Refine Your Search

Topic

Affiliation

Search Results

Technical Paper

Soot Diagnostics Using Laser-Induced Incandescence within an Optically Accessible HSDI Diesel Engine

2004-03-08
2004-01-1412
An optically-accessible single cylinder small-bore HSDI diesel engine equipped with a Bosch common-rail injection system is used to study the effects of differing injection strategies on combustion and soot. Laser-Induced Incandescence (LII) is used to visualize the evolution and distribution of soot within the combustion chamber from the onset of ignition to late into the expansion stroke. A low-sooting fuel, blended from two single component fuels, is used for experimentation. Because of the low-sooting nature of the fuel blend, the lean operating conditions, and optical distortion of the complex shaped engine, acceptable LII signal levels are difficult to obtain. Therefore a low-sulfur European Diesel fuel is also employed during experimentation. Acceptable LII signal levels are obtained using the Diesel fuel, however, without extreme caution, surface damage to the optical components of the engine are possible.
Technical Paper

Spray Combustion of Biodiesel and Diesel in a Constant Volume Combustion Chamber

2011-04-12
2011-01-1380
This paper investigates the combustion of biodiesel and diesel in an optical accessible constant volume chamber that can simulate the conditions in compression ignition engines. The high-pressure and high-temperature environment in the chamber was generated by a controlled premixed combustion with desired content of oxygen left. A common rail and an injector with 160 degree included angle were used to deliver the fuel. Ultra low sulfur diesel (ULSD) and biodiesel from used cook oil were used in this paper. High speed imaging of natural luminosity from the flame was used to study the combustion flame in a time resolved manner. A combination of high speed and intensified imaging of OH chemiluminescence was employed to identify reaction zones. This method has the advantage of capturing the global pictures, thus allowing the studying of jet-to-jet variations, while it does not sacrifice the time-resolved resolution.
Journal Article

Experimental Investigation of Droplet Dynamics and Spray Atomization inside Thermostatic Expansion Valves

2011-04-12
2011-01-0129
In this paper, experimental investigation on spray atomization and droplet dynamics inside a thermostatic expansion valve (TXV), a component commonly used in vehicle refrigeration system, was conducted. A needle and an orifice were copied from a commercial TXV and machined to be mounted inside a chamber with optical access so that the flow inside the TXV is simulated and visualized at the same time. The break-up and atomization of the refrigerant were documented near the downstream of the orifice under different feed conditions for two TXV with different geometry. A Phase Doppler Anemometry (PDA) system was used later to measure the size and velocity of atomized refrigerant droplets. The results showed that the droplet size variation along the radial direction is slightly decreased at near downstream and increased at farther downstream due to the coalescence.
Technical Paper

Experimental Evaluation of Electrostatically Assisted Injection and Combustion of Ethanol-Gasoline Mixtures for Automotive Applications

2010-04-12
2010-01-0171
A single nozzle port fuel injector was modified to apply electrostatic charge to the fuel stream, with the intention of studying electrostatically assisted sprays in a practical, port-injected engine. The modifications were kept external to the injector and involved placing an electrode and insulating liner over the tip of the injector. The performance of the modified injector, which combined pressure driven and electrostatic atomization, was characterized in three phases: the injector sprays themselves were studied, combustion of charged fuel droplets was studied, and the injector was installed and tested on a single cylinder spark ignition engine. In the first phase, Fraunhofer diffraction measurements of droplet size, and particle image velocimetry measurements of droplet velocity were performed. The charge transferred by the sprays was measured using an electrometer, and typical forces exerted on droplets in the sprays were estimated.
Technical Paper

Effects of Injection Pressure on Low-sooting Combustion in an Optical HSDI Diesel Engine Using a Narrow Angle Injector

2010-04-12
2010-01-0339
An optically accessible single-cylinder high-speed direct-injection (HSDI) diesel engine equipped with a Bosch common rail injection system was used to study effects of injection pressures on the in-cylinder spray and combustion processes. An injector with an injection angle of 70 degrees and European low sulfur diesel fuel (cetane number 54) were used in the work. The operating load was 2.0 bar IMEP with no EGR added in the intake. The in-cylinder pressure was measured and the heat release rate was calculated. High-speed Mie-scattering technique was employed to visualize the liquid distribution and evolution. High-speed combustion video was also captured for all the studied cases using the same frame rate. NOx emissions were measured in the exhaust pipe. The experimental results indicated that for all of the conditions the heat release rate was dominated by a premixed combustion pattern. Two-stage low temperature reaction was seen for early injection timings.
Technical Paper

