Refine Your Search

Topic

Author

Search Results

Standard

Vehicle Electromagnetic Immunity--On-Board Transmitter Simulation

2009-08-03
CURRENT
J551/12_200908
This part of SAE J551 specifies on-board transmitter simulation test methods and procedures for testing passenger cars and commercial vehicles. The electromagnetic disturbances considered in this part of SAE J551 are limited to continuous narrow band electromagnetic fields. SAE J551/1 specifies general, definitions, practical use, and basic principles of the test procedure.
Standard

R134a Refrigerant Charge Determination Test Method

2018-09-11
CURRENT
J3023_201809
The purpose of this document is to establish guidelines for determining the critical R134a refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a refrigerant charge for the HVAC system.
Standard

Heavy Duty OBD IUMPR Data Collection Tool Process

2018-09-04
CURRENT
J3162_201809
This document describes the collection of IUMPR data required by the Heavy Duty On-Board Diagnostic regulation 13 CCR 1971.1 (l)(2.3.3), using SAE J1939-defined messages incorporated in a suite of software functions.
Standard

Acceleration Factors

2014-09-12
CURRENT
SSB1_003A
This document is an annex to EIA Engineering Bulletin SSB-1, Guidelines for Using Plastic Encapsulated Microcircuits and Semiconductors in Military, Aerospace and Other Rugged Applications (the latest revision). This document provides reference information concerning acceleration factors commonly used by device manufacturers to model failure rates in conjunction with statistical reliability monitoring. These acceleration factors are frequently used by OEMs in conjunction with physics of failure reliability analysis to assess the suitability of plastic encapsulated microcircuits and semiconductors for specific end use applications.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2013-04-09
HISTORICAL
J2691_201304
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742 “Combination 11 Conductors and 4 Pairs ECBS Cable”. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2018-04-15
CURRENT
J2691_201804
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

Electromagnetic Testing by Eddy Current Methods

2018-01-09
CURRENT
J425_201801
The purpose of this SAE Information Report is to provide general information relative to the nature and use of eddy current techniques for nondestructive testing. The document is not intended to provide detailed technical information but to serve as an introduction to the principles and capabilities of eddy current testing, and as a guide to more extensive references listed in Section 2.
Standard

Electromagnetic Testing By Eddy Current Methods

1981-03-01
HISTORICAL
J425_198103
The purpose of this SAE Information Report is to provide general information relative to the nature and use of eddy current techniques for nondestructive testing. The document is not intended to provide detailed technical information but to serve as an introduction to the principles and capabilities of eddy current testing, and as a guide to more extensive references listed in Section 2.
Standard

Electromagnetic Testing By Eddy Current Methods

1976-04-01
HISTORICAL
J425B_197604
The purpose of this SAE Information Report is to provide general information relative to the nature and use of eddy current techniques for nondestructive testing. The document is not intended to provide detailed technical information but to serve as an introduction to the principles and capabilities of eddy current testing, and as a guide to more extensive references listed in Section 2.
Standard

Motorcycle Terminology

2016-10-26
WIP
J3133
The motorcycle terminology presented herein addresses two-wheel single track vehicles, as well as three wheel variants. . Although two-wheeled, single track scooters and mopeds are similar to traditional motorcycles, they have many characteristics which differentiate them from motorcycles, and while some terms will apply, this Terminology addresses motorcycles specifically, unless otherwise noted.
Standard

Electrical Wiring Systems for Construction, Agricultural, and Off-road Machines

1985-05-01
HISTORICAL
J821_198505
This SAE Recommended Practice applies to off-road, self-propelled work machines defined in SAE J1116 JUN81. Purpose This document is intended as a guide in establishing recommended material specifications and identification of the on-board electrical wiring systems for construction, agricultural, and off-road machines.
Standard

Voltage Regulators for Automotive-Type Generators

2006-01-09
CURRENT
J2669_200601
This SAE Definition Document contains historic voltage regulation methods and test requirements that have not been previously published. The purpose of this document is to recommend a set of definitions and practices for use on current and future 12 V vehicle electric power regulation and control systems in internal combustion engine road vehicles. This document is not intended to include nor exclude regulators used in higher voltage vehicle electrical systems. The term “generator” rather than “alternator” will be used even though these terms may be used interchangeably in practice.
Standard

Optical Imaging Evaluation of Impact Damage Resistance Testing on Exterior Finishes

2011-05-26
CURRENT
J2661_201105
This SAE Recommended Practice covers a procedure for evaluating plastic and multiple-layer coatings exposed to gravelometer testing (as defined in SAE J400) with an optical imaging and analysis system. The intent of the procedure is to detect, count and characterize instances of damage in the coated surface that fracture the top coat layer or penetrate through multiple layers of the coating system. It may be possible to extend this methodology of coating damage evaluation to specimens that have undergone test procedures or exposures that produce similar, discrete damage sites in the coating system. If so applied, evaluation results must be interpreted with respect to the limitations and intent implied by the original evaluation procedure and its associated rating system, if applicable.
Standard

Glossary of System Safety Engineering and Management

2018-05-08
WIP
SAE1003
This SAE Aerospace Information Report will be a compilation of system safety engineering and management terms and definitions covering concepts used across multiple products and disciplines
X