Refine Your Search

Topic

Search Results

Viewing 1 to 20 of 20
Journal Article

Investigations on Spark and Corona Ignition of Oxymethylene Ether-1 and Dimethyl Carbonate Blends with Gasoline by High-Speed Evaluation of OH* Chemiluminescence

2018-03-01
Abstract Bio-fuels of the 2nd generation constitute a key approach to tackle both Greenhouse Gas (GHG) and air quality challenges associated with combustion emissions of the transport sector. Since these fuels are obtained of residual materials of the agricultural industry, well-to-tank CO2 emissions can be significantly lowered by a closed-cycle of formation and absorption of CO2. Furthermore, studies of bio-fuels have shown reduced formation of particulate matter on account of the fuels’ high oxygen content therefore addressing air quality issues. However, due to the high oxygen content and other physical parameters these fuels are expected to exhibit different ignition behaviour. Moreover, the question is whether there is a positive superimposition of the fuels ignition behaviour with the benefits of an alternative ignition system, such as a corona ignition.
Journal Article

Soot Observations and Exhaust Soot Comparisons from Ethanol-Blended and Methanol-Blended Gasoline Combustion in a Direct-Injected Engine

2018-05-07
Abstract Particulate formation was studied under homogeneous-intent stoichiometric operating conditions when ethanol-blended (E10) or methanol-blended (M20) gasoline fuel was injected during intake stroke of a 4-stroke direct-injected engine. The engine was tested at wide open throttle under naturally aspirated conditions for a speed-load of 1500 rev/min and 9.8 bar indicated mean effective pressure. In-cylinder soot observations and exhaust soot measurements were completed for different fuel rail pressures, injection timings, coolant and piston temperatures of the optical engine. Fuel delivery settings were tested with both single and split injections during intake stroke. The target piston temperature of the optical engine was attained using pre-determined number of methane port fuel injection firing cycles. Overall, the in-cylinder soot observations correlated well with the engine-out soot measurements. A warmer cylinder head favored soot reduction for both fuels.
Journal Article

Corrosion Behavior of Automotive Materials with Biodiesel: A Different Approach

2018-05-07
Abstract The issue of material compatibility of biodiesel has been discussed by few researchers but the reported corrosion rates were alarmingly high. This study addresses the corrosion issue of biodiesel with automotive materials with a different but systematic approach following SAE J1747 standard. In earlier studies while conducting material compatibility studies with biodiesel, mention of any specific standard/s has not been generally observed. Earlier studies were conducted by storing the samples for a long time without any change of fuel. However in actual automotive application, change of fuel is always on a periodic basis due to consumption of fuel and the SAE standard recommends for the same. This difference has a significant effect on the material compatibility as this periodic change does not result in making the fuel particularly biodiesel more acidic which is otherwise when stored for a long time during the test period.
Journal Article

Compatibility Assessment of Fuel System Thermoplastics with Bio-Blendstock Fuel Candidates Using Hansen Solubility Analysis

2018-03-01
Abstract The compatibility of key fuel system infrastructure plastics with 39 bio-blendstock fuel candidates was examined using Hansen solubility analysis. Fuel types included multiple alcohols, esters, ethers, ketones, alkenes and one alkane. These compounds were evaluated as neat molecules and as blends with the gasoline surrogate, dodecane and a mix of dodecane and 10% ethanol (E10D). The plastics included polyphenylene sulfide (PPS), polyethylene terephthalate (PET), polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), polyoxymethylene (POM), polybutylene terephthalate (PBT), polypropylene (PP), high density polyethylene (HDPE), along with several nylon grades. These materials have been rigorously studied with other fuel types, and their volume change results were found to correspond well with their predicted solubility levels.
Journal Article

The Impacts of Pd in BEA Zeolite on Decreasing Cold-Start NMOG Emission of an E85 Fuel Vehicle

