Refine Your Search

Topic

Search Results

Standard

Heavy Duty OBD IUMPR Data Collection Tool Process

2018-09-04
CURRENT
J3162_201809
This document describes the collection of IUMPR data required by the Heavy Duty On-Board Diagnostic regulation 13 CCR 1971.1 (l)(2.3.3), using SAE J1939-defined messages incorporated in a suite of software functions.
Standard

CAN FD Physical Layer, 500 kbps/2 Mbps

2017-06-15
WIP
J1939-17
This document defines a physical layer having a higher bandwidth capacity than the classic physical layers defined for SAE J1939-14 by using flexible data rates. CAN controllers are now available which support the Flexible Data Rate Frame Format as defined in ISO 11898-1:2015. These controllers and compatible high speed transceivers are required for use on SAE J1939-17 networks. This SAE Recommended Practice is intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
Standard

CAN FD Data Link Layer

2018-05-09
WIP
J1939-22
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-22, describes the data link layer using the Flexible Data Rate Extended Frame Format (FEFF) with 29-bit Identifiers, as defined in ISO 11898-1, December 2015. For SAE J1939 no alternative data link layers are permitted using FEFF messages.
Standard

SAE J1939 Network Security

2017-03-06
WIP
J1939-91
This document will provide recommendations to vehicle manufacturers and component suppliers in securing the SAE J1939-13 connector interface from the cybersecurity risks posed by the existence of this connector.
Standard

Agricultural and Forestry Off-Road Machinery Control and Communication Network

2006-08-23
HISTORICAL
J1939/2_200608
These RPs are intended for light and heavy duty vehicles used primarily off road as well as appropriate stationary applications which use vehicle derived components (e.g. generator sets). Vehicles of interest include, but are not limited to: construction equipment; and agricultural equipment and implements. The purpose of these RPs is to provide an open interconnect system for electronic systems. It is the intention of these recommended practices to allow Electronic Control Units to communicate with each other by providing a standard architecture. This document is intended to specify the requirements for application of J1939 in construction and agricultural equipment. This document specifies the series of documents within the set of J1939 documents that are applicable to construction and agricultural equipment and provides further requirements for this industry.
Standard

Agricultural and Forestry Off-Road Machinery Control and Communication Network

2013-03-11
HISTORICAL
J1939/2_201303
SAE J1939-02 Agricultural and Forestry Off-Road Machinery Network specifies the requirements for application of SAE J1939 in agricultural and forestry equipment. This document specifies the series of documents within the set of SAE J1939 documents that are applicable to agricultural and forestry equipment and provides further requirements for this industry. The SAE and ISO groups have cooperated to define agricultural and forestry networks in a manner to allow compatibility of ECUs and messaging protocols between the A&F and the T&B networks.
Standard

Agricultural and Forestry Off-Road Machinery Control and Communication Network

2019-01-14
CURRENT
J1939/2_201901
SAE J1939-2 specifies the requirements for application of SAE J1939 in agricultural and forestry equipment. This document specifies the series of documents within the set of SAE J1939 documents that are applicable to agricultural and forestry equipment and provides further requirements for this industry. The SAE and ISO groups have cooperated to define agricultural and forestry networks in a manner to allow compatibility of ECUs and messaging protocols between the A&F and the T&B networks.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2008-02-21
HISTORICAL
J1939/5_200802
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2017-10-13
CURRENT
J1939/5_201710
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2012-04-13
HISTORICAL
J1939/5_201204
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

OBD Traceability Matrix

2019-02-05
CURRENT
J1939-90_201902
This Information Report is intended to supplement the J1939 documents by offering the application of SAE RP J1939 to OBD data communications in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual regulations and standards documents, and any discrepancies between this document and the published documents must be resolved in favor of the published documents. This spreadsheet outlines elements in ARB OBD II and HD OBD requirements and identifies which J1939 SPNs and messages may be used to satisfy the datastream, readiness, in-use ratio, and test results requirements.
Standard

Digital Annex of Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

2014-11-04
HISTORICAL
J2403DA_201411
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
Standard

Digital Annex of Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

2014-02-07
HISTORICAL
J2403DA_201402
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
Standard

Digital Annex of Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

2016-02-18
HISTORICAL
J2403DA_201602
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
Standard

Digital Annex of Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

2018-07-16
CURRENT
J2403DA_201807
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
Standard

Digital Annex of Medium/Heavy-Duty E/E Systems Diagnosis Nomenclature

2017-03-30
HISTORICAL
J2403DA_201703
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
Standard

Application Layer - Generator Sets and Industrial

2002-12-19
HISTORICAL
J1939/75_200212
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g., Generator sets). Vehicles of interest include, but are not limited to: on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-75, describes the parameters and parameter groups that are predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications.
Standard

Application Layer - Generator Sets and Industrial

2006-07-10
HISTORICAL
J1939/75_200607
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g., Generator sets). Vehicles of interest include, but are not limited to: on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-75, describes the parameters and parameter groups that are predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications.
Standard

Application Layer - Generator Sets and Industrial

2007-06-21
HISTORICAL
J1939/75_200706
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g., Generator sets). Vehicles of interest include, but are not limited to: on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-75, describes the parameters and parameter groups that are predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications.
Standard

Application Layer—Generator Sets and Industrial

2011-05-16
HISTORICAL
J1939/75_201105
SAE J1939-75 Generator Sets and Industrial Applications defines the set of data parameters (SPNs) and messages (PGNs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. Applications using the SAE J1939-75 document may need to reference SAE J1939-71 for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g. engines and turbines, that power the generators and driven industrial equipment.
X