Refine Your Search

Date

Date

Topic

Topic

Hazardous materials Particulate filters Aerospace Exhaust emissions Power and Propulsion A-5A Wheels, Brakes and Skid Controls Committee Drivetrains Alloys Safety

Search Results

Viewing 1 to 20 of 65
123Next >Last >>
Sort by relevance
Standard

Test Method for Catalytic Carbon Brake Disk Oxidation
2013-12-04
WIP
AS6289
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This test is designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions.
Standard

Minimum Environmental Performance Standard for Parts 23, 25, 27, and 29 Aircraft Wheels Brakes, and Wheel and Brake Assemblies
2021-04-27
WIP
AS6961
This SAE Aerospace Standard (AS) prescribes the Minimum Performance Standards (MPS) for environmental conditions that wheel, brake, and wheel and brake assemblies to be used on aircraft certificated under 14 CFR Parts 23, 25, 27, and 29. The environmental requirements in this document shall be used in conjunction with other MPS defined in Technical Standard Orders for the applicable equipment.
Standard

Disposition of Damaged Wheels Involved in Accidents/Incidents
2020-09-17
CURRENT
ARP5600
This SAE Aerospace Recommended Practice (ARP) establishes a procedure for disposition of aircraft wheels that have been involved in accidents/incidents or have been exposed to overheat conditions or overload conditions from loss of adjacent tire pressure (paired wheels) or wheel tie bolts.
Standard

Information on Brake-By-Wire (BBW) Brake Control Systems
2013-04-22
HISTORICAL
AIR5372
A panel of the SAE A-5A Committee prepared this SAE Aerospace Information Report (AIR). The document describes the design approaches used for current applications of Brake-by-Wire (BBW) control systems that are used on commercial and military airplanes. The document also discusses the experience gained during service in the commercial and military environments, and covers system, ergonomic, hardware, and development aspects. The treatment includes the lessons that have been learned during application of the technology. Although there are a variety of approaches that have been used in the design of BBW systems, the main focus of this document is on systems that use the electro-hydraulic method of control. The overall range of implementations is briefly described in 2.3. Sections 3, 4, and 5 describe the electro-hydraulic method in detail.
Standard

Skid Control Equipment
2007-12-12
HISTORICAL
AS483B
This standard covers minimum requirements for skid control equipment for use on all types and models of civil aircraft. It shall be the responsibility of the applicant to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
Standard

SKID CONTROL EQUIPMENT
1975-01-15
HISTORICAL
AS483A
This standard covers minimum requirements for skid control equipment for use on all types and models of civil aircraft. It shall be the responsibility of the applicant to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
Standard

Aircraft Brake Temperature Monitoring
2021-10-28
CURRENT
ARP6812
This SAE Aerospace Recommended Practice (ARP) provides recommendations for the function, design, construction, and testing of an on-aircraft Brake Temperature Monitoring System (BTMS), sometimes referred to as a Brake Temperature Indication System (BTIS). NOTE: This ARP does not address: Cockpit ergonomics and Aircraft operating procedures. Various handheld methods of temperature sensing or readouts, as these are not associated with transport aircraft during normal operation. Temperature sensitive paints as a means to indicate exceedance of a landing gear axle temperature threshold due to brake temperature.
Standard

Assessment of Aircraft Wheel Sealing Systems
2020-09-17
CURRENT
ARP5146
This SAE Aerospace Recommended Practice (ARP) is intended to provide guidance on verifying the integrity of inflation pressure sealing systems of aircraft wheel/tire assemblies.
Standard

BRAKE DYNAMICS
2006-03-17
HISTORICAL
AIR1064C
The landing gear is a complex multi-degree of freedom dynamic system and may encounter vibration problems induced by braking action. The vibratory modes can be induced by several frictional characteristics and brake design features. These should be assessed during the design concept and verified during the development of the hardware. This SAE Aerospace Information Report (AIR) has been prepared by a panel of the A-5A Subcommittee to present an overview of the landing gear system problems associated with aircraft brake dynamics and the approaches to the solution of these problems. In addition, facilities available for test and evaluation are presented and discussed.1
Standard

SKID CONTROL SYSTEM VIBRATION SURVEY
2008-06-16
HISTORICAL
AIR764C
This technical report documents three surveys to determine realistic vibration requirements for skid control systems specifications and obtain updated vibration information for locations in aircraft where skid control system components are mounted.
Standard

USAF Aircraft Wheels
2012-05-09
HISTORICAL
AIR4012B
This SAE Aerospace Information Report (AIR) documents general technical data associated with many of the wheels used in the Air Force.
Standard

USAF Aircraft Wheels
2012-07-19
CURRENT
AIR4012C
This SAE Aerospace Information Report (AIR) documents general technical data associated with many of the wheels used in the Air Force.
Standard

Maintainability Recommendations for Aircraft Wheel and Hydraulically Actuated Brake Design
2022-07-13
WIP
ARP813D

This SAE Aerospace Recommended Practice (ARP) recommends the maintainability features which should be considered in the design of aircraft wheels and brakes. The effect on other factors, such as, cost, weight, reliability, and compatibility with other systems should be weighed before the incorporation of any of these maintainability features into the design.

123Next >Last >>
X