Refine Your Search

Topic

Author

Search Results

Technical Paper

Doppler Radar Speed Sensor for Anti-Skid Control System

1978-02-01
780857
A 24 GHz doppler speed sensor for skid controls has been developed. The microwave sensor is designed using both waveguide and thin-film technologies and assembled into a small integrated unit measuring 27 x 10 x 9 mm. The radar unit and the control circuitry are housed in a waterproof module of 94 x 140 x 78 mm. Part of the casing forms a horn antenna, which radiates a vertically polarized beam incident at 45° on the road surface, when mounted on the vehicle. The error in speed measuring is usually less than 10 percent.
Technical Paper

Wide-Range Air-Fuel Ratio Sensor, 1989

1989-02-01
890299
The detection range of an air-fuel ratio sensor is expanded in the rich A/F region. Using a simulation technique, the limiting cause of the detection range in the rich A/F region is identified as insufficient combustion rates of CO and H2 with O2 on the electrode, which prevent realization of a limited diffusion state which is necessary to detect the air-fuel ratio. Applying an improved diffusion layer to decrease the diffusion rates and an improved electrode to increase the combustion rates, it is demonstrated that the detection limit can be expanded to λ=0.6 while that of a conventional sensor is λ=0.8.
Technical Paper

CPU Model-based Hardware/Software Co-design for Real-Time Embedded Control Systems

2007-04-16
2007-01-0776
This paper proposes a new development method for highly reliable real-time embedded control systems using a CPU model-based hardware/software co-simulation. We take an approach that allows the full simulation of the virtual mechanical control system including CPU and object code level software. In this paper, Renesas SH-2A microcontroller model was developed on CoMET™ platform from VaST Systems Technology. A ETC (Electronic Throttle Control) system and engine control system were chosen to prove this concept. The ETB (Electronic Throttle Body) model on Saber® simulator from Synopsys® or engine model on MATLAB®/Simulink® simulator from MathWorks can be simulated with the SH-2A model. To help the system design, debug and evaluation, we developed an integrated behavior analyzer, which can display CPU behavior graphically during the simulation without affecting the simulation result, such as task level CPU load, interrupt statistics, software variable transition chart, and so on.
Technical Paper

Development of an On-Board Class A Local Area Network System

1992-02-01
920229
The growing number of electronic components used in automobiles lately has given rise to problems concerning the increasing number, size and weight of the wiring harnesses. As one approach to resolving these problems, the authors proposed a multiplex method based on the direction of signal flow in 1988 (SAE880589). However, the need to reduce the number of wiring harnesses circuits further made it necessary to develop a more sophisticated system. This paper presents an on-board Class A local area network (LAN) system that overcomes the problems in conventional multiplexing systems through the use of a master-slave configuration, a polling selection method and a system that integrates of electronic circuits with switch modules.
Technical Paper

Cold Start HC Reduction with Feedback Control Using a Crank Angle Sensor

2008-04-14
2008-01-1010
Emission regulations continue to be strengthened, and it is important to decrease cold start hydrocarbon concentrations in order to meet them, now and in the future. The HC concentration in engine exhaust gas can be reduced by optimizing the air-fuel ratio. However, a conventional air-fuel ratio feedback control does not operate for the first ten seconds after the engine has started because the air-fuel ratio sensor has not yet been activated. In this paper, we report on a study to optimize the air-fuel ratio using a crank angle sensor until the air-fuel ratio sensor has been activated. A difference in fuel properties was used as a typical disturbance factor. The control was applied to both a direct-injection engine (DI) and a port-injection engine (MPI). It was evaluated for two fuel types: one which evaporates easily and one which does not. The experimental results show the air-fuel ratio is optimized for both types of fuel.
Technical Paper

The Role of Sensors and Sensing Technology for Future Automotive Systems

1993-03-01
930358
The role of sensors and sensing technologies for the next generation vehicle systems are discussed. The control systems for engines and power-train are expected to realize high efficiency with low pollution and comfort drivability. Vehicular safety and chassis control systems are expected to avoid many kinds of traffic accidents caused by the human errors of drivers. Vehicular information systems will help the drivers to get the information to manage their vehicles economically and efficiency. In every system mentioned above, sensors and sensing technologies are playing an increasingly important role. This paper introduces and discusses essential technologies for sensors and sensing which can be expected to bring the solutions to the future automotive systems.
Technical Paper

A State Adaptive Control Algorism for Vehicle Suspensions

1988-11-01
881769
This paper describes a state adaptive control method for vehicle suspensions proposed by Hitachi, Ltd. The objective of the control is to improve riding comfort and driving stability in reaction to road iregularities, exterior wind forces, and changes in vehicle loads as well as in reaction to inertial changes during cornering, breaking, and accelerating. The objective is attained by making considerable use of the relative displacement data between the body and the suspension. The state adaptive control system includes four shock absorbers whose damping forces can be tuned in three stages, four height sensors which measure the relative displacement, a vehicle speed sensor, and a microcomputer which decides the optimal damper stage. The validity of the proposed control method is shown through computer simulations and actual driving experiments. Vertical acceleration is reduced by about 55 % by switching from the soft damper to the hard damper in a computer simulation.
Technical Paper