Cavitating Flow within an Injector-Like Geometry and the Subsequent Spray

2019-04-02
2019-01-0284
Cavitation plays a significant role in the spray characteristics and the subsequent mixing and combustion process in engines. Cavitation has beneficial effects on the development of the fuel sprays by improving injection velocity and promoting primary break-up. On the other hand, intense pressure peaks induced by the vapor collapse may lead to erosion damage and severe degradation of the injector performance. In the present paper, the transient cavitating flow in the injector-like geometry was investigated using the modified turbulence model and cavitation criterion. A local density correction was used in the Reynolds-averaged Navier-Stokes turbulence model to reduce the turbulent viscosity, which facilitates the cavitation development. The turbulent stress was also considered in the cavitation inception stage. The modified model is capable of reproducing the cavitating flow with an affordable computational cost.
Technical Paper

Macroscopic and Microscopic Characteristics of Flash Boiling Spray with Binary Fuel Mixtures

2019-04-02
2019-01-0274
Flash boiling has drawn much attention recently for its ability to enhance spray atomization and vaporization, while providing better fuel/air mixing for gasoline direct injection engines. However, the behaviors of flash boiling spray with multi-component fuels have not been fully discovered. In this study, isooctane, ethanol and the mixtures of the two with three blend ratios were chosen as the fuels. Measurements were performed with constant fuel temperature while ambient pressures were varied to adjust the superheated degree. Macroscopic and microscopic characteristics of flash boiling spray were investigated using Diffused Back-Illumination (DBI) imaging and Phase Doppler Anemometry (PDA). Comparisons between flash boiling sprays with single component and binary fuel mixtures were performed to study the effect of fuel properties on spray structure as well as atomization and vaporization processes.
Technical Paper

Spray Characteristics of Gasoline-Ethanol Fuel Blends under Flash-Boiling Conditions

2019-04-02
2019-01-0297
The spray structure and vaporization processes of flash-boiling sprays in a constant volume chamber under a wide range of superheated conditions were experimentally investigated by a high speed imaging technique. The Engine Combustion Network’s Spray G injector was used. Four fuels including gasoline, ethanol, and gasoline-ethanol blends E30 and E50 were investigated. Spray penetration length and spray width were correlated to the degree of the superheated degree, which is the ratio of the ambient pressure to saturated vapor pressure (pa/ps). It is found that parameter pa/ps is critical in describing the spray transformation under flash-boiling conditions. Three distinct stages namely the slight flash-boiling, the transition flash-boiling, and the flare flash-boiling are identified to describe the transformation of spray structures.
Technical Paper

An Experimental Study of the Combustion, Performance and Emission Characteristics of a CI Engine under Diesel-1-Butanol/CNG Dual Fuel Operation Mode

2016-04-05
2016-01-0788
In order to comply with the stringent emission regulations, many researchers have been focusing on diesel-compressed natural gas (CNG) dual fuel operation in compression ignition (CI) engines. The diesel-CNG dual fuel operation mode has the potential to reduce both the soot and NOx emissions; however, the thermal efficiency is generally lower than that of the pure diesel operation, especially under the low and medium load conditions. The current experimental work investigates the potential of using diesel-1-butanol blends as the pilot fuel to improve the engine performance and emissions. Fuel blends of B0 (pure diesel), B10 (90% diesel and 10% 1-butanol by volume) and B20 (80% diesel and 20% 1-butanol) with 70% CNG substitution were compared based on an equivalent input energy at an engine speed of 1200 RPM. The results indicated that the diesel-1-butanol pilot fuel can lead to a more homogeneous mixture due to the longer ignition delay.
Technical Paper

Numerical Study and Parameter Optimization on a Diesel - Natural Gas Dual Fuel Engine

2016-04-05
2016-01-0769
This work presents a comprehensive computational study of diesel - natural gas (NG) dual fuel engine. A complete computational model is developed for the operation of a diesel - NG dual fuel engine modified from an AVL 5402 single cylinder diesel test engine. The model is based on the KIVA-3V program and includes customized sub-models. The model is validated against test cell measurements of both pure diesel and dual fuel operation. The effects of NG on ignition and combustion in dual fuel operation are analyzed in detail. Zero-dimensional computations with a diesel surrogate reaction mechanism are conducted to discover the effects of NG on ignition and combustion and to reveal the fundamental chemical mechanisms behind such effects. Backed by the detailed theoretical analysis, the engine operation parameters are optimized with genetic algorithm (GA) for the dual fuel operation of the modified AVL 5402 test engine.
Technical Paper

