Search Results

Homogeneous charge compression ignition (HCCI) engines have the potential for high fuel efficiency and low NOx emissions. The major disadvantage of HCCI remains the narrow operating range. One way to extend the operating range of HCCI combustion to lower load is to inject part of the total fuel mass into the hot gas during recompression. With even lower engine load, part of the fuel can also be injected late in the main compression and ignited by a spark. The propagating flame further compresses the remaining fuel-air mixture until auto-ignition occurs (spark-assisted HCCI). In this study we investigated the effect of fuel reforming and spark assist in a gasoline engine with direct fuel injection and negative valve overlap. We performed experiments with different injection quantities and varying injection timings during recompression.

Homogenous Charge Compression Ignition (HCCI) combustion offers efficiency improvements compared to conventional gasoline engines. However, due to the nature of HCCI, traditional HCCI combustion can be realized only in a limited operating range. The HCCI operation at high load is limited by excessive combustion noise. In order to maximize the fuel economy benefits of HCCI its operating range needs to be extended to higher loads. In particular, one immediate benefit of an increased load range on the NEDC driving cycle is the avoidance of transitions between SI operation and HCCI operation. In this research a detailed investigation of the fundamental reasons for high combustion noise was performed. Spark-assisted HCCI combustion was found to be a key factor to reduce combustion noise at high load condition.

Boosted Homogeneous Charge Compression Ignition (HCCI) has been modeled and has demonstrated the potential to extend the engine's upper load limit. A commercially available engine simulation software (GT-PowerÖ) coupled to the University of Michigan HCCI combustion and heat transfer correlations was used to model a 4-cylinder boosted HCCI engine with three different boosting configurations: turbocharging, supercharging and series turbocharging. The scope of this study is to identify the best boosting approach in order to extend the HCCI engine's operating range. The results of this study are consistent with the literature: Boosting helps increase the HCCI upper load limit, but matching of turbochargers is a problem. In addition, the low exhaust gas enthalpy resulting from HCCI combustion leads to high pressures in the exhaust manifold increasing pumping work. The series turbocharging strategy appears to provide the largest load range extension.

This article presents an investigation of the sources combustion-generated noise and its measurement in HCCI engines. Two cylinder-pressure derived parameters, the Combustion Noise Level (CNL) and the Ringing Intensity (RI), that are commonly used to establish limits of acceptable operation are compared along with spectral analyses of the pressure traces. This study focuses on explaining the differences between these two parameters and on investigating the sensitivity of the CNL to the ringing/knock phenomenon, to which the human ear is quite sensitive. Then, the effects of independently varying engine operating conditions such as fueling rate, boost pressure, and speed on both the CNL and RI are studied. Results show that the CNL is not significantly affected by the high-frequency components related to the ringing/knock phenomenon.

This study explores the use of two conventional ignition improvers, 2-ethylhexyl nitrate (EHN) and di-tert-butyl peroxide (DTBP), to enhance the autoignition of the regular gasoline in an homogeneous charge compression ignition (HCCI) engine at naturally aspirated and moderately boosted conditions (up to 180 kPa absolute) with a constant engine speed of 1200 rpm. The results showed that both EHN and DTBP are very effective for reducing the intake temperature (Tin) required for autoignition and for enhancing stability to allow a higher charge-mass fuel/air equivalence ratio (ϕm). On the other hand, the addition of these additives can also make the gasoline too reactive at some conditions, so significant exhaust gas recirculation (EGR) is required at these conditions to maintain the desired combustion phasing. Thus, there is a trade-off between improving stability and reducing the oxygen available for combustion when using ignition improvers to extend the high-load limit.

A detailed understanding of the various factors affecting the trends in gross-indicated thermal efficiency with changes in key operating parameters has been carried out, applied to a one-liter displacement single-cylinder boosted Low-Temperature Gasoline Combustion (LTGC) engine. This work systematically investigates how the supplied fuel energy splits into the following four energy pathways: gross-indicated thermal efficiency, combustion inefficiency, heat transfer and exhaust losses, and how this split changes with operating conditions. Additional analysis is performed to determine the influence of variations in the ratio of specific heat capacities (γ) and the effective expansion ratio, related to the combustion-phasing retard (CA50), on the energy split. Heat transfer and exhaust losses are computed using multiple standard cycle analysis techniques. The various methods are evaluated in order to validate the trends.

Low-temperature gasoline combustion (LTGC), based on the compression ignition of a premixed or partially premixed dilute charge, can provide thermal efficiencies (TE) and maximum loads comparable to those of turbo-charged diesel engines, and ultra-low NOx and particulate emissions. Intake boosting is key to achieving high loads with dilute combustion, and it also enhances the fuel's autoignition reactivity, reducing the required intake heating or hot residuals. These effects have the advantages of increasing TE and charge density, allowing greater timing retard with good stability, and making the fuel ϕ- sensitive so that partial fuel stratification (PFS) can be applied for higher loads and further TE improvements. However, at high boost the autoignition reactivity enhancement can become excessive, and substantial amounts of EGR are required to prevent overly advanced combustion.

