Search Results

A method for non-intrusive measurement of spark plug fouling, burn quality, pre-ignition and spark characteristics is described. The technique relies on a continuous monitoring of the leakage current to the spark plug centre electrode, via a high voltage diode stand off arrangement. By way of demonstration, the system operation is reported for investigations of cold start plug fouling.

Recent studies in the USA have revealed that the catalysts (which are universally fitted to gasoline automobiles) are failing in service to an unacceptable extent. Although the reasons for the failures are not completely clear, it seems that misfiring, leading to highly exothermic reaction in the catalyst, may be responsible for the damage. Legislation is to be enacted later in this decade to address this problem by requiring on board diagnostic (OBD) systems which can measure misfire, as well as catalyst hydrocarbon (HC) conversion efficiency. Although some ideas have been suggested for the OBD requirements, no fully satisfactory sensor technology has yet appeared. This paper describes a novel hydrocarbon sensor based on a surface catalysis principle. The fundamental studies reported here have been made with the automobile application in mind. A catalytic chemi-ionisation model is proposed in order to enhance our understanding of this surface ionisation.

One of the limits on the maximum fuel efficiency benefit to be gained from turbocharged, downsized gasoline engines is the occurrence of low speed pre-ignition (LSPI). LSPI may lead to high pressures and extreme knock (megaknock or superknock) which can cause severe engine damage. Though the mechanism leading to megaknock is not completely resolved, LSPI is thought to arise from local auto-ignition of areas in the cylinder which are rich in low ignition delay “contaminants” such as engine oil and/or heavy ends of gasoline. These contaminants are introduced to the combustion chamber at various points in the engine cycle (e.g. entering from the top land crevice during blow-down or washed from the cylinder walls during DI wall impingement). This paper describes a method for testing the propensity of different contaminants to cause a local pre-ignition in a gasoline engine. During one cycle, a small amount of contaminant is injected into one cylinder of a 4 cylinder engine.

Recent work has investigated the use of O₂ concentration in the intake manifold as a control variable for diesel engines. It has been recognized as a very good indicator of NOX emissions especially during transient operation, however, much of the work is concentrated on estimating the O₂ concentration as opposed to measuring it. This work investigates Universal Exhaust Gas Oxygen (UEGO) sensors and their potential to be used for such measurements. In previous work it was shown that these sensors can be operated in a controlled pressure environment such that their response time is of the order 10 ms. In this paper, it is shown how the key causes of variation (and therefore potential sources of error) in sensor output, namely, pressure and temperature are largely mitigated by operating the sensors in such an environment. Experiments were undertaken on a representative light-duty diesel engine using modified UEGO sensors in the intake and exhaust system.

This paper describes a novel catalytic oxidation sensor which represents an attempt to realise a practical sensor for on vehicle detection of catalyst efficiency and misfire. Via experimental and modelling approaches, promising characteristics are established, which could mean that an application to the on-vehicle detection of catalyst efficiency and misfire is feasible.

This paper describes a system for real-time smoke detection in diesel engines. Preliminary results are presented from a very simple sensor which detects the net charge level on smoke particles. There appears to be a useful correlation between the peak charge level and the Bosch smoke number. The mechanism by which the particulates is discussed, though no firm conclusions are reached.

Two new techniques are introduced for measuring the residual gas fraction in internal combustion engines. Both techniques use a fast chemiluminescent detection (CLD) type NO sensor. The measurement is made in real-time and requires a single misfire of the engine. Development of the techniques revealed several unexpected, but interesting effects; the results obtained show good agreement with existing knowledge.

One of the limits on the maximum fuel efficiency benefit to be gained from turbocharged, downsized gasoline engines is the occurrence of pre-ignitions at low engine speed. These pre-ignitions may lead to high pressures and extreme knock (megaknock or superknock) which can cause severe engine damage. Though the mechanism leading to megaknock is not completely resolved, pre-ignitions are thought to arise from local autoignition of areas in the cylinder which are rich in low ignition delay “contaminants” such as engine oil and/or heavy ends of gasoline. These contaminants are introduced to the combustion chamber at various points in the engine cycle (e.g. entering from the top land crevice during blow-down or washed from the cylinder walls during DI wall impingement).

This paper presents experimental data showing unexpected transient behaviour in several production universal exhaust gas oxygen (UEGO) sensors. The spike-like transients occur when passing through the stoichiometric point, and are particularly significant when passing from rich to lean. The paper illustrates how the spikes are affected by exhaust gas flow rate, deviation of air-to-fuel ratio (AFR) from stoichiometry, and rate of change of AFR while passing through stoichiometry. The spikes are most sensitive to the rate at which AFR passes through stoichiometry. Brief discussions on possible causes for the spikes, and on undesirable consequences for feedback control applications, are included.