Refine Your Search

Topic

Author

Search Results

Technical Paper

A challenge to vapor distribution measurement of multi-component evaporating fuel spray via laser absorption-scattering (LAS) technique

2007-07-23
2007-01-1892
In the present study, a challenge has been made to quantitatively determine the vapor phase concentration distributions in an evaporating multicomponent fuel spray using the LAS imaging technique. The theoretical considerations were particularly given when applying the LAS imaging technique to the multicomponent fuel spray and reconstructing the vapor concentration distributions from the spray images.
Technical Paper

Effects of Micro-Hole and Ultra-High Injection Pressure on Mixture Properties of D.I. Diesel Spray

2007-07-23
2007-01-1890
Experimental study has been carried out on the effects of the micro-hole nozzle injector and ultra-high injection pressure on the mixture properties of D.I. Diesel engine. A manually operated piston screw pump, High Pressure Generator, was used to obtain ultra-high injection pressures. Three kinds of injection pressures, 100MPa, 200MPa, and 300MPa, were applied to a specially designed injector. Four kinds of nozzle hole diameters, 0.16mm, 0.14mm, 0.10mm, and 0.08mm, were adopted in this study. The laser absorption-scattering (LAS) technique was used to analyze the equivalence ratio distributions, Sauter mean diameter, spray tip penetration length, and other spray characteristics. The analyses of the experimental results show that the micro-hole nozzle and ultra-high injection pressure are effective to increase the turbulent mixing rate and to form the uniform and lean fuel-air mixture.
Technical Paper

Effects of Group-hole Nozzle Specifications on Fuel Atomization and Evaporation of Direct Injection Diesel Sprays

2007-07-23
2007-01-1889
The group-hole nozzle concept is regarded as a promising approach to facilitate better fuel atomization and evaporation for direct injection diesel engine applications. In the present work, the spray and mixture properties of group-hole nozzle with close, parallel or a small included angle orifices were investigated experimentally by means of the ultraviolet-visible laser absorption-scattering (LAS) imaging technique, in comparison with the conventional single-hole nozzle. Three series of group-hole nozzles were designed to investigate the effect of group-hole nozzle specification while varying the included angle and interval between the orifices. The results suggested that: 1) Group-hole nozzle with very close, parallel orifices presents the similar spray characteristics with those of the single-hole nozzle.
Technical Paper

Spray and Mixture Properties of Hole-Type Injector for D. I. Gasoline Engine-Comparison of Experiment and CFD Simulation-

2007-07-23
2007-01-1850
An experimental and numerical study was conducted on the spray and mixture properties of a hole-type injector for direct injection (D. I.) gasoline engines. The Laser Absorption Scattering (LAS) technique was adopted to simultaneously measure the spatial concentration distributions and the mass of the liquid and vapor phases in the fuel spray injected into a high-pressure and high-temperature constant volume vessel. The experimental results were compared to the numerical calculation results using three-dimensional CFD and the multi-objective optimization. In the numerical simulation, the design variable of the spray model was optimized by choosing spray tip penetration, and mass of liquid and vapor phases as objective functions.
Technical Paper

Entrainment, Evaporation and Mixing Characteristics of Diesel Sprays around End-of-Injection

2009-04-20
2009-01-0849
In this study, air entrainment, fuel evaporation and mixing process of diesel sprays injected by micro-orifices for direct-injection diesel engines were investigated at the end of injection transient and after the end of injection. The mixture formation process was analyzed using a laser absorption scattering (LAS) technique, providing the information of quantified liquid and vapor mass concentration, entrained air concentration and equivalence ratio. The data was obtained at the timings of quasi-steady state, sudden velocity decrease, the end of injection and after the end of injection. Two micro-orifices, which have different orifice diameters, were selected as test nozzles to investigate the end-of-injection characteristics at different nozzle geometries. In case of smaller orifice diameter, the liquid phase regression was observed around the end of injection, while it was not observed at larger orifice diameter due to denser liquid concentration near the nozzle tip.
Journal Article

Effect of Injection Pressure on Ignition, Flame Development and Soot Formation Processes of Biodiesel Fuel Spray