Low-temperature gasoline combustion (LTGC) has the potential to provide gasoline-fueled engines with efficiencies at or above those of diesel engines and extremely low NOx and particulate emissions. Three key performance goals for LTGC are to obtain high loads, reduce the boost levels required for these loads, and achieve high thermal efficiencies (TEs). This paper reports the results of an experimental investigation into the use of partial fuel stratification, produced using early direct fuel injection (Early-DI PFS), and an increased compression ratio (CR) to achieve significant improvements in these performance characteristics. The experiments were conducted in a 0.98-liter single-cylinder research engine. Increasing the CR from 14:1 to 16:1 produced a nominal increase in the TE of about one TE percentage unit for both premixed and Early-DI PFS operation.

Homogenous Charge Compression Ignition (HCCI) combustion offers significant efficiency improvements compared to conventional spark ignition engines. However, due to the nature of HCCI combustion, traditional HCCI combustion can be realized only in a limited operating range. In order to maximize fuel economy benefits the HCCI operating range needs to be extended to higher loads. One immediate benefit is to maximize the portion of the standard driving cycles (NEDC, FTP, etc.) that can be run with HCCI combustion, so that transitions between SI operation and HCCI operation can be avoided. The HCCI operation at high load range is typically limited by a trade-off between combustion noise and combustion stability. In a previous research, we showed how to improve this trade-off using spark-assisted HCCI combustion strategy, and concluded that the HCCI high load operation is limited by the air availability due to a low lift cam when spark-assisted HCCI combustion was applied.

Homogenous Charge Compression Ignition (HCCI) engines offer a good potential for achieving high fuel efficiency while virtually eliminating NOx and soot emissions from the exhaust. However, realizing the full fuel economy potential at the vehicle level depends on the size of the HCCI operating range. The usable HCCI range is determined by the knock limit on the upper end and the misfire limit at the lower end. Previously proven high sensitivity of the HCCI process to thermal conditions leads to a hypothesis that combustion chamber deposits (CCD) could directly affect HCCI combustion, and that insight about this effect can be helpful in expanding the low-load limit. A combustion chamber conditioning process was carried out in a single-cylinder gasoline-fueled engine with exhaust re-breathing to study CCD formation rates and their effect on combustion. Burn rates accelerated significantly over the forty hours of running under typical HCCI operating conditions.

More stringent emissions regulations are continually being proposed to mitigate adverse human health and environmental impacts of internal combustion engines. With that in mind, it has been proposed that vehicular particulate matter (PM) emissions should be regulated based on particle number in addition to particle mass. One aspect of this project is to study different sample handling methods for number-based aerosol measurements, specifically, two different methods for removing volatile organic compounds (VOCs). One method is a thermodenuder (TD) and the other is an evaporative chamber/diluter (EvCh). These sample-handling methods have been implemented in an engine test cell with a spark-ignited direct injection (SIDI) engine. The engine was designed for stoichiometric, homogeneous combustion.

Multi-dimensional computations were made of spark-ignited premixed-charge combustion in two engines having pent-roof-shaped combustion chambers and two intake valves per cylinder, one with a central spark plug and the other with dual lateral spark plugs. The basic specifications for the two engines were the same except for differences in the number of spark plugs and exhaust valves. The effects of swirl and equivalence ratio on combustion, wall heat transfer, and nitric oxide emission characteristics were examined using a global combustion model that accounts for laminar-kinetics and turbulent-mixing effects. The initial conditions on both mean-flow and turbulence parameters at intake valve closing (IVC) were estimated in order to simulate engine operation either with both intake valves active or with one valve deactivated. The predictions were compared with experimentally derived pressure-time, heat loss, and nitric oxide emission data.

This study utilized a 4-valve engine under HCCI combustion conditions. Each side of the split intake port was fed independently with different temperatures and reactant compositions. Therefore, two stratification approaches were enabled: thermal stratification and compositional stratification. Argon was used as a diluent to achieve higher temperatures and stratify the in-cylinder temperature indirectly via a stratification of the ratio of specific heats (γ = cp/cv). Tests covered five operating conditions (including two values of A/F and two loads) and four stratification cases (including one homogeneous and three with varied temperature and composition). Stratifications of the reactants were expected to affect the combustion control and upper load limit through the combustion phasing and duration, respectively. The two approaches to stratification both affect thermal unmixedness. Since argon has a high γ, it reached higher temperatures through the compression stroke [1].