Experimental Investigation and Analysis of Combustion Process in a Diesel Engine Fueled with Acetone-Butanol-Ethanol/ Diesel Blends

2016-04-05
2016-01-0737
The performance and emission of an AVL 5402 single-cylinder engine fueled with acetone-butanol-ethanol (ABE) / diesel blends were experimentally investigated at various load conditions and injection timings. The fuels tested in the experiments were ABE10 (10% ABE, 90% diesel), ABE20 and diesel as baseline. Thermodynamics analyses of pressure traces acquired in experiments were performed to show the impact of ABE concentration to the overall combustion characteristics of the fuel mixtures. Cumulative heat release analysis showed that ABE mixtures generally retarded the overall combustion phasing, ignition delays of ABE-containing fuels were significantly extended, however, combustion rate during CA10∼CA50 were accelerated at different extent. Pressure rise rate of ABE-containing fuels further implicated that the premixed combustion were more dominant than that of diesel. Polytropic indices of both expansion and compression strokes were calculated from p-V diagram.
Technical Paper

A Modeling Study of the Effects of Butanol Addition on Aromatic Species in Premixed Butane Flames

2016-04-05
2016-01-0574
The motivation of the present work was to understand the mechanism by which alcohols produce less aromatic species in their combustion process than an equal amount of hydrocarbon with similar molecular structure does. Due to its numerous advantages over short-chain alcohols, butanol has been considered very promising in soot reduction. Excluding the influence of spray, vaporization and mixing process in engine cases, an adiabatic constant-pressure reactor model was applied to investigate the effect of butanol additives on aromatic species, which are known to be soot precursors, in fuel-rich butane flames. To keep the carbon flux constant, 5% and 10% oxygen by mass of the fuel were added to butane using butanol additive, respectively. Based on the soot reduction effects proposed in literature, effects on temperature, key radical concentrations and the carbon removal from the pathway to aromatic species were considered to identify the major mechanism of reduction in aromatic species.
Technical Paper

NOx Reduction in Compression-Ignition Engine by Inverted Ignition Phi-Sensitivity

2017-03-28
2017-01-0749
A new approach of NOx reduction in the compression-ignition engine is introduced in this work. The previous research has shown that during the combustion stage, the high temperature ignition tends to occur early at the near-stoichiometric region where the combustion temperature is high and majority of NOx is formed; Therefore, it is desirable to burn the leaner region first and then the near-stoichiometric region, which inhibits the temperature rise of the near-stoichiometric region and consequently suppresses the formation of NOx. Such inverted ignition sequence requires mixture with inverted phi-sensitivity. Fuel selection is performed based on the criteria of strong ignition T-sensitivity, negligible negative temperature coefficient (NTC) behavior, and large heat of vaporization (HoV).
Technical Paper

High-Load Compression-Ignition Engine Emissions Reduction with Inverted Phi-Sensitivity Fuel Using Multiple Injection Strategies

2019-04-02
2019-01-0554
Inverted phi (ϕ)-sensitivity is a new approach of NOx reduction in compression-ignition (C.I.) engines. Previously, pure ethanol (E100) was selected as the preliminary test fuel in a single injection compression-ignition engine, and was shown to have good potential for low engine-out NOx emissions under low and medium load conditions due to its inverted ignition sequence. Under high load, however, the near-stoichiometric and non-homogeneous fuel/air distribution removes the effectiveness of the inverted ϕ-sensitivity. Therefore, it is desirable to recover the combustion sequence in the chamber such that the leaner region is burned before the near-stoichiometric region. When the combustion in near-stoichiometric region is inhibited, the temperature rise of that region is hindered and the formation of NOx is suppressed.
Technical Paper

Liquid and Vapor Fuel Distributions within a High Speed Direct Injection (HSDI) Diesel Engine Operating in HCCI and Conventional Combustion Modes

2005-10-24
2005-01-3838
An optically accessible single cylinder small-bore HSDI diesel engine equipped with a Bosch common-rail injection system was used to study the effects of multiple injection strategies on the in-cylinder combustion processes. The operating conditions were considered typical in the metal engine under moderate load conditions. In-cylinder pressure traces are used to analyze heat release characteristics. The combustion modes transit from the Homogeneous Charge Compression Ignition (HCCI)-like combustion mode to conventional diesel combustion by changing injection parameters. The whole cycle combustion process was visualized through a high-speed digital video camera and the combustion images clearly show the combustion mode transition. Laser-Induced Exciplex Fluorescence (LIEF) technique was used to obtain simultaneous liquid and vapor fuel distributions within the combustion chamber, with tetradecane-TMPD-naphthalene as the base fuel-dopant combination.
Technical Paper

