Refine Your Search

Topic

Search Results

Journal Article

Extending the Magic Formula Tire Model for Large Inflation Pressure Changes by Using Measurement Data from a Corner Module Test Rig

2018-03-05
Abstract Since the tire inflation pressure has a significant influence on safety, comfort and environmental behavior of a vehicle, the choice of the optimal inflation pressure is always a conflict of aims. The development of a highly dynamic Tire Pressure Control System (TPCS) can reduce the conflict of minimal rolling resistance and maximal traction. To study the influence of the tire inflation pressure on longitudinal tire characteristics under laboratory conditions, an experimental sensitivity analysis is performed using a multivalent usable Corner Module Test Rig (CMTR) developed by the Automotive Engineering Group at Technische Universität Ilmenau. The test rig is designed to analyze suspension system and tire characteristics on a roller of the recently installed 4 chassis roller dynamometer. Camber angle, toe angle and wheel load can be adjusted continuously. In addition, it is possible to control the temperature of the test environment between −20 °C and +45 °C.
Journal Article

Experimental Investigation of the Near Wall Flow Downstream of a Passenger Car Wheel Arch

2018-03-01
Abstract The flow around and downstream of the front wheels of passenger cars is highly complex and characterized by flow structure interactions between the external flow, fluid exiting through the wheelhouse, flow from the engine bay and the underbody. In the present paper the near wall flow downstream of the front wheel house is analyzed, combining two traditional methods. A tuft visualization method is used to obtain the limiting streamline pattern and information about the near wall flow direction. Additionally, time resolved surface pressure measurements are used to study the pressure distribution and the standard deviation. The propagation of the occurring flow structures is investigated by cross correlations of the pressure signal and a spectral analysis provides the characteristic frequencies of the investigated flow.
Journal Article

Performance Margin for Geometric Road Design

2018-08-08
Abstract Although several methods exist for measuring the performance capability of a vehicle, many require detailed knowledge of the forces acting at each tire contact patch or do not account for both the vehicle dynamics and the road geometry. A simple vehicle model is proposed to estimate the upper limit of performance capability for a given operating condition (the Performance Envelope) based on the Effective Friction and the road geometry (slope and cross-slope). The Effective Friction accounts for both the vehicle dynamics and road surface properties and is estimated, through simulation or experimentation, using two standard vehicle dynamics tests: constant radius cornering and straight-line braking. The Performance Margin is defined as the additional performance capability available before the vehicle reaches the Performance Envelope, both represented in the intuitive units of gravity.
Journal Article

Force Transmission Characteristics for a Loaded Structural-Acoustic Tire Model

2018-10-23
Abstract Concerns about tire noise radiation arise partly from city traffic planning, environmental protection, and pedestrian safety standpoints, while from the vehicle passengers’ perspective, noise transmitted to the vehicle interior is more important. It is the latter concern that is addressed in this article. Sound-absorbing materials generally offer good absorption at higher frequencies, but the reduction of relatively low frequency, structure-borne tire noise is a continuing focus of many auto manufacturers. A tire’s internal, acoustic cavity resonance is a very strong contributing factor to tire-related structure-borne noise, and it can easily be perceived by passengers. Some reduction of vehicle cabin noise can be achieved through the insertion of sound-absorbing material in the tires. However, apart from the additional cost for such tires, there is also an increased complexity when repairing them because of the need to avoid damaging the sound-absorptive lining.
Journal Article

Vehicle Stability Control through Optimized Coordination of Active Rear Steering and Differential Driving/Braking

2018-07-05
Abstract In this article, a hierarchical coordinated control algorithm for integrating active rear steering and driving/braking force distribution (ARS+D/BFD) was presented. The upper-level control was synthesized to generate the required rear steering angle and external yaw moment by using a sliding-mode controller. In the lower-level controller, a control allocation algorithm considering driving/braking actuators and tire forces constraints was designed to assign the desired yaw moment to the four wheels. To this end, an optimization problem including several equality and inequality constraints were defined and solved analytically. Finally, computer simulation results suggest that the proposed hierarchical control scheme was able to help to achieve substantial enhancements in handling performance and stability.
Journal Article