Engines operating in Homogeneous Charge Compression Ignition (HCCI) combustion mode offer significant benefits of high fuel economy and low engine-out NOx emissions over the conventional spark ignition (SI) combustion mode. However, due to the nature of HCCI combustion, traditional HCCI combustion can be realized only in a limited operating range. High load is limited by the trade-off between ringing (combustion noise) and stability (COV of IMEP). Low load is restricted by the trade-off between NOx emissions and combustion stability (standard deviation of IMEP). The present research is focused on the extension of lo w load limit of HCCI combustion by developing HCCI idle operation. The main obstacle in developing HCCI idle combustion is lack of available thermal energy necessary for successful auto-ignition.

Extending the operating range of the gasoline HCCI engine is essential for achieving desired fuel economy improvements at the vehicle level, and it requires deep understanding of the thermal conditions in the cylinder. Combustion chamber deposits (CCD) have been previously shown to have direct impact on near-wall phenomena and burn rates in the HCCI engine. Hence, the objectives of this work are to characterize thermal properties of deposits in a gasoline HCCI engine and provide foundation for understanding the nature of their impact on autoignition and combustion. The investigation was performed using a single-cylinder engine with re-induction of exhaust instrumented with fast-response thermocouples on the piston top and the cylinder head surface. The measured instantaneous temperature profiles changed as the deposits grew on top of the hot-junctions.

Homogenous Charge Compression Ignition (HCCI) combustion offers significant efficiency improvements compared to conventional gasoline engines. However, due to the nature of HCCI combustion, traditional HCCI engines show some degree of sensitivity to in-cylinder thermal conditions; thus higher cylinder-to-cylinder variation was observed especially at low load and high load operating conditions due to different injector characteristics, different amount of reforming as well as non-uniform EGR distribution. To address these issues, a cylinder balancing control strategy was developed for a multi-cylinder engine. In particular, the cylinder balancing control strategy balances CA50 and AF ratio at high load and low load conditions, respectively. Combustion noise was significantly reduced at high load while combustion stability was improved at low load with the cylinder balancing control.

Homogeneous Charge Compression Ignition (HCCI) combustion is known for its significant fuel economy benefit with near-zero NOx and particulate emissions. Stable HCCI combustion relies on a well-controlled temperature and composition of the cylinder charge at the intake valve closing that in turn requires a precise coordination of all engine inputs. In this paper, the HCCI combustion is realized by retaining hot residual from the previous combustion event using the recompression valve strategy. The recompression valve strategy closes the exhaust valves before the top dead center and opens the intake valves at an angle symmetric to the exhaust valve closing. Depending on the engine load, different valve open/close timings with respect to the crank position are used to trap different amounts of residual gases. It is critical to coordinate the change in the valve open/close timings with the change in the injected fuel quantity during load transients in order to maintain stable combustion.

An existing multidimensional in-cylinder flow code, KIVA, was modified to conduct port-and-cylinder gas flow, fuel spray, and combustion calculations in a port-fuel-injection engine. The effect of a moving valve with a stem was modeled using a novel internal obstacle technique in which the valve was represented by a group of discrete computational particles. Previously developed spray and combustion models were used to simulate fuel injection and combustion processes for a solid-cone shaped, pressure-atomized spray with isooctane as the fuel. The spray model was further modified to handle interactions between the spray drops and the valve. The model was applied to a generic port-fuel-injection engine with variations in port orientation, spray cone angle, and valve configuration (without and with a 180-degree shroud).

Combustion and flow were calculated in a spark-ignited two-stroke crankcase-scavenged engine using a laminar and turbulent characteristic-time combustion submodel in the three-dimensional KIVA code. Both premixed-charge and fuel-injected cases were examined. A multi-cylinder engine simulation program was used to specify initial and boundary conditions for the computation of the scavenging process. A sensitivity study was conducted using the premixed-charge engine data. The influence of different port boundary conditions on the scavenging process was examined. At high delivery ratios, the results were insensitive to variations in the scavenging flow or residual fraction details. In this case, good agreement was obtained with the experimental data using an existing combustion submodel, previously validated in a four-stroke engine study.

As vehicle fuel economy requirements continue to increase it is becoming more challenging and expensive to simultaneously improve fuel consumption and meet emissions regulations. The Passive Ammonia SCR System (PASS) is a novel aftertreatment concept which has the potential to address NOx emissions with application to both lean SI and stoichiometric SI engines. PASS relies on an underfloor (U/F) SCR for storage of ammonia which is generated by the close-coupled (CC) TWCs. For lean SI engines, it is required to operate with occasional rich pulses in order to generate the ammonia, while for stoichiometric application ammonia is passively generated through the toggling of air/fuel ratio. PASS serves as an efficient and cost-effective enhancement to standard aftertreatment systems. For this study, the PASS concept was demonstrated first using lab reactor results which highlight the oxygen tolerance and temperature requirements of the SCR.