2018-10-25
Abstract In the development of hydrocarbon (HC) traps for E85 fuel vehicle emission control, the addition of palladium (Pd) to BEA zeolite was studied for trapping and decreasing cold-start ethanol emissions. BEA zeolite after a laboratory aging at 750°C for 25 hours released nearly all of the trapped ethanol as unconverted ethanol at low temperature, and some ethene was released at a higher temperature by a dehydration reaction. The addition of Pd to BEA zeolite showed a decrease in the release of unconverted ethanol emissions even after the lab aging. The release of methane (CH4), acetaldehyde (CH3CHO), carbon monoxide (CO), and CO2 from Pd-BEA zeolite during desorption (temperature programmed desorption (TPD)) demonstrated that multiple ethanol reaction mechanisms were involved including dehydrogenation and decomposition reactions.
Journal Article

Limitations of Monoolein in Simulating Water-in-Fuel Characteristics of EN590 Diesel Containing Biodiesel in Water Separation Testing

2018-10-18
Abstract In modern diesel fuel a proportion of biodiesel is blended with petro-diesel to reduce environmental impacts. However, it can adversely affect the operation of nonwoven coalescing filter media when separating emulsified water from diesel fuel. This can be due to factors such as increasing water content in the fuel, a reduction in interfacial tension (IFT) between the water and diesel, the formation of more stable emulsions, and the generation of smaller water droplets. Standard water/diesel separation test methods such as SAE J1488 and ISO 16332 use monoolein, a universal surface-active agent, to simulate the effects of biodiesel on the fuel properties as part of water separation efficiency studies. However, the extent to which diesel/monoolein and diesel/biodiesel blends are comparable needs to be elucidated if the underlying mechanisms affecting coalescence of very small water droplets in diesel fuel with a low IFT are to be understood.
Journal Article

A Model Study for Prediction of Performance of Automotive Interior Coatings: Effect of Cross-Link Density and Film Thickness on Resistance to Solvents and Chemicals

2019-03-27
Abstract Automotive interior coatings for flexible and rigid substrates represent an important segment within automotive coating space. These coatings are used to protect plastic substrates from mechanical and chemical damage, in addition to providing colour and design aesthetics. These coatings are expected to resist aggressive chemicals, fluids, and stains while maintaining their long-term physical appearance and mechanical integrity. Designing such coatings, therefore, poses significant challenges to the formulators in effectively balancing these properties. Among many factors affecting coating properties, the cross-link density (XLD) and solubility parameter (δ) of coatings are the most predominant factors.
Journal Article

Interference between Tin Sulfides, Graphite and Novolak Oxidation

2017-03-07
Abstract Tin sulfides (SnS and SnS2), represent a safer and greener alternative to other metal sulfides such as copper sulfides, and MoS2 etc. Their behavior is usually associated to that of solid lubricants such as graphite. A mixture of tin sulfides, with the 65 wt% of SnS2, has been characterized by scanning electron microscopy and by thermal gravimetric analysis (TGA). In order to investigate the effect of tin sulfides upon two crucial friction material ingredients, two mixtures were prepared: the former was made by mixing tin sulfides with a natural flake graphite and the latter was made mixing tin sulfides with a straight novolak. They were analyzed by TGA and differential thermal analysis (DTA) in both nitrogen and air. Some interferences were detected between tin sulfides and graphite in air.
Journal Article

Vibration Response Properties in Frame Hanging Catalyst Muffler

2018-07-24
Abstract Dynamic stresses exist in parts of a catalyst muffler caused by the vibration of a moving vehicle, and it is important to clarify and predict the vibration response properties for preventing fatigue failures. Assuming a vibration isolating installation in the vehicle frame, the vibration transmissibility and local dynamic stress of the catalyst muffler were examined through a vibration machine. Based on the measured data and by systematically taking vibration theories into consideration, a new prediction method of the vibration modes and parameters was proposed that takes account of vibration isolating and damping. A lumped vibration model with the six-element and one mass point was set up, and the vibration response parameters were analyzed accurately from equations of motion. In the vibration test, resonance peaks from the hanging bracket, rubber bush, and muffler parts were confirmed in three excitation drives, and local stress peaks were coordinate with them as well.
Journal Article

