Search Results

Two different types of mesh used for diesel combustion with the KIVA-4 code are compared. One is a well established conventional KIVA-3 type polar mesh. The other is a non-polar mesh with uniform size throughout the piston bowl so as to reduce the number of cells and to improve the quality of the cell shapes around the cylinder axis which can contain many fuel droplets that affect prediction accuracy and the computational time. This mesh is specialized for the KIVA-4 code which employs an unstructured mesh. To prevent dramatic changes in spray penetration caused by the difference in cell size between the two types of mesh, a recently developed spray model which reduces mesh dependency of the droplet behavior has been implemented. For the ignition and combustion models, the Shell model and characteristic time combustion (CTC) model are employed.

An integrated system model containing sub-models for diesel engine, emissions, and aftertreatment devices has been developed. The objective is to study engine-device and device-device interactions. The emissions sub-models used are for NOx and PM (particulate matter) prediction. The aftertreatment sub-models used include a diesel oxidation catalyst (DOC) and a diesel particulate filter (DPF). Controllers have also been developed to allow for transient simulations, active DPF regeneration, and prevention/control of runaway DPF regenerations. The integrated system-level model has been used to simulate DPF regeneration via exhaust fuel injection ahead of the DOC. In addition, the controller model can use intake throttling to assist in active DPF regeneration if needed. Regeneration studies have been done for both steady engine load and with load transients. High to low engine load transients are of particular interest because they can lead to runaway DPF regeneration.

Two turbulent combustion modeling approaches, which were large eddy simulations in conjunction with detailed kinetics (LES-CHEMKIN) and Reynolds Averaged Navier Stokes with detailed kinetics (RANS-CHEMKIN), were used to model two partially premixed engine conditions. The results were compared with average pressure and heat release data, as well as images of in-cylinder ignition chemiluminescence and OH radical distributions. Both LES-CHEMKIN and RANS-CHEMKIN match well with experimental average data. However, LES-CHEMKIN has advantages over RANS-CHEMKIN in predicting the details of location of ignition sites, temperature as well as OH radical distributions. Therefore, LES offers more realistic representations of the combustion process. As a further improvement aiming at saving computational cost and accounting for turbulence-chemistry interactions, a flamelet time scale (FTS) combustion model is coupled with CHEMKIN to predict the entire combustion process. In this new approach (i.e.

A general combustion model, in the context of large eddy simulations, was developed to simulate the full range of combustion in conventional diesel-type and HCCI-type diesels. The combustion model consisted of a Chemkin sub-model and an Extended Flamelet Time Scale (EFTS) sub-model. Specifically, Chemkin was used to simulate auto-ignition process. In the post-ignition phase, the combustion model was switched to EFTS. In the EFTS sub-model, combustion was assumed to be a combination of two elementary combustion modes: homogeneous combustion and flamelet combustion. The combustion index acted as a weighting factor blending the contributions from these two modes. The Chemkin sub-model neglected the subgrid scale turbulence-chemistry interactions whereas the EFTS model took them into account through a presumed PDF approach. The model was used to simulate an early injection mode of a Cummins DI diesel engine and a mode of a Caterpillar DI diesel engine.

System level modeling was used to develop a suitable control strategy for Diesel Homogeneous Charge Compression Ignition (HCCI) transient operation. Intake temperature and pressure, engine speed, engine load, cylinder wall temperature, exhaust gas recirculation, etc. all significantly affect combustion phasing generating a scenario where simple ECU mapping techniques prove inadequate. Two-stage fuels such as diesel fuel pose additional challenges for accurate combustion control. Low-temperature cool-flame chemical heat release can significantly alter the thermodynamic state of the trapped gaseous mixture and hence combustion phasing. Operator and environmentally induced transients can rapidly alter combustion phasing parameters suggesting a need for model-based control. A model-based control strategy featuring the identified essential physics has been developed to control diesel HCCI combustion phasing through transient operation.

An integrated system model containing sub-models for a multi-cylinder diesel engine, NOx and soot(PM) emissions, diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) has been developed to simulate the engine and aftertreatment systems at transient engine operating conditions. The objective of this work is two-fold; ensure correct implementation of the integrated system level model and apply the integrated model to understand the fuel economy trade-off for various DPF regeneration strategies. The current study focuses on a 1.9L turbocharged diesel engine and its exhaust system. The engine model was built in GT-Power and validated against experimental data at full-load conditions. The DPF model is calibrated for the current engine application by matching the clean DPF pressure drop for different mass flow rates. Load, boost pressure, speed and EGR controllers are tuned and linked with the current engine model.

