Search Results

A laboratory study was performed to optimize a zoned configuration of an iron (Fe) SCR catalyst and a copper (Cu) SCR catalyst in order to provide high NOx conversion at lean A/F ratios over a broad range of temperature for diesel and lean-burn gasoline applications. With an optimized space velocity of 8,300 hr-1, a 67% (by volume) Fe section followed by a 33% Cu section provided at least 80% NOx conversion from approximately 230°C to 640°C when evaluated with 500 ppm NO and NH3. To improve the lean lightoff performance of the SCR catalyst system during a cold start, a Cu SCR catalyst that was 1/4 as long as the rear Cu SCR catalyst was placed in front of the Fe SCR catalyst. When evaluated with an excess of NH3 (NH3/NO ratio of 2.2), the Cu+Fe+Cu SCR system had significantly improved lightoff performance relative to the Fe+Cu SCR system, although the front Cu SCR catalyst did decrease the NOx conversion at temperatures above 475°C by oxidizing some of the NH3 to N2 or NO.

A laboratory study was performed to assess the effects of SO2 poisoning on the NOx conversion of iron (Fe) and copper (Cu) SCR catalysts. Thermally aged samples of the catalysts were poisoned with SO2 under lean conditions. At various times during the poisonings, the samples were evaluated for NOx conversion with NO and NH3 using lean temperature ramps. The low temperature NOx conversions of both catalysts decreased by 10 to 20% after 1 to 4 hours of poisoning but were stable with continued exposure to the SO2. The poisoned Cu SCR catalyst could be desulfated repeatedly with 5 minutes of lean operation at 600°C. Initially, the poisoned Fe SCR catalyst required 5 minutes of lean operation at 750°C to recover its maximum NOx conversion.

A laboratory study was performed to assess the effects of sulfur poisoning and desulfation temperature on the NO conversion of a LNT+(Cu/SCR) in-situ system. Four LNT+(Cu/SCR) systems were aged for 4.5 hours without sulfur at 600, 700, 750, and 800°C using A/F ratio modulations to represent 23K miles of desulfations at different temperatures. NO conversion tests were performed on the LNT alone and on the LNT+SCR system using a 60 s lean/5 s rich cycle. The catalysts were then sulfur-poisoned at 400°C and desulfated four times and re-evaluated on the 60/5 tests. This test sequence was repeated 3 more times to represent 100K miles of desulfations. After simulating 23K miles of desulfations, the Cu-based SCR catalysts improved the NO conversion of the LNT at low temperatures (e.g., 300°C), although the benefit decreased as the desulfation temperature increased from 600°C to 800°C.

A laboratory study was performed to assess the potential of using selective catalytic reduction (SCR) with NH3 to treat the NOx emissions from lean-burn gasoline engines. A primary concern was the potential for hot rich exhaust conditions on the vehicle, as such conditions could degrade the zeolite-based SCR catalysts being developed for automotive applications. Samples of an iron/zeolite formulation were aged for 34 hours behind samples of a three-way catalyst (TWC) on a pulse-flame combustion reactor using different A/F ratio schedules that exposed the catalysts to either continuously lean operation, mostly stoichiometric operation, or mostly rich operation. For each A/F ratio schedule, separate SCR samples were aged with inlet temperatures of 750°C, 800°C, or 850°C. The aged SCR samples were evaluated for NOx conversion at 25K hr-1 during lean temperature ramps with 500 ppm NO and NH3.

A laboratory study was performed to assess the potential capability of TWC+LNT/SCR systems to satisfy the Tier 2, Bin 2 emission standards for lean-burn gasoline applications. It was assumed that the exhaust system would need a close-coupled (CC) TWC, an underbody (U/B) TWC, and a third U/B LNT/SCR converter to satisfy the emission standards on the FTP and US06 tests while allowing lean operation for improved fuel economy during select driving conditions. Target levels for HC, CO, and NOx during lean/rich cycling were established. Sizing studies were performed to determine the minimum LNT/SCR volume needed to satisfy the NOx target. The ability of the TWC to oxidize the HC during rich operation through steam reforming was crucial for satisfying the HC target.

A laboratory study was performed to assess the potential capability of passive TWC+SCR systems to satisfy the Tier 2, Bin 2 emission standards for lean-burn gasoline applications. In this system, the TWC generates the NH3 for the SCR catalyst from the feedgas NOx during rich operation. Therefore, this approach benefits from high feedgas NOx during rich operation to generate high levels of NH3 quickly and low feedgas NOx during lean operation for a low rate of NH3 consumption. It was assumed that the exhaust system needed to include a close-coupled (CC) TWC, an underbody (U/B) TWC, and an U/B SCR converter to satisfy the emission standards during the FTP and US06 tests while allowing lean operation for improved fuel economy during select driving conditions. Target levels for HC, CO, and NOx during lean/rich cycling were established. With a 30 s lean/10 s rich cycle and 200 ppm NO lean, 1500 ppm NO rich and the equivalent of 3.3 L of SCR volume were required to satisfy the NOx target.

