Search Results

Knock is one of the main limitations on Spark-Ignited (SI) Internal Combustion Engine (ICE) performance and efficiency and so has been the object of study for over one hundred years. Great strides have been made in terms of understanding in that time, but certain rather elementary practical problems remain. One of these is how to interpret if a running engine is knocking and how likely this is to result in damage. Knocking in a development environment is typically quantified based on numerical descriptions of the high frequency content of a cylinder pressure signal. Certain key frequencies are observed, which Draper [1] explained with fundamental acoustic theory back in 1935. Since then, a number of approaches of varying complexity have been employed to correlate what is happening within the chamber with what is measured by a pressure transducer.

In recent years, internal combustion engine (ICE) downsizing coupled with turbocharging was considered the most effective path to improve engine efficiency at low load, without penalizing rated power/torque performance at full load. On the other side, issues related to knocking combustion and excessive exhaust gas temperatures obliged adopting countermeasures that highly affect the efficiency, such as fuel enrichment and delayed combustion. Powertrain electrification allows operating the ICE mostly at medium/high loads, shifting design needs and constraints towards targeting high efficiency under those operating conditions. Conversely, engine efficiency at low loads becomes a less important issue. In this track, the aim of this work is the investigation of the potential of the oversizing of a small Variable Valve ActuationSpark Ignition gasoline engine towards efficiency increase and tailpipe emission reduction.

Engine knock is emerging as the main limiting factor for modern spark-ignition (SI) engines, facing increasing thermal loads and seeking demanding efficiency targets. To fulfill these requirements, the engine operating point must be moved as close as possible to the onset of abnormal combustion events. The turbulent regime characterizing in-cylinder flows and SI combustion leads to serious fluctuations between consecutive engine cycles. This forces the engine designer to further distance the target condition from its theoretical optimum, in order to prevent abnormal combustion to severely damage the engine components just because of few individual heavy-knocking cycles. A RANS-based model is presented in this study, which is able to predict not only the ensemble average knock occurrence but also a knock probability. This improves the knock tendency characterization, since the mean knock onset alone is a poorly meaningful indication in a stochastic event such as engine knock.

New SI engine generations are characterized by a simultaneous reduction of the engine displacement and an increase of the brake power; such targets are achieved through the adoption of several techniques such as turbocharging, direct fuel injection, variable valve timing and variable port lengths. This design approach, called “downsizing”, leads to a marked increase in the thermal loads acting on the engine components, in particular on those facing the combustion chamber. Hence, an accurate evaluation of the thermal field is of primary importance in order to avoid mechanical failures. Moreover, the correct evaluation of the temperature distribution improves the prediction of pointwise abnormal combustion onset.

The occurrence of knock is the most limiting hindrance for modern Spark-Ignition (SI) engines. In order to understand its origin and move the operating condition as close as possible to onset of this potentially harmful phenomenon, a joint experimental and numerical investigation is the most recommended approach. A preliminary experimental activity was carried out at IM-CNR on a 0.4 liter GDI unit, equipped with a flat transparent piston. The analysis of flame front morphology allowed to correlate high levels of flame front wrinkling and negative curvature to knock prone operating conditions, such as increased spark timings or high levels of exhaust back-pressure. In this study a detailed CFD analysis is carried out for the same engine and operating point as the experiments. The aim of this activity is to deeper investigate the reasons behind the main outcomes of the experimental campaign.

The detailed study of part-load conditions is essential to characterize engine-out emissions in key operating conditions. The relevance of part-load operations is further emphasized by the recent regulations such as the new WLTP standard. Combustion development at part-load operations depends on a complex interplay between moderate turbulence levels (low engine speed and tumble ratio), low in-cylinder pressure and temperature, and stoichiometric-to-lean mixture quality (to maximize fuel efficiency). From a modelling standpoint, the reduced turbulence intensity compared to full-load operations complicates the interaction between different sub-models (e.g., reconsideration of the flamelet hypothesis adopted by common combustion models). In this article, the authors focus on chemistry-based simulations for laminar flame speed of gasoline surrogates at conditions typical of part-load operations. The analysis is an extension of a previous study focused on full-load operations.

Conventional fossil fuels are more and more regulated in terms of both engine-out emissions and fuel consumption. Moreover, oil price and political instabilities in oil-producer countries are pushing towards the use of alternative fuels compatible with the existing units. N-Butanol is an attractive candidate as conventional gasoline replacement, given its ease of production from bio-mass and key physico-chemical properties similar to their gasoline counterpart. A comparison in terms of combustion behavior of gasoline and n-Butanol is here presented by means of experiments and 3D-CFD simulations. The fuels are tested on a single-cylinder direct-injection spark-ignition (DISI) unit with an optically accessible flat piston. The analysis is carried out at stoichiometric undiluted condition and lean-diluted mixture for both pure fuels.

