particle emission led to EC regulations of the number of solid particles emitted by LDV and HDV. However, all conventional piston-driven combustion engines emit metal oxide particles of which only little is known. The main sources are abrasion between piston ring and cylinder, abrasion of bearing, cams and valves, catalyst coatings, metal-organic lubrication oil additives, and fuel additives. While abrasion usually generates particles in the μm range, high concentrations of nanosize metal oxide particles are also observed, probably resulting from nucleation processes during combustion. In general, metal oxides, especially from transition metals, have high surface reactivity and can therefore be very toxic, especially nanosize particles, which evidently provide a high specific bioactive surface and are suspected to penetrate into the organism. Hence, these particles must be scrutinized for quantity, size distribution and composition.

The objectives of the present work are to investigate the regulated and unregulated (particle) emissions of a classical and modern 2-stroke and a typical 4-stroke scooter with different ethanol blend fuels. There is also comparison of two different ethanol fuels: pure ethanol (E) *) and hydrous ethanol (EH) which contains 3.9% water and is denatured with 1.5% gasoline. Special attention is paid in this research to the hydrous ethanol, since the production costs of hydrous ethanol are much less than those for (dry) ethanol. The vehicles are with carburettor and without catalyst, which represents the most frequent technology in Eastern Asia and offers the information of engine-out emissions. Exhaust emissions measurements have been performed with fuels containing ethanol (E), or hydrous ethanol (EH) in the portion of 5, 10, 15 and 20% by volume. During the test systematical analysis of particle mass (PM) and nano-particles counts (NP) were carried out.

Different Diesel Particle Filters (DPF)*) were tested on a 2-Stroke Detroit-Diesel bus engine 6V 92 TA. The investigations focused on soot burden and regeneration of the DPF with special filter materials. Also examined was promoting the regeneration by: throttling, additive (FBC), oxidation catalytic converter upstream of DPF and the catalytic coating of the filter material. The metrics were the particulate matter emission, its composition and the nanoparticles. The most important results are: The average SOF content in the engine exhaust particulate matter is 77.6 % and the majority of it is emitted as bigger droplets The wire-mesh filter catalyst (WFC) - a novel emission reduction technology -substantially curtails the SOF and PM. WFC traps and oxidizes the oil droplets and produces a “dry” soot. This can be very advantageous for the DPF downstream of WFC. (WFC can be also very interesting for 2-S gasoline engines).

In order to meet future requirements for emission reduction and fuel economy a variety of concepts are available for gasoline engines. In the recent past new pathways have been found using alternative fuels and fuel combinations to establish cost optimized solutions. The presented concept for a SI-engine consists of combined injection of gasoline and hydrogen. A hydrogen enriched gas mixture is being injected additionally to gasoline into the engine manifold. The gas composition represents the output of an onboard gasoline reformer. The simulations and measurements show substantial benefits to improve the combustion process resulting in reduced cold start and warm up emissions and optimized part load operation. The replacement of gasoline by hydrogen-rich gas during engine start leads to zero hydrocarbons in the exhaust gas.

To complement laboratory emissions tests and to obtain emissions data for events that are difficult to simulate, a portable, on-board mass exhaust emissions monitoring system has been developed. The system utilizes NDIR for CO and CO2, an electrochemical cell for NOx and laser light scattering detectors for PM real-time concentrations measurements. Exhaust flow is determined computationally from engine operating data using mass balance equations. The system is designed to easily and quickly install on a large variety of vehicles, including buses with passengers on board, and to produce a wealth of on-road data with minimal downtime and travel of the vehicle tested.

1 Small off-road 2-stroke SI-engines have very high pollutant emissions. The Swiss environmental protection agency (BUWAL) investigates the state of the technology and emissions with the scope to show the potential of improvements by means of the best available technology (BAT) and to motivate the consumers to use the more sophisticated equipment and cleaner fuels to protect their health and the environment. In the present work emission measurements of chainsaws were performed with a special concern of particulate emissions. Particulates were analysed by means of: gravimetry, SMPS, NanoMet and differential analysis of filter residue. The varied conditions were: A/F-ratio, lube-oil content and the fuel quality. It has been shown, that the particulate mass and the nanoparticle numbers, which both consisting almost exclusively of unburned lube-oil, attain very high values. They are strongly influenced by the mixture tuning and by the lube-oil content.

A well-balanced use of alternative fuels worldwide is an important objective for a sustainable development of individual transportation. Several countries have objectives to substitute a part of the energy of traffic by ethanol as the renewable energy source. The global share of Bioethanol used for transportation is continuously increasing. Investigations of limited and unregulated emissions of a flex fuel vehicle with gasoline-ethanol blend fuel have been performed in the present work on the chassis dynamometer according to the measuring procedures, which were established in the previous research in the Swiss Network to adequately consider the transient (WLTC) and the stationary operation (SSC). The investigated fuel contained ethanol (E), in the portions of 10% & 85% by volume. The investigated vehicle represented a newer state of technology and an emission level of Euro 5. The engine works with homogenous GDI concept and with 3-W-catalyst (3WC).

In this study, the combustion of butanol, neat and mixed with gasoline, was investigated on a 0.6 liter two-cylinder spark ignition engine with fully adjustable fuel injection and spark timing, coupled with an eddy current dynamometer. Two isomers of butanol, n-butanol and iso-butanol, were examined. This basic parameter study gives information about potential requirements of engine control systems for butanol FFV. Compared to the traditionally used ethanol, butanol does not exhibit hygroscopic behaviour, is chemically less aggressive and has higher energy density. On other hand, different laminar burning velocity and higher boiling temperature of butanol, compared to gasoline, requires some countermeasures to keep the engine operation reliable and efficient.

In the present paper some results of investigations of nanoparticles from five DI gasoline cars are represented. The measurements were performed at vehicle tailpipe and in CVS-tunnel. Moreover, five variants of “vehicle - GPF” were investigated. These results originate from the project GasOMeP (Gasoline Organic & Metal Particulates), which focused on metal-nanoparticles (including sub 20nm) from gasoline cars with different engine technologies. The PN-emission level of the investigated GDI cars in WLTC without GPF is in the same range of magnitude very near to the actual limit value of 6.0 × 1012 #/km. With the GPF’s with better filtration quality, it is possible to lower the emissions below the future limit value of 6.0 × 1011 #/km. There is no visible nuclei mode and the ultrafine particle concentrations below 10mm are insignificant. Some of the vehicles show at constant speed operation a periodical fluctuation of the NP-emissions, as an effect of the electronic control.

During the first decade of diesel particle filter development and deployment in cars, trucks, buses and underground sites, DPF regeneration methods were engineered that were compatible with the then prevalent high sulfur content in the fuel ≻ 2000 ppm. The mainly used methods were burners, electrical heaters, replaceable filters and non-precious metal fuel additives. Low sulfur diesel fuel became only available from 1996 in Sweden, 1998 in Switzerland, and after 2000 everywhere in Europe. Thus, the deployment of precious metal catalytic converters was feasible both as original equipment and retrofitting of in-use engines. The so-called CRT particle filters using PGM-catalysis for providing NO₂ for low temperature regeneration became very successful wherever ULSD was available.