Optical Fiber Gyroscopes for Automobiles

1990-02-01
900490
This paper reviews the technological aspects and characteristics of optical fiber gyroscopes, and discusses their automotive applications. The optical system of an all-fiber gyroscope and the fiber optic components to build it are described. An optical phase modulation scheme to improve the sensitivity and the signal processing for the modulated output are discussed. The specifications of some packaged optical fiber gyroscopes are explained. An earth's rotation detection experiment is demonstrated to show the higher performance. The potential automotive related applications of the gyroscope are forecasted. One of the off-board uses of the sensor is the vibration measurements of a vehicle. When used onboard, the optical fiber gyroscopes will improve the navigation accuracy. A navigation result utilized the sensor with a map matching algorithm is reported. The gyroscopes may also be applied to future chassis controls.
Technical Paper

A Totally Integrated Vehicle Electronic Control System

1988-11-01
881772
A totally integrated vehicle electronic control system is described, which optimizes vehicle performance through use of electronics. The system implements efficient coordination of functions of the engine, drive-train, brakes, steering, and suspension control subsystems to give a smoother ride, better handling and greater safety. The principles of the system are based on control and stability augmentation strategies. Each subsystem has two observers which control the force of the actuators according to the vehicle dynamics. The system features a driver support system which allows the average driver to employ the full performance potential of the vehicle in exceptional situations, and an artificial response control system to ensure optimum response and comfort. Application of the system allows the driver to experience a new level of performance and a marked improvement in handling quality and ride comfort.
Technical Paper

Optical Multiplexed Transmission System using High Temperature Polymer Fiber

1989-02-01
890200
A multiplexed transmission system utilizing newly developed optical polymer has been proposed. The system is composed of a star-shaped optical network, in which optical signals can be transmitted bi-directionally through a fiber and optical branches between the central and local controllers. The new polymer optical fiber has been developed and adopted for this system, and it was designed to be durable to the high temperature in automotive engine rooms. The high temperature resistibility of the fiber has been achieved with utilization of a thermo-setting resin for the core materials. The optical loss characteristics of the fiber is as low as 0.50 dB/m at 660 nm wavelength.
Technical Paper

A Virtual ECU and Its Application to Control System Analysis - Power Window System Demonstration

2016-04-05
2016-01-0022
A virtual power window control system was built in order to look into and demonstrate applications of microcontroller models. A virtual ECU simulated microcontroller hardware operations. The microcontroller program, which was written in binary digital codes, was executed step-by-step as the virtual ECU simulation went on. Thus, production-ready codes of ECUs are of primary interest in this research. The mechanical system of the power window, the DC motor to lift the window glass, the H-bridge MOSFET drivers, and the current sensing circuit to detect window locking are also modeled. This means that the hardware system of the control system was precisely modeled in terms of mechanical and circuit components. By integrating these models into continuous and discrete co-simulation, the power window control system was analyzed in detail from the microscopic command execution of the microcontroller to the macroscopic motion of the window mechanism altogether.
Technical Paper

Method for Determining Thermal Resistances in Coupled Simulator: For Electric Valve Timing Control System

2015-04-14
2015-01-1301
We developed a thermal calculation 1D simulator for an electric valve timing control system (VTC). A VTC can optimize the open and close timing of the intake and exhaust valves depending on the driving situation. Since a conventional VTC is driven hydraulically, the challenges are response speed and operation limit at low temperature. Our company has been developing an electric VTC for quick response and expansion of operating conditions. Currently, it is necessary to optimize the motor and reduction gear design to balance quicker response with downsizing. Therefore, a coupled simulator that can calculate electricity, mechanics, control, and thermo characteristics is required. In 1D simulation, a thermal network method is commonly used for thermal calculation. However, an electric VTC is attached to the end of a camshaft; therefore, determining thermal resistances is difficult. We propose a method of determining thermal resistances, using both theoretical and experimental approaches.
Technical Paper

EMERALDS-OSEK: A Small Real-Time Operating System for Automotive Control and Monitoring

1999-03-01
1999-01-1102
Increasingly, microcontrollers are being used in automotive systems to handle sophisticated control and monitoring activities. As applications become more sophisticated, their design and development becomes complex, necessitating the use of an operating system to manage the complexity and provide an abstraction for improving portability of code. This paper presents EMERALDS-OSEK, an operating system we have designed and implemented based on OSEK/VDX, an open industry standard. We present some of the features and optimizations that make EMERALDS-OSEK appropriate for small, low-cost microcontrollers typically found in automotive applications. We also present measurements of operating system performance. We find EMERALDS-OSEK to be efficient, both in terms of processing overheads and memory usage. However, we also find some parts of the OSEK standard that may be improved, and present our ideas for such improvements.
Technical Paper

