Search Results

On the basis of the large amount of know-how accumulated in the field of automotive ethanol SI-engine fuelling in Brazil, it seemed appropriate to continue and set a new milestone in the usage of ethanol fuel. The paper presents the preliminary study made to enable the transfer of the ethanol technology to a 5.9-liter 4-cylinder boxer aircraft engine. The study describes the steps made to define the optimal parameter configuration for the transfer of the fuel system packaging, the fuel injector layout, the engine control unit (ECU) and the legislative redundancy requirements for aviation applications. The paper illustrates the use of numerical simulation techniques and special visualization approaches necessary to understand the physical phenomena of mixture preparation (spray atomization and momentum). Two different layouts are presented and discussed and a certain number of experimental results obtained with the retained solution are presented and discussed.

The suggestions for upcoming Euro 2000 clean air act puts an increasing legislative pressure for lower specific fuel consumption in order to reduce the emission of CO2 and thereby decrease the impact of the “green house” effect. One of the possible suggestions to meet these requirements for SI-engines is the gasoline direct injected (GDI) power unit. One of the key points of the success of a layout of a GDI system is the optimization of the fuel injector and combustion chamber charge formation parameters. A brief description of the basic GDI-system used during the study is given. Hereafter are outlined the computational and experimental optimization tools which have been used to produce, on a reasonable industrial time scale, the main indications to optimize the design of a given injector/chamber configuration. The paper discusses in detail the results produced by the latest enhancements introduced into the 3D multi-phase computational approach, NCF-3D.

The paper presents the main reasons for the increasing market share of vehicles with the capacity to run on random bio fuel blends. It describes the philosophy and basic layout of current integral flex mixture preparation systems. The paper demonstrates the necessity to introduce a series of new high-performance analysis tools for further improvement of the mixture preparation system and in particular the fuel injector performance. The paper continues with a discussion of the basic structure of the interactive Virtual Engine Model approach applied to fuel injector atomizer optimization. Test results obtained by application of the new tools to two different series production flex engines are presented. The impact of the improved spray formation capability of the optimized fuel injector atomizers is explained and experimental vehicle FTP-cycle data are reported and discussed.

The paper presents a description of the development phases of the new third generation of “green” fuel injectors. The development objective for the new PICO-ECOlogical injector was to define a layout, which enables an optimal parameter configuration for both the mixture preparation (high flexibility to adapt different atomizer plate structures) and the manufacturing processes. It is demonstrated in which way the use of high-level numerical simulation and visualization techniques have become an integrated part of the development process. A detailed description is given of the new layout with respect to earlier versions and the advantageous new features obtained are discussed. Test results obtained by the new 3rd-generation injector layout are presented. The impact of the improved dynamic response capability is explained and experimental data at both engine test rig and vehicle FTP-cycle conditions are reported and discussed.

The success obtained by use of Virtual Engine Modeling (VEM) in the design and development areas of fuel injectors generated a lot of interest from production and quality engineers to dispose of a similar tool related to spray vessel measurements. To respond to stringent PL6/EURO5 requirements it was decided to develop a Virtual Spray Vessel (VSV) tool capable of predicting spray patters and perform droplet diameter analysis comparable to Phase Doppler Analysis (PDA) results. The paper describes the analogies between VEM and VSV modeling, the specific new numerical approaches to obtain spatial spray data comparable to conventional mechanical measurement techniques and to perform droplet diameter analysis comparable to PDA data. The paper concludes with a series of comparisons of simulated and experimental data.

The paper presents a study of the influence of fuel pressure supply fluctuations on the upstream side of the fuel injector atomizer. The study is performed over a wide range of pressures (70 to 130 Mpa) with two different common-rail (CR) high-pressure fuel injectors. The common atomizer is a VCO-type equipped with conically shaped atomizer bores. With the injector tip (nozzle) mounted in a counter-pressure vessel the pressure fluctuations in the fuel-rail and in the injector body are recorded simultaneously with stroboscopic Schlieren-visualization of the time-resolved spray behavior. It is demonstrated that not only the instantaneous mass flow is affected. As a function of rail-pressure, pulse-width and injection strategy the pressure fluctuations change the spray hard-core structure and its break-up behavior.