Carbon Fiber/Epoxy Mold with Embedded Carbon Fiber Resistor Heater - Case Study

2018-04-07
Abstract The paper presents a complete description of the design and manufacturing of a Carbon Fiber/epoxy mold with an embedded Carbon Fiber resistor heater, and the mold performances in terms of its surface temperature distribution and thermal deformations resulting from the heating. The mold was designed for manufacturing aileron skins from Vacuum Bag Only prepreg cured at 135°C. The glass transition temperature of the used resin-hardener system was about 175°C. To ensure homogenous temperature of the mold working surface in the course of curing, the Carbon Fiber heater was embedded in a layer of a highly heat-conductive cristobalite/epoxy composite, forming the core of the mold shell. Because the cristobalite/epoxy composite displayed much higher thermal expansion than CF/epoxy did, thermal stresses could arise due to this discrepancy in the course of heating.
Journal Article

Modeling the Effect of Foam Density and Strain Rate on the Compressive Response of Polyurethane Foams

2018-05-08
Abstract Due to the high deformability and energy dissipation capacity of polymer foams in compression, they are used in automotive applications to mitigate mechanical impacts. The mechanical response of the foams is strongly affected by their density. Phenomenological relations have been proposed to describe the effect of foam density on their stress-strain response in compression at a fixed loading rate and the effect of loading rate at a fixed foam density. In the present work, these empirical approaches are combined allowing for the dependence of loading rate effect in compression on foam density. The minimum experimental data set for calibration of the proposed model consists of compression test results at two different loading rates of foams with two different densities.
Journal Article

Filled Rubber Isolator’s Constitutive Model and Application to Vehicle Multi-Body System Simulation: A Literature Review

2018-06-05
Abstract Rubber elements present highly nonlinear mechanical properties affected by frequency and amplitude of excitation, prestrain and temperature, etc. Finite element (FE) models and lumped parameter models can be distinguished in the development of constitutive models of rubbers. Based on the concept of overlay model, different kinds of viscoelastic, or frequency-dependent models, and elastoplastic/friction, or amplitude-dependent models, are compared in terms of their modelling approach, parameters identification process and applications. Prestrain-dependent models and temperature-dependent thermo-mechanical models are also reviewed, including some special models which are not based on the concept of the overlay model. Experimental and computational studies of cylindrical bushings subjected to coupled deformation modes are analyzed and discussed.
Journal Article

Experimental Investigation of Ethanol-Diesel-Butanol Blends in a Compression Ignition Engine by Modifying the Operating Parameters

2018-10-31
Abstract The rapid utilization of fossil fuels has triggered the finding of alternative renewable fuel that replaces or reduces the consumption by alternative fuels for fueling compression ignition (CI) engines. One such renewable fuel is ethanol which can be manufactured from biomass. The present study details the utilization of an optimum amount of ethanol in CI engine by modifying the operating parameters. It was already published in the previous paper that 45% ethanol can be utilized along with diesel using 10% butanol as cosolvent. This fuel is also meeting the minimum requirement with respect to properties as per ASTM standards. This experimental study was performed to investigate the influence of modifying the engine operating parameters on the performance, combustion, and emission parameters fueled with the blend containing 45% ethanol under various load conditions.
Journal Article

Experimental Study of Ignition Delay, Combustion, and NO Emission Characteristics of Hydrogenated Vegetable Oil

2019-02-01
Abstract In this article, a comparative study of hydrogenated vegetable oil (HVO) and Diesel was performed in two constant volume combustion rigs and an optical accessible compression-ignited chamber (OACIC). Ignition, combustion, and nitric oxide (NO) emissions were studied under constant ambient gas density of 16.4 kg/m3, 21% vol oxygen concentration, and two different injection pressures of 800 and 1000 bar. Emission of NO was measured only in the OACIC, while a line-of-sight soot temperature distribution by applying two-color pyrometry was investigated in both setups. In general, the HVO as alternative fuel showed shorter ignition delay and less NO emission than Diesel for both injection pressures. Due to difference in the molecular structure, soot temperature of biofuel flames had narrower temperature spectrum than conventional fuel. Moreover, this study reveals the significance of wall-jet interaction for utilization of the biofuel.
Journal Article

Rapid Methodology to Simultaneous Quantification of Differ Antioxidants in Biodiesel Using Infrared Spectrometry and Multivariate Calibration

