Search Results

The cylinder of the aluminum engine block without iron sleeve was coated directly with thin thermal barrier coatings of zirconia and chrome oxide. The cylinder head and valve face and the piston crown were also coated. These three engine components were tested individually and together. The fuel consumption performance of this 84 x 70 mm direct injection diesel engine improved 10% with only coated cylinder bore. When the fuel injection timing of the coated cylinder bore engine was retarded by about 2°CA, emissions characteristics were approximately the same level as for the baseline engine with 8% improvement in brake specific fuel consumption compared with the baseline engine. At constant fuel flow rate to the engine, the exhaust and cylinder head temperatures were higher for the insulated bore case. One can summarize the combustion temperature must have been higher and heat release rates were faster in the insulated case.

The trend toward lighter vehicles for improved performance has recently introduced the use of aluminum and plastic materials for vehicle bodies and drive trains. In particular, the aluminum alloy block for engine application is certain to reappear. The soft aluminum cylinder liner will require additional treatment before acceptance. Three possible approaches appear to solve the aluminum cylinder liner dilemma. These approaches are: 1. Use of high silicon aluminum such as the 390 aluminum. 2. Insert or cast steel liners into the aluminum engine block. 3. Ceramic coat the low cost standard aluminum engine block. Each has known advantages and disadvantages. It is the purpose of this paper to present the merits of Option 3, the ceramic coated aluminum cylinder bore from the standpoint of low weight, cost, and tribological effectiveness. The advantages of approaches (1) and (2) are obvious. High temperature after treatment of the ceramic engine components is not required.

The experimental emissions testing of a turbocharged six cylinder Caterpillar 3116 diesel engine converted to the Miller cycle operation was conducted. Delayed intake valve closing times were also investigated. Effects of intake valve closing time, injection time, and insulation of piston, head, and liner on the emission characteristics of the Miller cycle engine were experimentally verified. Superior performance and emission characteristic was achieved with a LHR insulated engine. Therefore, all emission and performance comparisons are made with LHR insulated standard engine with LHR insulated Miller cycle engine. Particularly, NOx, CO2, HC, smoke and BSFC data are obtained for comparison. Effect of increasing the intake boost pressure on emission was also studied. Poor emission characteristics of the Miller cycle engine are shown to improve with increased boost pressure. Performance of the insulated Miller cycle engine shows improvement in BSFC when compared to the base engine.

Of late Direct Injection Spark Ignition (DISI) engines are replacing the carburetted SI engines due to certain inherent advantages like uniform distribution of fuel-air mixture in all cylinders in multi cylinder engines. However the homogeneity of the mixture depends on the time of injection as well as the type of fuel injector. It is expected that late in the compression stroke the fuel-air mixture near the spark plug should be a combustible mixture. In order to achieve this, proper air motion during induction and compression is a must. Further the interaction of fuel and air from the start of injection is equally important. This paper addresses these issues. For this a CFD study has been carried out. The injection timings selected are 90, 180 and 2700 aTDC, the idea being to understand the effects of early or late injection on fuel air mixing. The appropriate governing equations are solved using finite volume method. RNG k-ε turbulence model is used for physical modelling.

A gas turbine combustion system is an embodiment of all complexities that engineering equipment can have. The flow is three dimensional, swirling, turbulent, two phase and reacting. The design and development of combustors, until recent past, was an art than science. If one takes the route of development through experiments, it is quite time consuming and costly. Compared to the other two components viz., compressor and turbine, the combustion system is not yet completely amenable to mathematical analysis. A gas turbine combustor is both geometrically and fluid dynamically quite complex. The major challenge a combustion engineer faces is the space constraint. As the combustion chamber is sandwiched between compressor and turbine there is a limitation on the available space. The critical design aspect is in facing the aerodynamic challenges with minimum pressure drop. Accurate mathematical analysis of such a system is next to impossible.

This paper deals mainly with the computer simulation and experimental investigations on a single cylinder, four-stroke, spark ignited, extended expansion engine. The simulation procedure involves thermodynamic and global modeling techniques. Sub-models have been used for predicting heat transfer, friction and gas exchange processes. A two-zone model is adopted for combustion process. Combustion model predicts mass burning rate, ignition delay and combustion duration. It uses sub-models for calculating flame-front area, flamespeed and chemical equilibrium composition of ten product species. Experimentally measured valve-lift data along with suitable coefficient of discharge is used in the analysis of gas exchange process. Unburned hydrocarbons, carbon monoxide and nitric oxide emissions have also been predicted. Experiments have been conducted on a single cylinder, air-cooled, four-stroke, spark-ignition engine.

