Refine Your Search

Topic

Search Results

Standard

Glossary of Fiberboard Terminology

2009-04-20
HISTORICAL
J947_200904
This information report presents the terminology and definitions as used in the fiberboard industry.
Standard

Glossary of Fiberboard Terminology

2003-09-25
HISTORICAL
J947_200309
This information report presents the terminology and definitions as used in the fiberboard industry.
Standard

Glossary of Fiberboard Terminology

1985-01-01
HISTORICAL
J947_198501
A broad general term for fibrous structures produced on any of the several types of fiber forming machines. The primary composition of these boards is normally refined cellulosic or matted wood fibers which may or may not be supplemented by the use of synthetic materials or chemical additives. The manufacture of fiberboards normally involves the formation of a wet web of suspended fibers, which is subsequently pressed, dried, and often calendared or laminated to develop desired end use properties.
Standard

Glossary of Fiberboard Terminology

1980-07-01
HISTORICAL
J947_198007
This information report presents the terminology and definitions as used in the fiberboard industry.
Standard

Felts - Wool and Part Wool

2012-08-24
CURRENT
J314_201208
This SAE Standard identifies chemical/mechanical properties, thickness, width, mass, and other requirements recommended for felts (refer to Tables 1 and 2). It was developed with the cooperation of the Standardization Committee of the Felt Association, Inc., and in accordance with the ASTM tests indicated in the document. The commercial trade designations of the more commonly used grades of automotive felts are given along with complete specifications and tolerances for thickness, mass, wool content, chemical and physical requirements, color, and width. General information, recommended uses, etc., are published in Appendix A as a guide in the selection of felts for particular uses, but the requirements for each application should be taken into consideration in making final selections.
Standard

Test for Chip Resistance of Surface Coatings

2012-10-23
CURRENT
J400_201210
This SAE Recommended Practice covers a laboratory procedure for testing and evaluating the resistance of surface coating to chipping by gravel impact. The test is designed to reproduce the effect of gravel or other media striking exposed paint or coated surfaces of an automobile and has been correlated with actual field results. The specific intent of the test is to evaluate organic surface coatings or systems on flat test panels; however, It may be possible to extend this type of testing to finished parts or other types of materials such as anodized aluminum or plated plastics if the results are interpreted with respect to the limitations and intent implied by the original testing procedures and rating system. This document may involve hazardous materials, operations, and equipment. This document does not purport to address all of the safety problems associated with its use.
Standard

Outdoor Weathering of Exterior Materials

2012-04-16
CURRENT
J1976_201204
This test method specifies the exposure racks, black boxes, and instrumentation, which shall be used for the outdoor weathering of materials for automotive exterior application.
Standard

Test Method for Determining Blocking Resistance and Associated Characteristics of Automotive Trim Materials

2012-10-15
CURRENT
J912_201210
This test method is designed to indicate the degree of surface tackiness, color transfer, loss of embossment, and surface marring when two trim materials are placed face to face under specific conditions of time, temperature, and pressure. These specific conditions are not dictated in this test procedure but will be found in the material standards which govern each type of trim material to be tested.
Standard

Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Water-Cooled Xenon Arc Apparatus

2008-01-11
CURRENT
J1960_200801
This test method specifies the operating procedures for a controlled irradiance, water-cooled xenon arc apparatus used for the accelerated exposure of various automotive exterior materials. This standard is limited to the models of xenon arc test apparatus specified in the Section on Apparatus. All other models of xenon arc test apparatus must use SAE J2527 to perform the test conditions specified in SAE J1960. SAE J2527 is the performance standard based on the test parameters of SAE J1960. Use of xenon arc test apparatus to perform SAE J2527 must be agreed upon by contractual parties.
Standard

Seam Damage Test Procedure

2014-05-20
CURRENT
J1531_201405
This procedure is used to determine seam strength and seam fatigue of automotive textiles, vinyl coated fabrics and related soft trim materials.
Standard

Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Air-Cooled Xenon-Arc Apparatus

2012-11-19
CURRENT
J2019_201211
This SAE Standard specifies the operating procedures for a controlled irradiance, air-cooled xenon-arc apparatus used for the accelerated exposure of various automotive exterior materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
X