The paper investigates the low-temperature cranking operation of a current production automotive Gasoline Direct Injected (GDI) by means of 3D-CFD simulations. Particular care is devoted to the analysis of the hollow cone spray evolution within the combustion chamber and to the formation of fuel film deposits on the combustion chamber walls. Due to the high injected fuel amount and the strongly reduced fuel vaporization, wall wetting is a critical issue and plays a fundamental role on both the early combustion stages and the amount of unburnt hydrocarbons formation. In fact, it is commonly recognized that most of the unburnt hydrocarbon emissions from 4-stroke gasoline engines occur during cold start operations, when fuel film in the cylinder vaporize slowly and fuel can persist until the exhaust stroke.

The paper presents a numerical activity directed at the analysis and optimization of internal combustion engine water cooling jackets, with particular emphasis on the fatigue-strength assessment and improvement. In the paper, full 3D-CFD and FEM analyses of conjugate heat transfer and load cycle under actual engine operation of a single bank of a current production V6 turbocharged diesel engine are reported. A highly detailed model of the engine, made up of both the coolant galleries and the surrounding metal components, i.e., the engine head, the engine block, the gasket, the valve guides and valve seats, is used on both sides of the simulation process to accurately capture the influence of the cooling system layout under thermal and load conditions as close as possible to actual engine operations.

High power-density Diesel engines are characterized by remarkable thermo-mechanical loads. Therefore, compared to spark ignition engines, designers are forced to increase component strength in order to avoid failures. 3D-CFD simulations represent a powerful tool for the evaluation of the engine thermal field and may be used by designers, along with FE analyses, to ensure thermo-mechanical reliability. The present work aims at providing an integrated in-cylinder/CHT methodology for the estimation of a Diesel engine thermal field. On one hand, in-cylinder simulations are fundamental to evaluate not only the integral amount of heat transfer to the combustion chamber walls, but also its point-wise distribution. To this specific aim, an improved heat transfer model based on a modified thermal wall function is adopted to estimate correctly wall heat fluxes due to combustion.

The paper investigates the idle operating condition of a current production turbocharged Gasoline Direct Injected (GDI) high performance engine both from an experimental and a numerical perspective. Due to the low engine speed, to the low injection pressure and to the null contribution of the turbocharger, the engine condition is far from the standard points of investigation. According to the low heat flux due to combustion, temperature levels are low and reduced fuel evaporation is expected. Consequently, fuel spray evolution within the combustion chamber and spray/wall interaction are key points for the understanding of the combustion process. In order to properly investigate and understand the many complex phenomena, a wide set of engine speeds was experimentally investigated and, as far as the understanding of the physics of spray/wall interaction is concerned, many different injection strategies are tested.

The paper reports the application of Proper Orthogonal Decomposition (POD) to LES calculations for the analysis of combustion and knock tendency in a highly downsized turbocharged GDI engine that is currently under production. In order to qualitatively match the cyclic variability of the combustion process, Large-Eddy Simulation (LES) of the closed-valve portion of the cycle is used with cycle-dependent initial conditions from a previous multi-cycle analysis [1, 2, 3]. Detailed chemical modelling of fuel's auto-ignition quality is considered through an ad-hoc implemented look-up table approach, as a trade-off between the need for a reasonable representation of the chemistry and that of limiting the computational cost of the LES simulations. Experimental tests were conducted operating the engine at knock-limited spark advance (KLSA) and the proposed knock model was previously validated for such engine setup [3].

The paper describes an integrated methodology for the accurate characterization of the thermal behavior of internal combustion engines, with particular reference to a high performance direct injected SI engine for sport car applications. The engine is operated at full load and maximum power revving speed, which is known to be critical from the point of view of thermal stresses on the engine components. In particular, two different sets of 3D-CFD calculations are adopted: on one side, full-cycle in-cylinder analyses are carried out to estimate the point wise thermal heat flux due to combustion on the engine components facing the combustion chamber. On the other side, full-engine multi-region CHT calculations covering the engine coolant jacket and the surrounding metal components are used to compute the point wise temperature distribution within the engine head, liner and block.