2010-09-28
2010-32-0053
The effect of injection pressure ranging from 100 to 300MPa on the ignition, flame development and soot formation characteristics of biodiesel fuel spray using a common rail injection system for direct injection (D.I.) diesel engine was investigated. Experiments were carried out in a constant volume vessel under conditions similar to the real engine condition using a single hole nozzle. Biodiesel fuels from two sources namely; palm oil (BDFp) and cooked oil (BDFc) with the commercial JIS#2diesel fuel were utilized in this research. The OH chemiluminescence technique was used to determine the ignition and the lift-off length of the combusting flame. The natural luminosity technique was applied to study the flame development and the two color pyrometry was applied for the soot formation processes. Ignition delay decreased as the injection pressure progressed from 100 to 300MPa. This was as a result of the enhanced mixing achieved at higher injection pressures.
Technical Paper

Numerical and Experimental Analyses of the Injection Characteristics of Dimethyl Ether with a D. I. Diesel Injection System

1999-03-01
1999-01-1122
The fuel injection characteristics of Dimethyl Ether(DME) were calculated and compared with the calculated results of diesel fuel using a simulation model of an in-line diesel injection system in order to clarify the differences between the injection characteristics of the two fuels. Moreover, numerical analyses for the DME injection were performed while changing the fuel parameters and the injection system parameters in order to estimate the effects of these parameters on the fuel injection characteristics. The effects of some of these parameters were evaluated by experimental results conducted in a constant volume vessel. Furthermore, the spray tip penetration was calculated using the computed results of the injection pressure. As a result of this study, the injection characteristics of the DME fuel are basically confirmed. By the macroscopic analyses of these spray characteristics, the DME spray behavior in a combustion chamber can be estimated.
Technical Paper

Simplified Three-Dimensional Modeling of Mixture Formation and Combustion in a D.I. Diesel Engine

1989-02-01
890269
This paper describes a simplified three-dimensional modeling of the mixture formation and combustion processes in a direct injection (D.I.) diesel engine. The fuel-air mixing and combustion processes in the D.I. diesel engine can be characterized by the combined effects of some processes, such as spray trajectory, fuel vaporization, gas motion, combustion, and dispersion of gaseous components and enthalpy. Each process was computed by a simple sub-model based on the experimental results and empirical equations. The dispersion process was, however, computed by solving the conservation equations of the gaseous components and enthalpy by the finite difference technique. The sub-models were combined for predicting the three-dimensional distributions of the gaseous components and the temperature in the combustion chamber, and finally the cylinder pressure, heat release rate, engine performance and pollutant emissions (NO and soot).
Technical Paper

Fuel Spray Trajectory and Dispersion in a D.I. Diesel Combustion Chamber

1989-02-01
890462
Experiments and modeling of the fuel spray trajectory and dispersion influenced by both a swirling gas flow and wall impingement were performed under simulated direct injection (D.I.) diesel engine conditions at a high pressure and high temperature. A spray was injected into the steady swirling gas flow and impinged on the simulated piston cavity wall in a constant-volume bomb. High-speed Schlieren photographs provided the informative data on the behavior of the spray vaporizing in such diesel-like circumstances. A simplified computational model was developed to describe the spray trajectory and the fuel vapor dispersion in the D.I. diesel combustion chamber. The model includes the effects of the breakup on the trajectory and the vaporization of the spray, and the effects of the swirling gas flow and the wall impingement on the dispersion of the fuel vapor.
Technical Paper

Total In-Cylinder Sampling Experiment on Emission Formation Processes in a D.I. Diesel Engine

1990-10-01
902062
An experimental study on emission formation processes, such as these of nitric oxide, particulate and total hydrocarbon in a small direct injection (D.I.) diesel engine was carried out by using a newly developed total in-cylinder sampling technique. The sampling method consisted of rapidly opening a blowdown valve attached to the bottom of the piston bowl, and quickly transferring most of the in-cylinder contents into a large sampling chamber below the piston. No modification of the intake and exhaust ports in a cylinder head was required for the installation of the blowdown apparatus. The sampling experiment gave a history of spatially-averaged emission concentrations in the cylinder. The effects of several engine variables, such as the length-to-diameter ratio of the nozzle hole, the ratio of the piston bowl diameter to the cylinder bore and the intake swirl ratio, on the emission formation processes were investigated.
Technical Paper

A Practical Calculation Method for Injection Pressure and Spray Penetration in Diesel Engines

