Refine Your Search

Topic

Search Results

Journal Article

Exploring the Potential of Combustion on Titan

2018-04-07
Abstract Significant attention has been focused on Mars due to its relative proximity and possibility of sustaining human life. However, its lack of in-situ sources of energy presents a challenge to generate needed energy on the surface. Comparatively, Titan has a nearly endless source of fuel in its atmosphere and lakes, but both are lacking in regards to their oxidizing capacity. The finding of a possible underground liquid ammonia-water lake on Titan suggests that oxygen might actually be within reach. This effort provides the first theoretical study involving a primary energy generation system on Titan using the atmosphere as a fuel and underground water as the source for the oxygen via electrolysis from wind generated electricity.
Journal Article

Exploring Engine Oil Reactivity Effects on End Gas Knock in a Direct-Injection Spark Ignition Engine

2018-03-07
Abstract An experimental study was conducted in a direct-injection (DI) spark-ignited engine to determine the extent to which oil reactivity impacts combustion phasing and knock propensity. Three engine oils were examined: a baseline 20W30 oil from conventional base stock, a 5W30 oil from a synthetic base stock, and a jet oil from a hindered ester base stock. The engine was operated at a constant fueling rate of 24.7 mg/injection for two engine speed conditions (1500 and 2000 rpm) using two cam profile conditions (high and low lift), for a total of four operating conditions. Spark timing sweeps were conducted at each of the four operating conditions. Results were analyzed for an engine oil impact on combustion phasing, cycle-to-cycle variability, combustion duration, knock propensity, and knock intensity. No correlation between engine oil type and any of these performance metrics could be identified.
Journal Article

Investigations on Spark and Corona Ignition of Oxymethylene Ether-1 and Dimethyl Carbonate Blends with Gasoline by High-Speed Evaluation of OH* Chemiluminescence

2018-03-01
Abstract Bio-fuels of the 2nd generation constitute a key approach to tackle both Greenhouse Gas (GHG) and air quality challenges associated with combustion emissions of the transport sector. Since these fuels are obtained of residual materials of the agricultural industry, well-to-tank CO2 emissions can be significantly lowered by a closed-cycle of formation and absorption of CO2. Furthermore, studies of bio-fuels have shown reduced formation of particulate matter on account of the fuels’ high oxygen content therefore addressing air quality issues. However, due to the high oxygen content and other physical parameters these fuels are expected to exhibit different ignition behaviour. Moreover, the question is whether there is a positive superimposition of the fuels ignition behaviour with the benefits of an alternative ignition system, such as a corona ignition.
Journal Article

Soot Observations and Exhaust Soot Comparisons from Ethanol-Blended and Methanol-Blended Gasoline Combustion in a Direct-Injected Engine

2018-05-07
Abstract Particulate formation was studied under homogeneous-intent stoichiometric operating conditions when ethanol-blended (E10) or methanol-blended (M20) gasoline fuel was injected during intake stroke of a 4-stroke direct-injected engine. The engine was tested at wide open throttle under naturally aspirated conditions for a speed-load of 1500 rev/min and 9.8 bar indicated mean effective pressure. In-cylinder soot observations and exhaust soot measurements were completed for different fuel rail pressures, injection timings, coolant and piston temperatures of the optical engine. Fuel delivery settings were tested with both single and split injections during intake stroke. The target piston temperature of the optical engine was attained using pre-determined number of methane port fuel injection firing cycles. Overall, the in-cylinder soot observations correlated well with the engine-out soot measurements. A warmer cylinder head favored soot reduction for both fuels.
Journal Article

Uncertainty Assessment of Octane Index Framework for Stoichiometric Knock Limits of Co-Optima Gasoline Fuel Blends

2018-10-25
Abstract This study evaluates the applicability of the Octane Index (OI) framework under conventional spark ignition (SI) and “beyond Research Octane Number (RON)” conditions using nine fuels operated under stoichiometric, knock-limited conditions in a direct injection spark ignition (DISI) engine, supported by Monte Carlo-type simulations which interrogate the effects of measurement uncertainty. Of the nine tested fuels, three fuels are “Tier III” fuel blends, meaning that they are blends of molecules which have passed two levels of screening, and have been evaluated to be ready for tests in research engines. These molecules have been blended into a four-component gasoline surrogate at varying volume fractions in order to achieve a RON rating of 98. The molecules under consideration are isobutanol, 2-butanol, and diisobutylene (which is a mixture of two isomers of octene). The remaining six fuels were research-grade gasolines of varying formulations.
Journal Article