The paper reports the application of LES multi-cycle analysis for the characterization of cycle to cycle variability (hereafter CCV) of a highly downsized DISI engine for sport car applications. The analysis covers several subsequent engine cycles operating the engine at full load, peak power engine speed. Despite the chosen engine operation is usually considered relatively stable, relevant fluctuations were experimentally measured in terms of in-cylinder pressure evolution and combustion phasing. On one hand, despite the complex architecture of the V-8 engine, the origin of such CCV is considered to be poorly related to cyclic fluctuations of the gas-dynamics within the intake and exhaust pipes, since acquisitions of the instantaneous pressure traces at both the intake port entrance and exhaust port junction by fast-response pressure measurements over 250 subsequent engine cycles showed almost negligible differences in both amplitude and phasing compared to those within the cylinder.

Polymer Electrolyte Membrane Fuel Cell (PEMFC) are among the most promising technologies as energy conversion devices for the transportation sector due to their potential to eliminate, or greatly reduce, the production of greenhouse gases. One of the current issues with this type of technology is thermal management, which is a key aspect in the design and optimization of PEMFC, whose main aim is an effective and balanced heat removal, thus avoiding thermal gradients leading to a cell lifetime reduction as well as a decrease in the output performance. In addition, a uniform temperature distribution contributes to the achievement of a uniform current density, as it affects the rate of the electrochemical reaction. This is made even more challenging due to the low operating temperature (80°C), reducing the temperature difference for heat dissipation, and leaving a critical role to the design and optimization of the cooling circuit design.

The accurate representation of Internal Combustion Engine (ICE) flows via CFD is an extremely complex task: it strongly depends on a combination of highly impacting factors, such as grid resolution (both local and global), choice of the turbulence model, numeric schemes and mesh motion technique. A well-founded choice must be made in order to avoid excessive computational cost and numerical difficulties arising from the combination of fine computational grids, high-order numeric schemes and geometrical complexity typical of ICEs. The paper focuses on the comparison between different mesh motion technologies, namely layer addition and removal, morphing/remapping and overset grids. Different grid strategies for a chosen mesh motion technology are also discussed. The performance of each mesh technology and grid strategy is evaluated in terms of accuracy and computational efficiency (stability, scalability, robustness).

In spark-ignited direct-injected engines, the formation of fuel pools on the piston is one of the major promoters of unburnt hydrocarbons and soot: in order to comply with the increasingly stringent emission regulations (EU6 and forthcoming), it is therefore necessary to limit fuel deposit formation. The combined use of advanced experimental techniques and detailed 3D-CFD simulations can help to understand the mechanisms driving fuel pool formation. In the paper, a combined experimental and numerical characterization of pool formation in a GDI engine is carried out to investigate and understand the complex interplay of all the mentioned factors. In particular, a low-load low-rpm engine operation is investigated for different ignition phasing, and the impact of both fuel formulation and instantaneous piston temperature variations in the CFD analyses are evaluated.

A new generation of highly downsized SI engines with specific power output around or above 150 HP/liter is emerging in the sport car market sector. Technologies such as high-boosting, direct injection and downsizing are adopted to increase power density and reduce fuel consumption. To counterbalance the increased risks of pre-ignition, knock or mega-knock, currently made turbocharged SI engines usually operate with high fuel enrichments and delayed (sometimes negative) spark advances. The former is responsible for high fuel consumption levels, while the latter induce an even lower A/F ratio (below 11), to limit the turbine inlet temperature, with huge negative effects on BSFC. A possible solution to increase knock resistance is investigated in the paper by means of 3D-CFD analyses: water/methanol emulsion is port-fuel injected to replace mixture enrichment while preserving, if not improving, indicated mean effective pressure and knock safety margins.

Engine downsizing is gaining popularity in the high performance engine market sector, where a new generation of highly downsized engines with specific power outputs around or above 150 HP/litre is emerging. High-boost and downsizing, adopted to increase power density and reduce fuel consumption, have to face the increased risks of pre-ignition, knock or mega-knock. To counterbalance autoignition of fuel/air mixture, such engines usually operate with high fuel enrichments and delayed (sometimes negative) spark advances. The former is responsible for high fuel consumption levels, while the latter reduces performance and induces an even lower A/F ratio (below 11), to limit the turbine inlet temperature, with huge negative effects on BSFC.

In order to improve fuel conversion efficiency, currently made spark-ignited engines are characterized by the adoption of gasoline direct injection, supercharging and/or turbocharging, complex variable valve actuation strategies. The resulting increase in power/size ratios is responsible for substantially higher average thermal loads on the engine components, which in turn result in increased risks of both thermo-mechanical failures and abnormal combustion events such as surface ignition or knock. The paper presents a comprehensive numerical methodology for the accurate estimation of knock tendency of SI engines, based on the integration of different modeling frameworks and tools. Full-cycle in-cylinder analyses are used to estimate the point-wise heat flux acting on the engine components facing the combustion chamber.