1992-02-01
920624
Spray penetration for Diesel injectors, where injection pressure varies with time during the injection period, was calculated. In order to carry out this calculation, the discharge coefficients of the needle-seat opening passage and discharge hole in orifice-type Diesel nozzles were investigated separately. Simple empirical correlations were obtained between these coefficients and needle lift. Then, by introducing these correlations, the injection pressure, which is defined as the pressure in the sac chamber just upstream of the discharge hole, was either derived from measured fuel supply line pressure, or predicted by means of an injection system simulation. Finally, based on the transient injection pressure, spray tip penetration was calculated by taking the overall line which covers the trajectories of all fuel elements ejected during the injection period.
Technical Paper

An Experimental Study on Mixture Formation Process of Flat Wall Impinging Spray Injected by Micro-Hole Nozzle under Ultra-High Injection Pressures

2008-06-23
2008-01-1601
Increasing injection pressure and decreasing nozzle hole diameter have been proved to be two effective approaches to reduce the exhaust emissions and to improve the fuel economy. Recently, the micro-hole nozzles and ultra-high injection pressures are applicable in commercial Diesel engines. But the mechanism of these two latest technologies is still unclear. The current research aims at providing information on the spray and mixture formation processes of the micro-hole nozzle (d=0.08mm) under the ultra-high injection pressure (Pinj=300MPa). The flat wall impinging sprays were focused on and the laser absorption-scattering (LAS) technique was employed to obtain the qualitative and quantitative information at both atmospheric and elevated conditions. The spray parameters were collected, the mixing rate was discussed, and the effects of various parameters on mixture formation were clarified.
Technical Paper

Quantitative Imaging of the Fuel Concentration in a SI Engine with Laser Rayleigh Scattering

1993-10-01
932641
Quantitative imaging of the fuel concentration distribution was made in the combustion chamber of a propane-fueled spark ignition (SI) engine with the employment of laser-sheet-induced Rayleigh scattering technique for realizing the remote, nonintrusive and highly space- and time-resolved measurement. The original engine was modified to introduce YAG laser-induced sheet light into the combustion chamber and the scattered light was captured by a CCD camera fitted with a gated double-micro- channel plate image intensifier. The measurements were done at the crank angle of 270°ATDC in the combustion chamber of the engine motored at 200rpm with an air fuel ratio of 13 for various injection timing, injection direction and intake flow. The results show that with an appropriate matching of fuel injection timing, injection direction and intake flow, a stratified distribution of the fuel concentration can be realized.
Technical Paper

Ignition and Flame Propagation of Spray Compound Mixture

1993-10-01
932711
The ignition and flame propagation processes of a propane-air mixture compounded with a kerosene spray were investigated in order to allow a better understanding of the multi-phase combustion process of the spray compound mixture in a direct injection stratified charge (DISC) engine. The ignition probability and the flame propagation velocity, as functions of the overall equivalence ratio, fraction of propane in the fuel, ignition energy and the Sauter mean diameter of the spray, were measured under atmospheric conditions. The development of the flame kernel and the propagating flame were observed by a high-speed video camera combined with a schlieren system. Adding small amounts of the kerosene spray to the lean propane-air mixture improved the ignition probability. However, the ignition probability depended strongly on the Sauter mean diameter and the ignition energy. Replacing the propane with the kerosene spray in a rich propane-air mixture increased the flame propagation velocity.
Technical Paper

Simultaneous Concentration Measurement of Vapor and Liquid in an Evaporating Diesel Spray

1993-03-01
930863
A new technique was proposed for the simultaneous measurement of the concentration of fuel vapor and liquid in an evaporating diesel spray injected into a high temperature and high pressure environment. This technique was based on the principle of the absorption of ultraviolet laser light by fuel vapor and the scattering of visible laser light by fuel droplets in the diesel spray. For this principle, α-methylnaphthalene was used as a test fuel. Measuring the transmissivity of ultraviolet and visible laser lights absorbed and scattered by β-methylnaphthalene spray made it possible to analyze the fuel vapor concentration, droplets density and the mixture temperature in the diesel spray. A computerized tomographic transfer technique was also adopted to analyze three-dimensional fuel concentration distribution in the spray.
Technical Paper

Approach to Low NOx and Smoke Emission Engines by Using Phenomenological Simulation