Two advanced combustion models have been validated with the KIVA-3V Release 2 code in the context of two-stage combustion in a heavy duty diesel engine. The first model uses CHEMKIN to directly integrate chemistry in each computational cell. The second model accounts for flame propagation with the G-equation, and CHEMKIN predicts autoignition and handles chemistry ahead of and behind the flame front. A Damköhler number criterion was used in flame containing cells to characterize the local mixing status and determine whether heat release and species change should be a result of flame propagation or volumetric heat release. The purpose of this criterion is to make use of physical and chemical time scales to determine the most appropriate chemistry model, depending on the mixture composition and thermodynamic properties of the gas in each computational cell.

System-level models containing engine model, emission models, and aftertreatment device models have been developed. All the sub-models have been developed separately and come from a variety of different sources. A new phenomenological CO model recently has been coupled into the previous integrated model. The emission models, including PM (particulate matter), NOx, and CO are also calibrated from experimental data. Some modification has been added to improve the integrated model and accept different aftertreatment device models for future work. The objective of this work is to study the DPF (Diesel Particulate Filter) regeneration during transient operating conditions using the integrated model. The integrated system-level model is used to studying the dynamic performance between engine and aftertreatment system. In this study, the calibrated emission models are validated at transient operating conditions.

This work integrated a CA10 (crank angle at 10% heat release) controller into an integrated engine, emissions and aftertreatment model platform. Two CA10 phasing targets were chosen to analyze how advancing (or retarding) the target combustion phasing (CA10) affect the formation of NO and CO. The effect of intake valve closure (IVC) timing, which is the control mechanism for maintaining the target combustion phasing, on the cylinder trapped mass, and hence the charge temperature after compression is detailed. Finally, the relation between combustion phasing and the blow-down process leading to the exhaust process is discussed. Retarding the target combustion phasing by two degrees saw a 330 K drop in compressed charge temperature and a quadrupled reduction of peak NO emitted. Peak NO₂ emission reduced three times on account of the same. However, an increase in CO emission was observed when the combustion phasing was advanced.

This article presents nondestructive neutron computed tomography (nCT) measurements of Diesel Particulate Filters (DPFs) as a method to measure ash and soot loading in the filters. Uncatalyzed and unwashcoated 200cpsi cordierite DPFs exposed to 100% biodiesel (B100) exhaust and conventional ultra low sulfur 2007 certification diesel (ULSD) exhaust at one speed-load point (1500 rpm, 2.6 bar BMEP) are compared to a brand new (never exposed) filter. Precise structural information about the substrate as well as an attempt to quantify soot and ash loading in the channel of the DPF illustrates the potential strength of the neutron imaging technique.

A modeling study has been conducted in order to characterize the heat transfer in an automotive diesel exhaust system. The exhaust system model, focusing on 2 exhaust pipes, has been created using a transient 1-D engine flow network simulation program. Model results are in excellent agreement with experimental data gathered before commencement of the modeling study. Predicted pipe exit stream temperatures are generally within one percent of experimental values. Sensitivity analysis of the model was the major focus of this study. Four separate variables were chosen for the sensitivity analysis. These being the external convective heat transfer coefficient, external emissivity, mass flow rate of exhaust gases, and amplitude of incoming pressure fluctuations. These variables were independently studied to determine their contribution to changes in exhaust gas stream temperature and system heat flux. There are two primary benefits obtained from conducting this analysis.

Many commercial fuels, including gasoline and diesel, are multicomponent hydrocarbons. During the fuel vaporization process, the volatile components evaporate first, which dominate the region near the nozzle exit. The lately evaporated vapor with high penetration has high molecular weight. Thus, ignition and combustion of multicomponent fuels are not only influenced by distribution of fuel vapor mass fraction, but also by distribution of the components. This paper presents a spark ignition and combustion model with consideration of such multicomponent effects for GDI engines. Ignition kernel growth due to flame front propagation is considered in the model to eliminate the sensitivity of the numerical mesh size on the results.

The present study investigated HCCI combustion in a heavy-duty diesel engine both experimentally and numerically. The engine was equipped with a hollow-cone pressure-swirl injector using gasoline direct injection. Characteristics of HCCI combustion were obtained by very early injection with a heated intake charge. Experimental results showed an increase in NOx emission and a decrease in UHC as the injection timing was retarded. It was also found that optimization can be achieved by controlling the intake temperature together with the start-of-injection timing. The experiments were modeled by using an engine CFD code with detailed chemistry. The CHEMKIN code was implemented into KIVA-3V such that the chemistry and flow solutions were coupled. The model predicted ignition timing, cylinder pressure, and heat release rates reasonably well. The NOx emissions were found to increase as the injection timing was retarded, in agreement with experimental results.