The first part of the paper gives an overview of the current results obtained with the first-generation of GDI-powered vehicles launched on the European market. In view of the rather limited success in fuel consumption gain the second-generation of very lean stratified layouts has begun, but this process requires the development and application of new high-level analysis tools. A possible high performance approach is the multi-purpose use of 3-D numerical simulation both in the development and the engine control strategy calibration phases. The development of a small 1.6 liter lean stratified engine project was chosen to demonstrate the dual application capability of the NCF-3D simulation tool. The paper continues with a description of the engine application frame, the basic features of the NCF-3D simulation tool and the latest enhancements made to combustion and fuel composition models within the software frame.

The new European legislation on two-wheeler pollutant emissions has forced two stroke engine manufacturers to study the direct fuel injection (DI) technology. The Piaggio “ET2 Injection” was the first DI engine in production, using the FAST system (Fully Atomized Stratified Turbulence) applied on a 50 cm3 engine. Within the framework of the DOLCE project (Development Of innovative Low pollutant, noise and fuel Consumption two stroke spark ignition Engines for future vehicles for individual urban mobility) coordinated by Piaggio and supported by the European Commission, a 125 cm3 direct injection 2-stroke engine was developed. This paper presents the engine-related part of this work, which was concluded in March 2000. The engine is equipped with the FAST system and the fuel metering is performed by means of a low-pressure electronic fuel injection system integrated in an Engine Management System (EMS) specially developed for this type of application.

The first part of the paper gives an overview of the environmental conditions with which a future two stroke engine must comply. The reasons for which a direct gasoline injection into the combustion chamber offers one of the most promising solutions are explained. In order to understand the potential of different GDI-layouts to produce very lean stratified combustion behavior two different approaches are studied in detail. The latest version of the fuel/air mixture injection used by the F. A. S. T. engine is confronted with a basically liquid high-pressure layout, similar to the design used in automotive four-stroke passenger car engines. A description is given of the basic fluid dynamics of the 50 cc engine used for the study as well as of the experimental and numerical tools applied. The paper concludes with a detailed presentation of the obtained results as well as of the arguments retained to produce the final rating.

In the present paper the impact of three different geometrical layouts of the discharge nozzle of a high-pressure diesel injector designed is examined for a common rail second generation direct injection system. The paper presents a comparative study of the spray behavior of the three different nozzle layouts connected to a 150 MPa rail-pressure when mounted on a 1.6 liter European passenger car engine. To evaluate experimentally the differences in the fundamental physical spray parameters several specially developed optical visualization techniques are used, which enable phase-Doppler, Laser-sheet and high-speed recordings of dense high pressure sprays. The change in basic spray parameters (time-resolved droplet distribution and spray momentum) caused by the nozzle geometry variation is examined. The impact on the in-cylinder penetration and mixing characteristics is studied with a 3D-numerical simulation code NCF-3D.

Experimental measurements and numerical computations were made to characterize a spray generated by a high-pressure swirl injector. The Phase Doppler technique was applied to get information on droplet sizes (d10) and axial velocities at defined distances from the injector tip. Global spray visualization was also made. Computations were carried out using a modified version of KIVA 3V. In particular, the break-up length of the sheet and its dimension were computed from a semi-empirical correlation related to the wave instability theory suggested by Dombrowski, including the modifications introduced by Han and Reitz. Two different approaches were used to describe the initial spray conditions. According to the first, discrete particles with a characteristic size equal to the thickness of the sheet are injected. The second approach assumes, that the particles having a SMD computed by a semi-empirical correlation are injected according to a statistical distribution.

The first part of the paper gives an overview of the results obtained with European GDI-powered vehicles launched on the market. Thereafter, a discussion of in-vehicle limitations due to the exhaust gas after-treatment system requirements is given. The paper continues with a description of the current development status of European lean stratified direct injection system layouts. A detailed presentation is made of the mixture preparation system key components, basic control algorithms and the necessary new high-level experimental and analytical development tools. Particularly the topic of the multi-purpose use of 3-D numerical simulation is addressed both in the development and the engine control strategy calibration phases. The development of a small 1.6 liter lean stratified engine project is taken as example to demonstrate the dual application capability of the 3D simulation tool.

In the present paper are examined the consequences of a substantial rise in the injection pressure for Gasoline Direct Injection (GDI) injector assemblies. The paper presents a comparative study of the spray behavior of two different injector nozzle layouts submitted to current 10 Mpa rail-pressure as well as to a 30 Mpa injection pressure. To evaluate the differences in the fundamental physical spray parameters are used several specially developed optical visualization techniques, which enable phase-Doppler, PIV, Laser-sheet and high-speed recordings of dense high pressure fuel sprays. A recently developed injector actuator and the necessary modifications to existing high-pressure pumps to reach a 30 MPa pressure level in the fuel system are presented. The change in basic spray parameters (time-resolved droplet distribution and spray momentum) caused by the rail-pressure rise is examined.