1993-03-01
930612
A phenomenological spray-combustion model of a D.I. Diesel engine was applied to study the engine parameters with potential for reducing NOx and smoke emissions. The spray-combustion model, first developed at the University of Hiroshima in 1976, has been sophisticated by incorporating new knowledge of diesel combustion. The model was verified using data from an experimental, single cylinder, D.I. diesel engine with a bore of 135mm and a stroke of 130mm. After the verification process, calculations were made under a wide range of the engine parameters, such as intake air temperature, intake air pressure, intake swirl ratio, nozzle hole diameter, injection pressure, air entrainment rate into the spray, and injection rate profile. These calculations estimated the effects of the engine parameters on NOx, smoke and specific fuel consumption. As a result of the calculations, an approach for the low NOx and smoke emission engine was found.
Technical Paper

An Analysis of Ambient Air Entrainment into Split Injection D.I. Gasoline Spray by LIF-PIV Technique

2002-10-21
2002-01-2662
Effects of split injection, with a relatively short time interval between the two sprays, on the spray development process, and the air entrainment into the spray, were investigated by using laser induced fluorescence and particle image velocimetry (LIF-PIV) techniques. The velocities of the spray and the ambient air were measured. The cumulative mass of the ambient air entrained into the spray was calculated by using the entrainment velocity normal to the spray boundary. The vortex structure of the spray, formed around the leading edge of the spray, showed a true rotating flow motion at low ambient pressures of 0.1 MPa, whereas at 0.4 MPa, it was not a true rotating flow, but a phenomenon of the small droplets separating from the leading edge of the spray and falling behind, due to air resistance. The development processes of the 2nd spray were considerably different from that of the 1st spray because the 2nd spray was injected into the flow fields formed by the 1st spray.
Technical Paper

Characterization of Combustion Processes in the Prechamber and Main Chamber of an Indirect Injection Diesel Engine by High-Speed Photography

1986-09-01
861181
The combustion processes in the prechamber and the main chamber of a small indirect injection (I.D.I.) diesel engine were observed simultaneously by high-speed photography. These observations made it possible to characterize the behavior of flames in both chambers, that is, ignition of fuel, developing and rotating flames in the prechamber, and a flame jet spouting into the main chamber. The effect of engine variables, such as fuel injection timing, cross-sectional area of a throat, fuel injector location, and a recess in a piston top, on the combustion process as well as the engine performance were considered. A flame jet spouting into the main chamber separated into two directions and induced two vortexes. Brown sooty flames appeared along the prechamber wall and inside the flame jet which struck on the piston top. The higher-velocity flame jet and the two Intense vortexes induced by the flame jet realized superior fuel consumption and lower smoke emission.
Technical Paper

A Visual Study of D.I. Diesel Combustion from the Under and Lateral Sides of an Engine

1986-09-01
861182
A high-speed photographic study is presented illustrating the influence of engine variables such as an introduced air swirl, the number of nozzle holes and the piston cavity diameter, on the combustion process in a small direct-injection (D.I.) diesel engine. The engine was modified for optical access from the under and lateral sides of the combustion chamber. This modification enabled a three-dimensional analysis of the flame motion in the engine. The swirling velocity of a flame in a combustion chamber was highest in the piston cavity, and outside the piston cavity it became lower at the piston top and at the cylinder head in that order. The swirl ratio of the flame inside the cavity radius attenuated gradually with piston descent and approached the swirl ratio outside the cavity radius, which remained approximately constant during the expansion stroke. Engine performance was improved by retarding the attenuation of the swirl motion inside the cavity radius.
Technical Paper

Three-Dimensional Spray Distributions in a Direct Injection Diesel Engine

1994-09-01
941693
Experiments and modeling of a spray impinged onto a cavity wall of a simulated piston were performed under simulated diesel engine conditions (pressure and density) at an ambient temperature. The diesel fuel was delivered from a Bosch-type injection pump to a single-hole nozzle, the hole being drilled in the same direction as the original five-hole nozzle. The fuel was injected into a high-pressure bomb in which an engine combustion chamber, composed of a piston, a cylinder head and a cylinder liner, was installed. Distributions of the spray impinged on the simulated combustion chamber were observed from various directions while changing some of the experimental parameters, such as combustion chamber shape, nozzle projection and top-clearance. High-speed photography was used in the constant volume bomb to examine the effect of these parameters on the spray distributions.
X