The global flow characteristics such as mean velocity, turbulence intensity and scales of turbulence have been measured in a swirl combustion chamber of a Compression Ignition engine using a constant temperature hot-wire anemometer. The experiments were conducted at 400 rpm under motoring (non-firing) conditions. Ensemble averaging procedure was adopted to calculate the mean velocity and turbulence intensity after comparing the merits and demerits of this method with the Individual Cycle Mean method and the Frequency Separation method. The experimental results indicate that the mean velocity and turbulence intensity show significant spatial and temporal variations in the swirl chamber. These variations are observed to be maximum from 60 deg. bTDC to TDC of compression. The values of mean velocity at chamber periphery are found to be higher than the values near the chamber axis.

Of late direct injection engines are replacing carburetted and port injected engines due to their high thermal efficiency and fuel economy. One of the reasons for the increased fuel economy is the ultra lean mixture with which the engine operates under low loads. Under the low load conditions, the air fuel ratio of the mixture near the spark plug is close to stoichiometric values while the overall mixture is lean, which is called stratified mixture. In order to achieve this, proper air motion during the late stages of compression is a must. Quality of the mixture depends on the time of injection as well as the type of fuel injector and mixture preparation strategy used. Engines employing air guided mixture preparation are considered as the second generation engines. For understanding the efficient mixture preparation method, three types of flow structures like base (low tumble), high tumble and inclined swirl are created inside the engine cylinder using shrouds on the intake valves.

This paper deals with the analysis of heat release characteristics of an insulated turbocharged, six cylinder, DI contemporary diesel engine. The engine is fully insulated with thin thermal barrier coatings. Effect of insulation on the heat release was experimentally verified. Tests were carried over a range of engine speeds at 100%, 93%, 75% and 50% of rated torque. Fuel injection system was instrumented to obtain injection pressure characteristics. The study shows that rate of heat release, particularly in the major portion of the combustion, is higher for the insulated engine. Improvement in heat release and performance are primarily attributed to reduction in heat transfer loss due to the thin thermal barrier coating. Injection pressure at the rated speed and torque was found to be 138 MPa and there was no degradation of combustion process in the insulated engine. Improvements in BSFC at 93% load are 3.25% and 6% at 1600 and 2600 RPM, respectively.

A high output experimental single cylinder diesel engine that was fully coated and insulated with a ceramic slurry coated combustion chamber was tested at full load and full speed. The cylinder liner and cylinder head mere constructed of 410 Series stainless steel and the top half of the articulated piston and the cylinder head top deck plate were made of titanium. The cylinder liner, head plate and the piston crown were coated with ceramic slurry coating. An adiabaticity of 35 percent was predicted for the insulated engine. The top ring reversal area on the cylinder liner was oil cooled. In spite of the high boost pressure ratio of 4:1, the pressure charged air was not aftercooled. No deterioration in engine volumetric efficiency was noted. At full load (260 psi BMEP) and 2600 rpm, the coolant heat rejection rate of 12 btu/hp.min. was achieved. The original engine build had coolant heat rejection of 18.3 btu/hp-min and exhaust energy heat rejection of 42.3 btu/hp-min at full load.

This paper investigates theoretically the effects of heat transfer characteristics, such as crank-angle phasing and wall temperature swings, on the thermodynamic efficiency of an IC engine. The objective is to illustrate the fundamental physical basis of applying thin thermal barrier coatings to improve the performance of military and commercial IC engines. A simple model illustrates how the thermal impedance and thickness of coatings can be manipulated to control heat transfer and limit the high temperatures in engine components. A friction model is also included to estimate the overall improvement in engine efficiency by the proper selection of coating thickness and material.

This paper investigates theoretically the benefits of the Miller cycle diesel engine with and without low heat rejection on thermodynamic efficiency, brake power, and fuel consumption. It further illustrates the effectiveness of thin thermal barrier coatings to improve the performance of military and commercial IC engines. A simple model which includes a friction model is used to estimate the overall improvement in engine performance. Miller cycle is accomplished by closing the intake valve late and the engine components are coated with PSZ for low heat rejection. A significant improvement in brake power and thermal efficiency are observed.

Thermal barrier coatings are becoming increasingly important in providing thermal insulation for heat engine components. Thermal insulation reduces in-cylinder heat transfer from the engine combustion chamber as well as reducing component structural temperatures. Containment of heat also contributes to increased in-cylinder work and offers higher exhaust temperatures for energy recovery. Lower component structural temperatures will result in greater durability. Advanced ceramic composite coatings also offer the unique properties that can provide reductions in friction and wear. Test results and analysis to evaluate the performance benefits of thin thermal barrier coated components in a single cylinder diesel engine are presented.