Comparisons of Computed and Measured Results for a HSDI Diesel Engine Operating Under HCCI Mode

2006-04-03
2006-01-1519
As engine researchers are facing the task of designing more powerful, more fuel efficient and less polluting engines, a large amount of research has been focused towards homogeneous charge compression ignition (HCCI) operation for diesel engines. Ignition timing of HCCI operation is controlled by a number of factors including intake temperatures, exhaust gas recirculation (EGR) and injection timing to name a few. This study focuses on the computational modeling of an optically accessible high-speed direct-injection (HSDI) small bore diesel engine. In order to capture the phenomena of HCCI operation, the KIVA computational code package has been outfitted with an improved and optimized Shell autoignition model, the extended Zeldovich thermal NOx model, and soot formation and oxidation models. With the above named models in place, several cases were computed and compared to experimentally measured data and captured images of the DIATA test engine.
Technical Paper

Low Temperature Combustion within a Small Bore High Speed Direct Injection (HSDI) Diesel Engine

2005-04-11
2005-01-0919
Homogeneous Charge Compression Ignition (HCCI) combustion employing single main injection strategies in an optically accessible single cylinder small-bore High-Speed Direct Injection (HSDI) diesel engine equipped with a Bosch common-rail electronic fuel injection system was investigated in this work. In-cylinder pressure was taken to analyze the heat release process for different operating parameters. The whole cycle combustion process was visualized with a high-speed digital camera by imaging natural flame luminosity. The flame images taken from both the bottom of the optical piston and the side window were taken simultaneously using one camera to show three dimensional combustion events within the combustion chamber. The engine was operated under similar Top Dead Center (TDC) conditions to metal engines. Because the optical piston has a realistic geometry, the results presented are close to real metal engine operations.
Technical Paper

Smokeless Combustion within a Small-Bore HSDI Diesel Engine Using a Narrow Angle Injector

2007-04-16
2007-01-0203
Combustion processes employing different injection strategies in a High-Speed Direct Inject (HSDI) diesel engine were investigated using a narrow angle injector (70 degree). Whole-cycle combustion was visualized using a high-speed digital video camera. The liquid spray evolution process was imaged by the Mie-scattering technique. Different injection strategies were employed in this study including early pre-Top Dead Center (TDC) injection, post-TDC injection, multiple injection strategies with an early pre-TDC injection and a late post-TDC injection. Smokeless combustion was obtained under some operating conditions. Compared with the original injection angle (150 degree), some new combustion phenomena were observed for certain injection strategies. For early pre-TDC injection strategies, liquid fuel impingement is observed that results in some newly observed fuel film combustion flame (pool fires) following an HCCI-like weak flame.
Technical Paper

Reducing NOx Emissions from a Common-Rail Engine Fueled with Soybean Biodiesel

2011-04-12
2011-01-1195
Performance and emissions of a common-rail production diesel engine fueled with soybean-derived biodiesel was investigated. The work was broken down into two categories. First, adjustment of injection timing and EGR ratio was investigated as a means to reduce NOx emissions to levels comparable with those obtained when using pure diesel fuel. Next, simultaneous reduction of NOx and soot emissions was investigated using high rates of EGR combined with late injection timings to approach the low-temperature combustion regime. Results from the first part of the study indicate that optimization of engine control parameters for use with biodiesel can be beneficial to performance and emissions. It was found that adjusting the engine's MAF setpoint table to reflect the difference in stoichiometric air-fuel ratio between diesel and biodiesel brought NOx emissions to comparable or lower levels.
Technical Paper

A Study of Effects of Volatility on Butanol-Biodiesel-Diesel Spray and Combustion

2011-04-12
2011-01-1197
Ternary blends of butanol-biodiesel-diesel with different blending ratios were tested inside a constant volume chamber under various ambient temperatures so as to investigate the spray and combustion characteristics of the fuels. Applying the high speed imaging, a sudden drop in spray penetration was observed at ambient temperature of 800 K and 900 K for fuels with certain blending ratio, but not at 1000 K and 1200 K. When the spray penetration of the butanol-biodiesel-diesel blends was compared to that of the biodiesel-diesel blends under non-combusting environment, a sudden drop in spray penetration length was also observed at 1100 K. The results indicated that for the non-combusting case, the tip of the spray jet erupted into a plume sometime after injection for the butanol-biodiesel-diesel blend at an ambient temperature of 1100 K. Such phenomenon was not seen with the biodiesel-diesel blend, neither with the same fuel but at a lower ambient temperature of 900 K.
X