Carbon Monoxide Density Pattern Mapping from Recreational Boat Testing

2018-10-04
Abstract Exposure to carbon monoxide (CO) gas can cause health risks for users of recreational boats and watercraft. Activities such as waterskiing, wakeboarding, tubing, and wakesurfing primarily utilize gasoline engine-driven vessels which produce CO as a combustion by-product. Recent watersports trends show an increase in popularity of activities which take place closer to the stern of the boat (such as wakesurfing) as compared to traditional waterskiing and wakeboarding. Advancements in gas emissions treatment in marine engine exhaust system designs have reduced risks for CO exposure in some boats. This article presents results from on-water testing of three recreational boats, reports average and maximum values of CO levels under various conditions, and exhibits mapping of the density of CO relative to the stern of the test vessels.
Journal Article

Active Control of Cylinder Charge Motion Using Vortex Generating Jets (VGJs) on Generic Intake Port Geometries

2018-08-08
Abstract Swirl is known to have impact on the combustion process and the engine emission performance. Generally the swirl flows are generated on engines by e.g. helical or tangential intake ports. However, such features of intake ports constrict the airflow, resulting in raising pumping losses and thus higher fuel consumption. This article introduces a further possibility to generate and regulate the swirl flow by injecting air directly into the intake ports using Vortex Generating Jets (VGJs). The effect of air injection was studied by means of experimental investigations regarding swirl generation and flow rate improvement. The optimization of VGJ diameters, positions as well as injection airflow rate was carried out with respect to energy efficiency of swirl generation.
Journal Article

Transient Operation and Over-Dilution Mitigation for Low-Pressure EGR Systems in Spark-Ignition Engines

2018-09-17
Abstract Low-Pressure cooled Exhaust Gas Recirculation (LP-cEGR) is proven to be an effective technology for fuel efficiency improvement in turbocharged spark-ignition (SI) engines. Aiming to fully exploit the EGR benefits, new challenges are introduced that require more complex and robust control systems and strategies. One of the most important restrictions of LP-cEGR is the transient response, since long air-EGR flow paths introduce significant transport delays between the EGR valve and the cylinders. High dilution generally increases efficiency, but can lead to cycle-by-cycle combustion variation. Especially in SI engines, higher-than-requested EGR dilution may lead to combustion instabilities and misfires. Considering the long EGR evacuation period, one of the most challenging transient events is throttle tip-out, where the engine operation shifts from a high-load point with high dilution tolerance to a low-load point where EGR tolerance is significantly reduced.
Journal Article

Experimental Investigation of Ethanol-Diesel-Butanol Blends in a Compression Ignition Engine by Modifying the Operating Parameters

2018-10-31
Abstract The rapid utilization of fossil fuels has triggered the finding of alternative renewable fuel that replaces or reduces the consumption by alternative fuels for fueling compression ignition (CI) engines. One such renewable fuel is ethanol which can be manufactured from biomass. The present study details the utilization of an optimum amount of ethanol in CI engine by modifying the operating parameters. It was already published in the previous paper that 45% ethanol can be utilized along with diesel using 10% butanol as cosolvent. This fuel is also meeting the minimum requirement with respect to properties as per ASTM standards. This experimental study was performed to investigate the influence of modifying the engine operating parameters on the performance, combustion, and emission parameters fueled with the blend containing 45% ethanol under various load conditions.
Journal Article

Direct Versus Indirect Acting Piezoelectric CR Injectors: Comparison of Hydraulic Performance, Pollutant Emissions, Combustion Noise, and Fuel Consumption

2018-11-08
Abstract A comprehensive comparison between a direct acting and an indirect acting piezoelectric injector has been carried out both at the hydraulic rig and at the dynamometer cell. The working principle of these injector typologies is illustrated, and their hydraulic performance has been analyzed and discussed on the basis of experimental data collected at a hydraulic test rig. The injector characteristics, nozzle opening and closure delays, injector leakages, injected flow-rate profiles, injector-to-injector variability in the injected mass, injected volume fluctuations with the dwell time (DT), and minimum DT for fusion-free multiple injections have been compared in order to evaluate the impact of the injector driving system on the injection apparatus performance. The direct acting and indirect acting piezoelectric injectors have been installed on a Euro 5 diesel engine, which has been tested at a dynamometer cell.
Journal Article