Introducing the Modified Tire Power Loss and Resistant Force Regarding Longitudinal Slip

2018-04-18
Abstract Investigation of vehicle resistant forces and power losses is of crucial importance owing to current state of energy consumption in transport sector. Meanwhile, considerable portion of resistant forces in a ground vehicle is traced back to tires. Pneumatic tires are known to be a source of energy dissipation as a consequence of their viscoelastic nature. The current study aims to provide a modification to tire resistance by considering the power loss in a tire due to longitudinal slip. The modified tire resistance is comprised of rolling resistance and a newly introduced resistance caused by tire slip, called slip resistance. The physical model is chosen for parameters sensitivity study since the tractive force is described in this model via tangible physical parameters, e.g. tire tangential stiffness, coefficient of friction, and contact patch length.
Journal Article

Robust Design for Steering Mechanism Based on Preference Function

2018-03-01
Abstract In order to improve robustness of vehicle dynamic performance, a steering mechanism model is proposed with alignment parameters of front wheel based on preference function method. In the steering mechanism model controllable variables include the trapezoid connection length, the base angle of steering trapezoid, the kingpin inclination angle, caster, camber and uncontrollable variables include load and initial braking velocity. Optimization objective is some vehicle dynamic performance. In the preference function method the individual performance preference and preference aggregation in designing variable space and performance variable space are analyzed. The individual performance preference includes the controllable variable preference, noise factor preference and optimization objective preference. The aggregation function is developed by aggregating all the individual performance preferences.
Journal Article

Development of Safe and Sustainable EPAS (Electric Power Assist Steering) System for Emerging Markets

2018-04-07
Abstract The vehicle attributes developed for emerging markets like India are unique because of different topographical conditions, diversity and culture within the different states. Major attributes in vehicle development process is development of safe and sustainable vehicle systems (steering, brakes etc.) for the driver. India is presently an emerging market for automotive sector. With booming economy, purchasing power of the consumer has gone up in the past few years. Most of young population of India have started buying the cars. At the same time, India’s road infrastructure, vehicle regulations have exalted over the years. The consumer cognizance towards the vehicles have started changing now. They want safer, robust system in their vehicles with new convenience features at affordable cost. In recent years, almost all OEM’s in India have migrated steering systems from HPAS to EPAS for payback on fuel economy and weight.
Journal Article

Design, Analysis, Simulation and Validation of Automobile Suspension System Using Drive-Shaft as a Suspension Link

2018-04-18
Abstract With increasing demands for higher performance along with lower vehicle emissions, lightweight vehicle system construction is key to meet such demands. Suspension and transmission assemblies being the key areas for weight-reduction, we have designed a revolutionary new type of suspension system which combines the suspension links with the powertrain assembly and thus completely eliminates one suspension member. Less weight means lower fuel-consumption with improved passenger-comfort and road-holding due to reduction in unsprung mass. Elimination of a suspension link reduces the overall cost of material, machining & fabrication making our design cost-effective than existing setups. This paper deals with the design and implementation of of our concept. A working prototype is also constructed and tested which completely validates our design.
Journal Article

A Predictive Tool to Evaluate Braking System Performance Using Thermo-Structural Finite Element Model

2019-10-14
Abstract The braking phenomenon is an aspect of vehicle stopping performance where with kinetic energy due to the speed of the vehicle is transformed into thermal energy produced by the brake disc and its pads. The heat must then be dissipated into the surrounding structure and into the airflow around the brake system. The thermal friction field during the braking phase between the disc and the brake pads can lead to excessive temperatures. In our work, we presented numerical modeling using ANSYS software adapted in the finite element method (FEM), to follow the evolution of the global temperatures for the two types of brake discs, full and ventilated disc during braking scenario. Also, numerical simulation of the transient thermal analysis and the static structural analysis were performed here sequentially, with coupled thermo-structural method.
Journal Article