The objective of present study is to predict and analyze the flow through the Carburettor for two different throttle opening conditions. The studies have been carried out by Computational Fluid Dynamics (CFD) software and the prediction has been validated with experimental data. Three dimensional geometrical models of two different throttle positions namely 50% opening and wide open throttle (100% throttle opening) were created using the commercially available software. The mesh was generated using the Tet-hybrid scheme which includes primarily of tetrahedral mesh elements but may also include hexahedral, pyramidal and wedge elements. The pressure boundary conditions are used to define the fluid pressure at the inlet and outlet of the carburettor. The steady state flow field analysis inside a carburettor has been simulated using the Multiphase mixture model and Langrangian Discrete phase model.

Aldehyde formation and emissions from alcohol fueled engines are studied and presented in this paper. Several chemical kinetic models on the mechanism leading to aldehyde formation have been examined to explore the appropriate control methods to reduce exhaust aldehyde emissions. Control of aldehydes in exhaust emissions by suitable alteration of engine operating parameters, by in cylinder treatment with additives like aniline and water, by external treatment like airpreheating, secondary air injection cooling water rate and exhaust treatment are examined. The concept of surface ignition for alcohol fuels is briefly presented as a long range objective for using alcohols with minimal aldehyde emissions.

This paper describes the progress on the Cummins-TARADCOM adiabatic turbocompound diesel engine development program. An adiabatic diesel engine system adaptable to the use of high performance ceramics which hopefully will enable higher operating temperatures, reduced heat loss, and turbo-charged exhaust energy recovery is presented. The engine operating environments as well as the thermal and mechanical loadings of the critical engine components are covered. Design criteria are presented and techniques leading to its fulfillment are shown. The present shortcomings of the high performance ceramic design in terms of meeting reliability and insulation targets are discussed, and the needs for composite designs are shown. A ceramic design methodology for an insulated engine component is described and some of the test results are shown. Other possible future improvements such as the minimum friction-unlubricated engine through the use of ceramics are also described.

A Minimum Cooled Engine (MCE) has been successfully run for 250 hours at rated condition of 298 kW and 1900 rpm. This engine was all metallic without any coolant in the block and lower part of the heads. Ring/liner/lubricant system and thermal loading on the liner at top ring reversal (TRR) as well as on the piston are presented and discussed. Ring/liner wear is given as well as oil consumption and blow-by data during the endurance run. Another engine build with a different top ring coating and several lubricants suggested that a 1500 hours endurance run of MCE is achievable. Rig test data for screening ring materials and synthetic lubricants necessary for a successful operation of a so-called Adiabatic Engine with the ring/ceramic liner (SiN) interface temperature up to 650°C are presented and discussed.

This paper discusses the goals, progress, and future plans of the TACOM/Cummins Adiabatic Engine Program. The Adiabatic Engine concept insulates the diesel combustion chamber with high temperature materials to allow hot operation near an adiabatic operation condition. Additional power and improved efficiency derived from this concept occur because thermal energy, normally lost to the cooling and exhaust systems, is converted to useful power through the use of turbomachinery and high-temperature materials. Engine testing has repeatedly demonstrated the Adiabatic Engine to be the most fuel efficient engine in the world with multi-cylinder engine performance levels of 0.285 LB/BHP-HR (48% thermal efficiency) at 450 HP representative. Installation of an early version of the Adiabatic Engine within a military 5 ton truck has been completed, with initial vehicle evaluation successfully accomplished.

A new self lubricating material has been assessed in a laboratory rig simulating high temperature piston rings for adiabatic diesel engines. The material consists of a solid metallic surface containing half millimetre diameter pockets filled with solid lubricant. The friction and wear properties of conventional piston ring surfaces were assessed at 380°C versus a chromium oxide counterface. This was followed by a study of the properties of various solid lubricant formulations which were then evaluated as fillers for surface pockets. The most promising solid lubricated materials contained molybdenum disulphide or lithium fluoride plus copper.

Contrary to the thick thermal barrier coating approach used in adiabatic diesel engines, the authors have investigated the merits of thin coatings. Transient heat transfer analysis indicates that the temperature swings experienced at combustion chamber surfaces depend primarily on material thermophysical properties, i.e., conductivity, density, and specific heat. Thus, cyclic temperature swings should be alike whether thick or thin (less than 0.25 mm) coatings are applied, Furthermore, thin coatings would lead to lower mean component temperatures and would be easier to apply than thick coatings. The thinly-coated engine concept offers several advantages including improved volumetric efficiency, lower cylinder liner wall temperatures, improved piston-liner tribological behavior, and improved erosion-corrosion resistance and thus greater component durability.