LSPI Durability, a Study of LSPI over the Life of a Vehicle

2018-03-01
Abstract Increasingly stringent emissions standards and the related efforts to increase vehicle fuel economy have forced the development and implementation of many new technologies. In the light-duty, passenger vehicle segment, one key strategy has been downsized, down-sped, boosted engines. Gasoline direct injection, coupled with turbocharging, have allowed for a drastic reduction in engine size while maintaining or improving engine performance. However, obtaining more power from a smaller engine has produced some consequences. One major consequence is the uncontrolled combustion known as Low Speed Pre-Ignition (LSPI). LSPI and the high energy knocking event which frequently follows have been known to result in fractured pistons and catastrophic engine failure. The propensity at which LSPI occurs has been linked to engine oil formulation.
Journal Article

Lean Burn Combustion of Iso-Octane in a Rapid Compression Machine Using Dual Mode Turbulent Jet Ignition System

2018-03-23
Abstract Turbulent jet ignition (TJI) is a pre-chamber initiated combustion technology that has been demonstrated to provide low temperature, faster burn rate combustion of lean and intake charge diluted air-fuel mixtures. Dual mode turbulent jet ignition (DM-TJI) is a novel concept wherein a separate air supply is provided for the pre-chamber apart from the conventional auxiliary fuel as supplied for TJI systems. The current study aims to extend the lean flammability limit of a gasoline-fueled engine using DM-TJI. Ignition delay time and combustion behavior of ultra-lean iso-octane/air mixture (Lambda ≅ 3.0) was studied using a TJI-based optically accessible rapid compression machine. High-speed fuel spray recordings in the pre-chamber were obtained using borescope imaging setup. Images of the reacting turbulent jet and subsequent combustion in the main chamber were captured using a visible color camera.
Journal Article

Modelling of a Variable Displacement Lubricating Pump with Air Dissolution Dynamics

2018-04-18
Abstract The simulation of lubricating pumps for internal combustion engines has always represented a challenge due to the high aeration level of the working fluid. In fact, the delivery pressure ripple is highly influenced by the effective fluid bulk modulus, which is significantly reduced by the presence of separated air. This paper presents a detailed lumped parameter model of a variable displacement vane pump with a two-level pressure setting, in which the fluid model takes into account the dynamics of release and dissolution of the air in the oil. The pump was modelled in the LMS Imagine.Lab Amesim® environment through customized libraries for the evaluation of the main geometric features. The model was validated experimentally in terms of pressure oscillations in conditions of low and high aeration. The fraction of separated air in the reservoir of the test rig was measured by means of an X-ray technique.
Journal Article

Experimental Investigation of the Influence of Engine Operating Parameters on a Rankine Based Waste Heat Recovery System in a SI Engine

2018-04-18
Abstract One of the most promising techniques to reduce carbon dioxide (CO2) emissions of future combustion engines is the use of waste heat from exhaust gas with a Rankine cycle. The target of this study was to investigate the influence of engine operating parameters such as ignition timing, coolant temperature and injection parameters on the efficiency and performance of Rankine based waste heat recovery systems (WHR). This was done to gain basic knowledge about the influences of the engine operating parameters which helps to explain the system behavior under different operating conditions and second to identify the operating parameters with the highest overall system efficiency which can be used to highlight the impact of changes in engine application on the car. These first of a kind tests were performed on a state-of-the-art gasoline engine equipped with a prototype Rankine-system.
Journal Article

Complete Engine Thermal Model, a Comprehensive Approach

2018-04-18
Abstract Upcoming engine generations are characterized by both a general trend of increased specific-power and higher efficiency. This leads to increased thermal loads, compromising reliability, and simultaneously to a limited amount of heat under ordinary engine use. Heat is a valuable resource in providing passenger comfort and emission control. For these reasons the subject of engine thermal management is receiving increasing attention. This work presents a comprehensive study of the complete engine thermal behavior at relevant running conditions: rated-power, peak-torque and ordinary use. The work is further extended to the engine warm-up period. The result is a high-resolution complete engine thermal model, capable of simultaneously reporting the local temperature of any engine part, and the global engine heat balance at any engine load.
Journal Article

