Search Results

This document covers the general terms and corresponding definitions that support the design, development, implementation, testing, and application of vehicle networks. The terminology also covers some terms and concepts of distributed embedded systems, network hardware, network software, physical layers, protocols, and other related areas.

This SAE Information Report provides definition for terms (words and phrases) which are generally used within the SAE in describing network and data communication issues. In many cases, these definitions are different from those of the same or similar terms found in nonautomotive organizations, such as the Institute of Electrical and Electronic Engineers (IEEE). The Vehicle Networks for Multiplexing and Data Communications committee has found it useful to collect these specific terms and definitions into this document so documents related to the multiplexing and data communications issues will not need an extensive definitions section. This document is intended to be the central reference for terms and definitions related to multiplexing and data communications and as such is intended to apply equally to Passenger Car, Truck and Bus, and Construction and Agriculture organizations within SAE.

This Glossary confines its content to the specific field of electronic systems and subsystems as they pertain to the automotive engineer.

This SAE Recommended Practice defines the information contained in the header and data fields of non-diagnostic messages for automotive serial communications based on SAE J1850 Class B networks. This document describes and specifies the header fields, data fields, field sizes, scaling, representations, and data positions used within messages. The general structure of a SAE J1850 message frame without in-frame response is shown in Figure 1. The structure of a SAE J1850 message with in-frame response is shown in Figure 2. Figures 1 and 2 also show the scope of frame fields defined by this document for non-diagnostic messages. Refer to SAE J1979 for specifications of emissions related diagnostic message header and data fields. Refer to SAE J2190 for the definition of other diagnostic data fields. The description of the network interface hardware, basic protocol definition, the electrical specifications, and the CRC byte are given in SAE J1850.

This SAE Information Report will explain the differences between Class A, B, and C networks and clarify through examples, the differences in applications. Special attention will be given to a listing of functions that could be attached to a Class A communications network.

This SAE Information Report will explain the differences between Class A, B, and C networks and clarify through examples, the differences in applications. Special attention will be given to a listing of functions that could be attached to a Class A communications network.

This document is an information report and intended to provide an overview of the Clock Extension Peripheral Interface (CXPI) protocol.

This document defines a level of standardization in the implementation of the digital pulse scheme for reporting sensor information via Single Edge Nibble Transmission (SENT) encoding. This standard will allow ECU and tool manufacturers to satisfy the needs of multiple end users with minimum modifications to the basic design. This standard will benefit vehicle Original Equipment Manufacturers (OEMs) by achieving lower ECU costs due to higher industry volumes of the basic design. Requirements stated in this document provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This assures data communication among all connected devices regardless of supplier. This document is a communication interface specification and no to be treated as product specification. The intended audience includes, but is not limited to, ECU suppliers, sensor suppliers, component release engineers and vehicle system engineers.

This document defines a level of standardization in the implementation of the digital pulse scheme for reporting sensor information via Single Edge Nibble Transmission (SENT) encoding. This standard will allow ECU and tool manufacturers to satisfy the needs of multiple end users with minimum modifications to the basic design. This standard will benefit vehicle Original Equipment Manufacturers (OEMs) by achieving lower ECU costs due to higher industry volumes of the basic design. Requirements stated in this document provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This assures data communication among all connected devices regardless of supplier. The intended audience includes, but is not limited to, ECU suppliers, sensor suppliers, component release engineers and vehicle system engineers.

This document defines a level of standardization in the implementation of the digital pulse scheme for reporting sensor information via Single Edge Nibble Transmission (SENT) encoding. This standard will allow ECU and tool manufacturers to satisfy the needs of multiple end users with minimum modifications to the basic design. This standard will benefit vehicle Original Equipment Manufacturers (OEMs) by achieving lower ECU costs due to higher industry volumes of the basic design. Requirements stated in this document provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This assures data communication among all connected devices regardless of supplier. The intended audience includes, but is not limited to, ECU suppliers, sensor suppliers, component release engineers and vehicle system engineers.

This document defines a level of standardization in the implementation of the digital pulse scheme for reporting sensor information via Single Edge Nibble Transmission (SENT) encoding. This standard will allow ECU and tool manufacturers to satisfy the needs of multiple end users with minimum modifications to the basic design. This standard will benefit vehicle Original Equipment Manufacturers (OEMs) by achieving lower ECU costs due to higher industry volumes of the basic design. Requirements stated in this document provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This assures data communication among all connected devices regardless of supplier. The intended audience includes, but is not limited to, ECU suppliers, sensor suppliers, component release engineers and vehicle system engineers.

This document defines a level of standardization in the implementation of the digital pulse scheme for reporting sensor information via Single Edge Nibble Transmission (SENT) encoding. This standard will allow ECU and tool manufacturers to satisfy the needs of multiple end users with minimum modifications to the basic design. This standard will benefit vehicle Original Equipment Manufacturers (OEMs) by achieving lower ECU costs due to higher industry volumes of the basic design. Requirements stated in this document provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This assures data communication among all connected devices regardless of supplier. This document is a communication interface specification and no to be treated as product specification. The intended audience includes, but is not limited to, ECU suppliers, sensor suppliers, component release engineers and vehicle system engineers.

This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On-and OffRoad Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.

This SAE Standard establishes the requirements for a Class B Data Communication Network Interlace applicable to all On- and Off-Road Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.

This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On- and Off-Road Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.

This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On- and Off-Road Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.

This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On-and OffRoad Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.

This SAE Recommended Practice establishes the requirements for a Class B Data Communication Network Interface applicable to all On and Off-Road Land Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps. Additionally, this document outlines one Physical Layer alternative to the two fully defined implementations that may allow the network to operate at a 125 Kbps data rate.

This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On- and Off-Road Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features).