The paper presents a study of a key-element in the mixture preparation process. A typical common-rail (CR) high-pressure fuel injector was fitted with a prototype injector nozzle with atomizer bores of a particular conical layout. It is demonstrated within certain layout limits, that a considerable enhancement can be obtained for the secondary break-up of the hard-core fluid sprays produced by the nozzle. The impact on the combustion process is examined in terms of pressure and heat release as well as of the engine-out pollutant emission. The results are compared to those of an earlier developed CR high-pressure injector nozzle. The atomization behavior of the prototype nozzle is illustrated through experimental results in terms of engine-out emissions from a 1.3-liter turbo-charged passenger car diesel engine. The detailed spray behavior is visualized on a component test rig by use of specially developed optical visualization techniques.

The paper presents the background research on the physics of the droplet coalescence phenomena carried out by an interactive usage of high-level 3-D numerical simulation tools and high-level optical visualization and measurement techniques. The presentation continues with the description of a new injector atomizer plate layout, which enables a physical coalescence control of the droplet population within the entire fuel spray. Finally are presented examples of the impact on exhaust emissions of the introduction the new atomizer plate with coalescence control by engine test bed experiments (steady state low load conditions) and vehicle tests (first cold part of the FTP-cycle).

The present paper describes a study, which can enable a small displacement (1.3 liter) turbocharged European CR-diesel engine to tolerate an important increase in EGR-level. The analysis is performed by use of a 3D virtual numerical engine model, which isolates the main parameters that must be optimized within the perimeter of the combustion chamber. The paper gives a short introduction to the physical background for NOx and soot-formation as well as a recall of the main issues related to the simulation models used in the virtual engine simulation. The analysis is performed in a 9 points load/speed test matrix. Several EGR-rates are studied as well as the impact of a precise temperature control of the exhaust gas re-introduced in the intake manifold. The paper concludes by an analysis of the cumulated impact on the EGR-level tolerated by the engine after the introduction of the suggested optimization measures.

In order to improve the atomization capability of a standard port fuel injector, an optimized suggestion for an air shrouded injector is presented. The fluid dynamic part of the retained solution is composed of a special flat seat design for the fuel metering function combined with a post atomization adapter enabling both mono- and multi-spray modes. The concept works equally well in natural manifold gradient mode and with an external pressure pump. The realized concept is tested in both free jet experiments and on two different 2 litre engines, one operated in stoechiometric conditions the other in lean-burn conditions. The experimental work confirms a potential of the concept to increase torque stability and thereby lean-burn limits, decrease required spark advance and enable open inlet valve injection and consequently decrease wall wetting phenomena.

In the future generation of low consumption SI-engine layouts, it has become necessary to reduce costs as well as the complexity level and, increase the system reliability by the latter. To avoid driving the GDI-system in the critical, very lean stratified operation mode without losing the fuel consumption benefit, a solution is suggested, which combines a fully variable valve control system with a low level, robust GDI combustion layout. The first part of the present paper presents the latest development in the field of high precision multi-hole GDI injector spray nozzles. The basic aspects of mixture preparation with multi-hole gasoline atomizers are highlighted and their spray behavior compared to that of the current swirl atomizer nozzle. The second part of the paper presents primary optimization of a largely homogeneous GDI combustion layout combined with a fully variable valve timing control system including complete cylinder de-activation.

The paper describes the application of laser sheet flow visualisation with numerical image analysis as a useful complementary tool to numerical simulation techniques for the optimisation of fluid dynamics within SI-engine in-take systems. The lay-out of the laser sheet visualisation system and the applied numerical image analysis are discussed in detail. Two applicative examples are given, one of smoke induced visualisation of the internal gas flow of an intake manifold, the other of natural visualisation of fuel injector wall film deposit in the intake runner. Finally is concluded that the addition of visualisation techniques to the development strategy allows a time gain, because it contributes to a rapid understanding of complex flow phenomena.

The paper gives a short introduction to the notion of flex fuel approach for diesel engines. The paper continues with a description of a basic study of the diesel combustion process to allow the design of a strategy for recognition of a random bio-diesel fraction, Bx, by a purely software-based sensing technique, which creates an image of the temporal combustion behavior and uses only sensors already in service for current CR-mixture preparation systems. The paper concludes presenting a series of experimental verification data obtained on a large-scale series produced 1.3 liter Turbo-charged CR-rail passenger car engine.