2019-03-21
Abstract The aim of this work is to quantify three different antioxidants in biodiesel - Santoflex, baynox, and tocopherol-using Middle Infrared (MIR) spectroscopy and chemometrics. For the construction of the models, 28 samples containing an antioxidant in the range of 0.1 to 500 mg/kg in biodiesel were used. We developed three models based on PLS 1 multivariate calibration method to quantify each of the three antioxidants separately and a model based on PLS 2 method to quantify simultaneously all the antioxidants. All models were compared to the values of root mean square error of calibration (RMSEC) and validation (RMSEP). For the baynox, santoflex, and tocopherol antioxidants quantification using PLS 1, the values of RMSEC and RMSEP were 37.2, 18.8, 9.0 mg/kg, and 26.7, 21.1, 68.6 mg/kg, respectively.
Journal Article

Investigation into the Tribological Properties of Biodiesel-Diesel Fuel Blends Under the Run-In Period Conditions

2019-06-25
Abstract Lubricity is a very important issue for diesel fuel injectors and pumps (of an engine) that are lubricated by the fuel itself. Biodiesel as an alternative fuel has a number of technical advantages compared to conventional diesel. It is required to perform more research about the tribological behavior of biodiesel blends under run-in period conditions at different rotational speeds. Friction characteristics of biodiesel (mixture of sunflower and soybean methyl ester) were studied by using a four-ball wear testing machine. Results indicated that the friction was reduced with the increase in rotational speed under the run-in period conditions. Moreover, the results showed that the friction coefficient decreases at rotational speeds of 600 and 900 rpm as the proportion of biodiesel increases in the fuel blend.
Journal Article

Modelling and Numerical Simulation of Dual Fuel Lean Flames Using Local Burning Velocity and Critical Chemical Timescale

2019-07-02
Abstract Addition of hydrogen to hydrocarbons in premixed turbulent combustion is of technological interest due to their increased reactivity, flame stability and extended lean extinction limits. However, such flames are a challenge to reaction modelling, especially as the strong preferential diffusion effects modify the physical processes, which are of importance even for highly turbulent high-pressure conditions. In the present work, Reynolds-averaged Navier-Stokes (RANS) modelling is carried out to investigate pressure and hydrogen content on methane/hydrogen/air flames.
Journal Article

Performance, Fuel Economy, and Economic Assessment of a Combustion Concept Employing In-Cylinder Gasoline/Natural Gas Blending for Light-Duty Vehicle Applications

2019-04-25
Abstract In current production natural gas/gasoline bi-fuel vehicles, fuels are supplied via port fuel injection (PFI). Injecting a gaseous fuel in the intake port significantly reduces the volumetric efficiency and consequently torque as compared to gasoline. In addition to eliminating the volumetric efficiency challenge, direct injection (DI) of natural gas (NG) can enhance the in-cylinder flow, mixing, and combustion process resulting in improved efficiency and performance. A computational fluid dynamics (CFD) approach to model high-pressure gaseous injection was developed and validated against X-ray data from Argonne’s Advanced Photon Source. NG side and central DI of various designs and injection strategies were assessed experimentally along with CFD correlation. Significant effects on combustion metrics were quantified and explained via improved understanding of the in-cylinder flow effects due to NG injection.
Journal Article

Experimental Studies of the Effect of Ethanol Auxiliary Fuelled Turbulent Jet Ignition in an Optical Engine

2019-07-26
Abstract Internal combustion (IC) engines are widely used in automotive, marine, agricultural and industrial machineries because of their superior performance, high efficiency, power density, durability and versatility in size and power outputs. In response to the demand for improved engine efficiency and lower CO2 emissions, advanced combustion process control techniques and more renewable fuels should be adopted for IC engines. Lean-burn combustion is one of the technologies with the potential to improve thermal efficiencies due to reduced heat loss and higher ratio of the specific heats. In order to operate the IC engines with very lean air/fuel mixtures, multiple turbulent jet pre-chamber ignition has been researched and developed to extend the lean-burn limit. Turbulent Jet Ignition (TJI) offers very fast burn rates compared to spark plug ignition by producing multiple ignition sites that consume the main charge rapidly.
X