Smooth Gear Shift Control Technology for Clutch-to-Clutch Shifting

1999-03-01
1999-01-1054
An automatic transmission without a one-way clutch for a small sized, light weight automatic transmission is presented. The factor of torque fluctuation occurrence during shifting of the transmission increases so that the shifting is executed by controlling two wet clutches electronically in place of the one-way clutch and the wet clutch. Therefore, it is necessary to develop a new smooth gear shift control technology for clutch-to-clutch shifting on an automatic transmission without a one-way clutch. The control technology has desirable clutch-to-clutch shift control, learning control and robust control which apply to accurate signals obtained by an observation method. Smooth shifts during clutch-to-clutch shifting can be realized by recognizing clutch change-over time using a calculated acceleration and an input/output speed ratio of the transmission.
Technical Paper

A New RISC Microcontroller with On-Chip FPU to Introduce Adaptive Control into Powertrain Management

1999-03-01
1999-01-0865
Gasoline engine control continues to become more sophisticated and so the amount of software has reached 10 to 20 times that of early control systems. By changing the embedded microcomputer from 8bit CISC (Complex Instruction Set Computer) to 32bit RISC (Reduced Instruction Set Computer), processing performance has been improved 100 times. This paper evaluates quantitative performance of the RISC CPU having a FPU (Floating Point Processing Unit) and describes an example application to adaptive control.
Technical Paper

Feasible Study for the Availability of Electric Vehicles for the Stable Operation in Power System Network

2011-05-17
2011-39-7248
Electric vehicle will come into wide use in worldwide with the arrival of the Low-carbon society in the next twenty years. And total capacity of the battery on the electric vehicle in the power system network amounts for several Giga Watts, which corresponds to the capacity of several nuclear power plants. It is difficult for power system operator to forecast of the amount of the charging power because there is much uncertainty of using power on electric vehicles compared to the electric facility like air conditioner and so on. In order to operate the power system network stable, it is necessary for power system operator to control charging power of electric vehicle independently as controllable facilities. We propose a “Smart Charging” concept based on the index for the security monitoring of power system network which makes power system operation more efficiently and makes electric vehicle owners more conveniently.
Technical Paper

Computer-Aided Calibration Methodology for Spark Advance Control Using Engine Cycle Simulation and Polynomial Regression Analysis

2007-10-29
2007-01-4023
The increasing number of controllable parameters in modern engine systems has led to increasingly complicated and enlarged engine control software. This in turn has created dramatic increases in software development time and cost. Model-based control design seems to be an effective way to reduce development time and costs and also to enable engineers to understand the complex relationship between the many controllable parameters and engine performance. In the present study, we have developed model-based methodologies for the engine calibration process, employing engine cycle simulation and regression analysis. The reliability of the proposed method was investigated by validating the regression model predictions with measured data.
Technical Paper

Evaluation of Parallel Executions on Multiple Virtual ECU Systems

2018-04-03
2018-01-0011
We have developed a cooperative simulation environment for multiple electronic control units (ECUs) including a parallel executions mechanism to improve the test efficiency of a system, which was designed with multiple ECUs for autonomous driving. And we have applied it to a power window system for multiple ECUs with a controller area network (CAN). The power window model consists of an electronic-mechanical model and a CPU model. Each simulator with a different executions speed operates in parallel using a synchronization mechanism that exchanges data outputted from each simulator at a constant cycle. A virtual ECU simulated microcontroller hardware operations and executed its control program step-by-step in binary code to test software for the product version. As co-simulation technology, a mechanism that synchronously executes heterogeneous simulators and a model of an in-vehicle communication CAN connecting each ECU were developed.
Technical Paper

Study on Mixture Formation and Ignition Process in Spark Ignition Engine Using Optical Combustion Sensor

1990-09-01
901712
Mixture formation and the ignition process in 4 cycle 4 cylinder spark ignition engines were investigated, using an optical combustion sensor that combines fiber optics with a conventional spark plug. The sensor consists of a 1-mm diameter quartz glass optical fiber cable inserted through the center of a spark plug. The tip of the fiber is machined into a convex shape to provide a 120-degree view of the combustion chamber interior. Light emitted by the spark discharge between spark electrodes and the combustion flames in the cylinder is transmitted by the optical cable to an opto-electric transducer. As a result, the ignition and combustion process which depends on the mixture formation can be easily monitored without installing transparent pistons and cylinders. This sensor can give more accurate information on mixture formation in the cylinders.
Technical Paper

An Accurate Torque-based Engine Control by Learning Correlation between Torque and Throttle Position

2008-04-14
2008-01-1015
In recent years, integrated vehicle control systems have been developed to improve fuel economy and safety. As a result, engine control is shifting to torque-based systems for throttle / fuel / ignition control, to realize an engine torque demand from the system. This paper describes torque-based engine control technologies for SI (Spark Ignition) engine to improve torque control accuracy using a feedback control algorithm and an airflow sensor.
X