This paper summarizes results from a large study on the release of NOx from a lean NOx trap during rich purges. Under certain purge conditions, some NOx trap formulations have the propensity to release some of the NOx stored during previous lean operation without reducing it. This purge NOx release was examined for different NOx trap formulations. The purge NOx release was evaluated for one of the formulations as a function of several variables, including the aging condition of the trap, the trap temperature, the trap volume, the purge A/F ratio, the purge flow rate, and the amount of NOx stored. The effect of hot lean pretreatments on the purge NOx release was studied. In addition, the effect of the rhodium level on the purge NOx release was examined. Mechanisms for the NOx release are proposed that are consistent with the observed data. The results indicate that the purge NOx release is very low for thermally aged traps and is primarily a concern for fresh or stabilized traps.

A laboratory study was performed to assess the effectiveness of LNT+SCR systems for NOx control in lean exhaust. The effects of the catalyst system length and the spatial configuration of the LNT & SCR catalysts were evaluated for their effects on the NOx conversion, NH₃ yield, N₂O yield, and HC conversion. It was found that multi-zone catalyst architectures with four or eight alternating LNT and SCR catalyst zones had equivalent gross NOx conversion, lower NH₃ and N₂O yield, and significantly higher net conversion of NOx to N₂ than an all-LNT design or a standard LNT+SCR configuration, where all of the SCR volume is placed downstream of the LNT. The lower NH₃ emissions of the two multi-zone designs relative to the standard LNT+SCR design were attributed to the improved balance of NOx and NH₃ in the SCR zones.

A study was performed to assess the effects of the catalyst volume and the ceria content in the washcoat on the aged emission performance of underfloor catalytic converters containing platinum and rhodium. Catalyst volumes of 1.4 L and 2.8 L were evaluated, while the ceria level was varied from 0 to 60% of the weight of the washcoat. The concentration of noble metals (g/L) was the same for both catalyst volumes, so the larger volume also contained more noble metal. Catalyst performance was evaluated on an air/fuel ratio sweep test, at steady-state conditions on an engine, and on the FTP test. In light of the new catalyst monitoring requirements for OBD II, each catalyst was also evaluated at steady-state conditions using a dual oxygen sensor technique in order to produce an O2 sensor index. The evaluations were performed at several intermediate stages as the catalysts were aged on engines using high temperature durability schedules intended to simulate high mileage conditions.

A study was undertaken to evaluate the feasibility of using the catalyst exotherm to diagnose the emission performance of the catalytic converter. The exotherm was evaluated as a potential diagnostic for large volume underfloor converters as well as for small volume warmup converters. Emphasis was placed on the ability to properly diagnose the emission performance of the converters while the vehicle was driven under a variety of transient driving schedules. For this study, type K thermocouples were used for measuring the temperatures. To minimize the variability of the exotherm data during transient driving, the exotherm needs to be sampled under fairly stable exhaust flow conditions. If a transient maneuver such as an acceleration occurs, a stabilization time is required before the exotherm can be sampled. The steady-state HC conversion of underfloor catalytic converters correlated well with the exotherm measured at the rear of the catalyst over a large range of conversions.

An engine-based test has been developed to measure the oxygen storage capacity of a catalyst. The test utilizes the difference in the engine-out and tailpipe A/F ratios following rich-to-lean and lean-to-rich A/F transitions in order to quantify the storage or release of oxygen. The technique also results in the determination of the water-gas shift constant for the tailpipe exhaust. The technique was used to measure the oxygen storage capacity of a fresh catalytic converter at inlet temperatures of 400, 500, and 600°C for catalyst volumes of 1.5L and 2.8L. The procedure was repeated after the converter had been aged at an inlet temperature of 800°C for 20, 40, and 60 hours. The oxygen storage capacities are related to the emissions performance of the converter on A/F ratio sweep tests. For the fresh converter, the calculated oxygen storage capacity increased with temperature.

Desulfation characteristics of several model and fully-formulated monolithic lean NOx trap materials were studied in a laboratory flow reactor employing a chemical ionization mass spectrometer. For all samples, desulfation at elevated temperatures under reducing conditions resulted in appearance of sulfur dioxide (SO2) followed by carbonyl sulfide (COS) and hydrogen sulfide (H2S). The data appear consistent with a desulfation mechanism involving elimination of SO2 from stored sulfates under reducing conditions, followed by reaction of the SO2 with CO and H2 to produce COS and H2S, respectively. Based on these observations, several cyclic and multistage desulfation strategies were devised which greatly decreased H2S emissions while achieving relatively rapid and complete sulfur removal.

Selective catalytic reduction (SCR) with NH3 provides an attractive alternative to lean NOx traps for controlling the NOx emissions from lean-burn gasoline engines. This paper summarizes a laboratory study to assess the effects of temperature, space velocity, and the concentrations of NO, NH3, and O2 on the NOx conversion of an iron/zeolite SCR catalyst. A fresh sample was evaluated on slow temperature ramps with 5% O2 and 250, 500, or 1000 ppm of NO and NH3. The NOx conversion at low temperatures decreased with increasing NO and NH3 concentrations due to kinetic limitations. Conversely, the conversion at high temperatures increased with increasing NO and NH3 concentrations because the portion of NH3 oxidized by O2 decreased with increasing NO concentration.