Study of a Mono-Tube Hydraulic Energy Harvesting Shock Absorber

2019-09-23
Abstract In this chapter, a mono-tube hydraulic energy harvesting shock absorber is proposed. The absorber is featured with the autogeneration where it permits harvesting waste energy with a proper asymmetric ratio of compression/extension damping force can be obtained. Using the continuity equation and including the compressibility of the oil, equations that describe the variation of the oil pressure in model chambers are derived. Then, relations that relate chambers’ pressure with the damping force, the harvested power, and the system efficiency are derived. Results illustrate the effects of frequency, amplitude, external resistance, and chambers’ size on the damping force and the harvested power. The proposed model can harvest an average power of 500 W with maximum peak of 1800 W using an external resistance of 10 Ω at an input amplitude of 50 mm and frequency of 1.67 Hz.
Journal Article

Multi-Chamber Tire Concept for Low Rolling-Resistance

2019-04-08
Abstract Rolling-resistance is leading the direction of numerous tire developments due to its significant effect on fuel consumption and CO2 emissions considering the vehicles in use globally. Many attempts were made to reduce rolling-resistance in vehicles, but with no or limited success due to tire complexity and trade-offs. This article investigates the concept of multiple chambers inside the tire as a potential alternative solution for reducing rolling-resistance. To accomplish that, novel multi-chamber designs were introduced and numerically simulated through finite-element (FE) modeling. The FE models were compared against a standard design as the baseline. The influences on rolling-resistance, grip, cornering, and mechanical comfort were studied. The multi-chambers tire model reduced rolling-resistance considerably with acceptable trade-offs. Independent air volumes isolating tread from sidewalls would maintain tire’s profile effectively.
Journal Article

A Combination of Intelligent Tire and Vehicle Dynamic Based Algorithm to Estimate the Tire-Road Friction

2019-04-08
Abstract One of the most important factors affecting the performance of vehicle active chassis control systems is the tire-road friction coefficient. Accurate estimation of the friction coefficient can lead to better performance of these controllers. In this study, a new three-step friction estimation algorithm, based on intelligent tire concept, is proposed, which is a combination of experiment-based and vehicle dynamic based approaches. In the first step of the proposed algorithm, the normal load is estimated using a trained Artificial Neural Network (ANN). The network was trained using the experimental data collected using a portable tire testing trailer. In the second step of the algorithm, the tire forces and the wheel longitudinal velocity are estimated through a two-step Kalman filter. Then, in the last step, using the estimated tire normal load and longitudinal and lateral forces, the friction coefficient can be estimated.
Journal Article

A Probabilistic Approach to Hydroplaning Potential and Risk

2019-01-30
Abstract A major contributor to fatal vehicle crashes is hydroplaning, which has traditionally been reported at a specific vehicle speed for a given operating condition. However, hydroplaning is a complex phenomenon requiring a holistic, probabilistic, and multidisciplinary approach. The objective of this article is to develop a probabilistic approach to predict Hydroplaning Potential and Risk that integrates fundamental understanding of the interdependent factors: hydrology, fluid-solid interactions, tire mechanics, and vehicle dynamics. A novel theoretical treatment of Hydroplaning Potential and Risk is developed, and simulation results for the prediction of water film thickness and Hydroplaning Potential are presented. The results show the advantages of the current approach which could enable the improvement of road, vehicle, and tire design, resulting in greater safety of the traveling public.
Journal Article

Enhanced Coil Spring Modeling in Passenger Car Suspension for Improved Target Setting Process

2018-12-14
Abstract The problem addressed in this work is how to formulate accurate targets for coil springs in passenger car suspensions to ensure that the required ride height and wheel rate are achieved. The issue arises because suspensions often tend to introduce significant spring deformations other than a purely axial compression. Although these effects are quite common, their influence on suspension performance is still not well understood. To this purpose, a new enhanced spring model is presented. The theory behind the model is explained and the relationship between spring and suspension performance discussed in detail. To validate formulations, a series of numerical simulations has been carried out demonstrating the model accuracy. Finally, a novel approach to spring target setting is proposed based on this advanced spring model.
Journal Article

Improving Vehicle Rollover Resistance Using Fuzzy PID Controller of Active Anti-Roll Bar System