The Rate-Controlled Constrained-Equilibrium (RCCE) method is applied to the numerical solution of methane-air combustion. The RCCE method offers a reduction in computation time for complex chemically reacting systems because the rate equations for a small number of slowly evolving constraints need to be solved. The current work focuses on presenting both the principles of the RCCE method and its application to methane-air Homogeneous Charge Compression Ignition (HCCI) combustion. This work takes into consideration some of the previously unexplored numerical issues associated with solving the RCCE equation set. Application of the RCCE method is first demonstrated in constant and variable volume adiabatic environments and compared to the integration of the full set of kinetic rate equations for each species. Results presented here show a reduction in computational time.

In this study, a one-equation LES sub-grid model from Menon, et al. [5] is used in simulating the diesel combustion process. In addition, based on the one-equation methodology of Menon et al., a new one-equation LES scalar transport model is formulated. These models allow for the turbulent transfer coefficients for both momentum and scalar flux to be determined independent of each other. The turbulent viscosity, μt, is determined as a function of the sub-grid kinetic energy, which is in turn determined from the one-equation model. The formulation for the scalar transfer coefficient, μs, is similar to that of the turbulent viscosity, yet is made to be consistent with scalar transport. Results for the LES momentum transfer are compared to experimental data of a backward facing step. This model, in conjunction with the LES scalar flux model, is verified by comparing with experimental data for a non-reacting turbulent jet.

DPF regenerations involve a trade-off between fuel economy and DPF durability. High temperature regenerations of DPFs have fewer fuel penalties but simultaneously tend to give higher substrate temperatures, which can reduce thermal reliability. In order to weaken the trade-off, the integrated system-level model [1,2,3,4] is used to conduct optimization studies and explore novel regeneration strategies for DPF aftertreatment devices. The integrated model developed in the Engine Research Center (ERC) includes sub-models for engines, emissions, aftertreatment devices and controllers. Based on the engine and regeneration fuel economy, multiple and single cycle regeneration tests are performed and analyzed. The optimal soot loadings to initiate and terminate regenerations are discussed. A pulsed regeneration strategy, which is characterized by injecting multiple pulses of fuel (upstream of a DOC) during regenerations, is investigated.

Large Eddy Simulation (LES) with a flamelet time scale combustion model is used to simulate diesel combustion. The flamelet time scale model uses a steady-state flamelet library for n-heptane indexed by mean mixture fraction, mixture fraction variance, and mean scalar dissipation rate. In the combustion model, reactions proceed towards the flamelet library solution at a time scale associated with the slowest reaction. This combination of a flamelet solution and a chemical time scale helps to account for unsteady mixing effects. The turbulent sub-grid stresses are simulated using a one-equation, non-viscosity LES model called the dynamic structure model. The model uses a tensor coefficient determined by the dynamic procedure and the subgrid kinetic energy. The model has been expanded to include scalar mixing and scalar dissipation. A new model for the conditional scalar dissipation has been developed to better predict local extinction.

A Soot-NOx Trap (SNT) is a combinatorial aftertreatment device intended to decrease both particulate and NOx emissions simultaneously. A system-level Soot-NOx Trap model was developed by adding Lean NOx Trap kinetics to a 1D Diesel Particulate Filter model. The hybrid model was validated against each parent model for the limiting cases, then exercised to investigate the interacting redox behavior. Modulations in temperature and exhaust air-fuel ratio were investigated for their ability to facilitate particulate oxidation and NOx reduction in the trap.

To help account for fuel distribution during combustion in diesel engines, a fuel film model has been developed and implemented into the KIVA-II code [1]. Spray-wall interaction and spray-film interaction are also incorporated into the model. Modified wall functions for evaporating, wavy films are developed and tested. The model simulates thin fuel film flow on solid surfaces of arbitrary configuration. This is achieved by solving the continuity, momentum and energy equations for the two dimensional film that flows over a three dimensional surface. The major physical effects considered in the model include mass and momentum contributions to the film due to spray drop impingement, splashing effects, various shear forces, piston acceleration, dynamic pressure effects, and convective heat and mass transfer.

A comprehensive system level modeling approach is used to understand the effects of the various physical actuators during diesel HCCI transients. Control concepts during transient operations are simulated using a set of actuators suitable for combustion control in diesel HCCI engines (intake valve actuation, injection timing, cooled EGR, intake boost pressure and droplet size). The impact of these actuating techniques on the overall engine performance is quantified by investigating the amount of actuation required, timing of actuation and the use of a combination of actuators. Combined actuation improved actuation space that can be used to phase combustion timing better and in extending the operating range. The results from transient simulations indicate that diesel HCCI operation would benefit from the combined actuation of intake valve closure, injection timing, boost and cooled EGR.