Influence of Miller Cycles on Engine Air Flow

2018-04-18
Abstract The influence of the intake valve lift of two Miller cycles on the in-cylinder flow field inside a DISI engine is studied experimentally since changes of the engine flow field directly affect the turbulent mixing and the combustion process. For the analysis of the impact of the valve timing on the general flow field topology and on the large-scale flow structures, high-speed stereo-scopic particle-image velocimetry measurements are conducted in the tumble plane and the cross-tumble plane. The direct comparison to a standard Otto intake valve lift curve reveals evidently different impacts on the flow field for both Miller cam shafts. A Miller cycle that features late intake valve closing shows a flow field comparable to the standard Otto valve timing and a tumble vortex of strong intensity can be identified.
Journal Article

Internal Combustion Engine Cylinder Volume Trace Deviation

2018-04-18
Abstract Heat release analysis is a widely used cylinder pressure-based method for evaluating combustion in engine development, and it is also being investigated as a means to control engine combustion. Heat release analysis has been shown to be sensitive to errors in the calculated cylinder volume, but despite this one of the most common assumptions is that the cylinder volume is nominal and can be calculated solely by the geometrical relations among the measures of the engine components. During engine operation, the components surrounding the combustion chamber are exposed to thermal forces, pressure forces, and mass forces from the reciprocating components. Due to these forces, the components will deform and the volume of the combustion chamber will deviate from its ideal volume. The volume will also be affected by the production tolerances of the engine.
Journal Article

Partial Transparency of Advanced Compression Ignition Combustion Chamber Deposits, Its Impact on Combustion Chamber Wall Temperatures and Application to Thermal Barrier Coating Design

2018-04-18
Abstract The proven impact of combustion chamber deposits, CCD, on advanced compression ignition, ACI, combustion strategies has spurred researchers to develop thermal barrier coatings, TBC, which can mimic CCD benefits on combustion efficiency and operational range expansion. However, application of TBCs within multi-mode engines exposes them to non-negligible soot radiation. In the present paper, the impact of radiation heat transfer on combustion chamber deposits is studied. The morphological construction of the combustion chamber deposit layer is shown to be partially transparent to radiation heat transfer, drawing corollaries with ceramic-based TBCs. Additional experimentation eliminates the optical transparency of CCD to reveal an “effective radiation penetration depth” facilitated by open surface porosity. The effective radiation penetration depth is then utilized to establish the relative communicating porosity of CCD and a magnesium zirconate TBC.
Journal Article

The Effect of Inlet Valve Timing and Engine Speed on Dual Fuel NG-Diesel Combustion in a Large Bore Engine

2018-04-18
Abstract High load (18 bar IMEP) dual fuel combustion of a premixed natural gas/air charge ignited by directly injected diesel fuel was studied in a large bore gas engine. A nozzle design with low flow rate was installed to inject a small diesel volume (10.4 mm3) equal an energetic amount of about two percent. The effect of compression end temperature on ignition and combustion was investigated using valve timings with early IVC (Miller) and maximum charging efficiency (MaxCC). Furthermore, the engine speed was reduced (1500 rpm to 1000 rpm) for the Miller valve timing to analyze the impact of the chemical time scale on the combustion process. During all experiments, the cylinder charge density was kept constant adjusting the intake pressure and the resulting air mass flow.
Journal Article

Elasto-Hydrodynamic Bearing Model in Powertrain Multi-Body Simulation

2018-04-18
Abstract Multi-body simulation is a well-established simulation technique in the analysis of internal combustion engines dynamics. The enhancement of multi-body simulation especially regarding flexible structures included effects of structural dynamics in the analysis and helped not only to broaden the field of application but also improved quality of the results. In connection to that there is a steady increase in the need for enhanced and refined modeling approaches for technical subsystems such as journal bearings. The paper on hand will present the elasto-hydrodynamic journal bearing module for the software FEV Virtual Engine which is a vertical application to the generic multi-body simulation suite Adams.
X