2018-12-20
Abstract The active anti-roll bar (AARB) system in vehicles has recently become one of the research hotspots in the field of vehicle technology to improve the vehicle’s active safety. In most off-road vehicles, high ground clearance is required while keeping all wheels in contact with the ground in order to improve traction and maintain load distribution among the wheels. A problem however arises in some types of the off-road vehicles when the vehicle is operated at high speeds on smooth roads. In such condition, the combination of the vehicle’s center of gravity position, large suspension stroke, and soft spring construction creates a stability problem, which could make the vehicle liable to rollover. This article analyzes a comparison of stability performance between passive and active anti-roll bar systems to improve rolling resistance. For active systems, two control strategies will be investigated. The conventional PID controller is firstly investigated and taken as a reference.
Journal Article

PSO-Fuzzy Gain Scheduling of PID Controllers for a Nonlinear Half-Vehicle Suspension System

2018-11-19
Abstract The present article addresses the gain scheduling of proportional-integral-differential (PID) controllers using fuzzy set theory coupled with a metaheuristic optimization technique to control the vehicle nonlinear suspension system. The nonlinearities of the vehicle suspension system are due to the asymmetric piecewise dampers, quadratic tire stiffness, and the cubical spring stiffness. Conventional PID controller suffers from the low performance subject to modeling nonlinearities, while fuzzy logic controller (FLC), as a universal approximator, has the capacity to deal with the nonlinear, stochastic, and complex models. However, finding the optimal Mamdani FLC rules is still a challenging task in addition to a proper architecture of the membership functions (MFs). As a remedy to this drawback, particle swarm optimization (PSO) technique is employed in this article to improve the efficiency of the FLC-based PID controllers.
Journal Article

Parasitic Battery Drain Problems and AUTOSAR Acceptance Testing

2018-04-18
Abstract Battery Drain problems can occur in the vehicle due to improper network management between electronic control units (ECUs). Aim of this paper is to identify the factors that cause transmission and cease of transmission of a network management message of an ECU along with its application messages that controls the sleep/wake-up performance of other ECUs in the network. Strategy used here is, based on the root cause analysis of problems found in Display unit in vehicle environment, the functional CAN signals impacting sleep/wake-up behavior is re-mapped along with the state flow transition of AUTOSAR NM Algorithm. A re-defined test case design and simulation for vehicle model is created. Especially it focuses on validating the impact of functional CAN signals on DUT’s sleep/wake-up performance.
Journal Article

An Adaptive Neuro-Fuzzy Inference System (ANFIS) Based Model for the Temperature Prediction of Lithium-Ion Power Batteries

2018-08-14
Abstract Li-ion batteries have been widely applied in the areas of personal electronic devices, stationary energy storage system and electric vehicles due to their high energy/power density, low self-discharge rate and long cycle life etc. For the better designs of both the battery cells and their thermal management systems, various numerical approaches have been proposed to investigate the thermal performance of power batteries. Without the requirement of detailed physical and thermal parameters of batteries, this article proposed a data-driven model using the adaptive neuro-fuzzy inference system (ANFIS) to predict the battery temperature with the inputs of ambient temperature, current and state of charge. Thermal response of a Li-ion battery module was experimentally evaluated under various conditions (i.e. ambient temperature of 0, 5, 10, 15 and 20 °C, and current rate of C/2, 1C and 2C) to acquire the necessary data sets for model development and validation.
Journal Article

Experimental Study on the Internal Resistance and Heat Generation Characteristics of Lithium Ion Power Battery with NCM/C Material System

2018-04-18
Abstract Heat generation characteristics of lithium ion batteries are vital for both the optimization of the battery cells and thermal management system design of battery packs. Compared with other factors, internal resistance has great influence on the thermal behavior of Li-ion batteries. Focus on a 3 Ah pouch type battery cell with the NCM/C material system, this paper quantitatively evaluates the battery heat generation behavior using an Extended Volume-Accelerating Rate Calorimeter in combination with a battery cycler. Also, internal resistances of the battery cell are measured using both the hybrid pulse power characteristic (HPPC) and electro-chemical impedance spectroscopy (EIS) methods. Experimental results show that the overall internal resistance obtained by the EIS method is close to the ohmic resistance measured by the HPPC method. Heat generation power of the battery cell is small during discharge processes lower than 0.5 C-rate.
X