Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Spark Arrester Test Carbon

2013-03-26
CURRENT
J997_201303
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Spark Arrester Test Carbon

1990-09-01
HISTORICAL
J997_199009
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Spark Arrester Test Carbon

1988-06-01
HISTORICAL
J997_198806
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Spark Arrester Test Carbon

1988-10-01
HISTORICAL
J997_198810
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Voltage Regulators for Automotive-Type Generators

2006-01-09
CURRENT
J2669_200601
This SAE Definition Document contains historic voltage regulation methods and test requirements that have not been previously published. The purpose of this document is to recommend a set of definitions and practices for use on current and future 12 V vehicle electric power regulation and control systems in internal combustion engine road vehicles. This document is not intended to include nor exclude regulators used in higher voltage vehicle electrical systems. The term “generator” rather than “alternator” will be used even though these terms may be used interchangeably in practice.
Standard

Pneumatic Spring Terminology

2016-04-01
CURRENT
J511_201604
This pneumatic spring terminology has been developed to assist engineers and designers in the preparation of specifications and descriptive material relating to pneumatic springs and their components. It does not include gas supply or control systems.
Standard

PNEUMATIC SPRING TERMINOLOGY

1989-06-01
HISTORICAL
J511_198906
This pneumatic spring terminology has been developed to assist engineers and designers in the preparation of specifications and descriptive material relating to pneumatic springs and their components. It does not include gas supply or control systems.
Standard

Brake Hydraulic Component Flow Rate Measurement for High Differential Pressure (>5 bar)

2017-05-18
CURRENT
J3052_201705
This recommended practice provides a method, test set-up, and test conditions for brake hydraulic component flow rate measurement for high differential pressure (>5 bar) flow conditions. It is intended for hydraulic brake components which affect the brake fluid flow characteristics in a hydraulic brake circuit, that are part of a circuit for which the flow characteristics are important to system operation, and that are exposed to high operating pressure differentials (in the 5 to 100 bar range). Typical applications may include measurement of flow through chassis controls valve bodies, orifices in the brake system such as in flow bolts, junction blocks, and master cylinders, and through brake pipe configurations.
Standard

MANUAL CONTROLS FOR MATURE DRIVERS

1997-10-01
CURRENT
J2119_199710
Since little data exists to provide appropriate values for control parameters that would be appropriate for mature drivers, the following recommendations are of a general nature. However, they are based upon the current understanding of the aging processes that characterize mature drivers. Notwithstanding the lack of an extensive amount of data in this field, the dissemination of this SAE Information Report is considered to be appropriate and timely in light of the large increase in the number of mature drivers on the public roads, and because of the need to at least initiate efforts toward developing an information report covering this issue. It is realized that there may be cases where specific recommendations may conflict with vehicle packaging and/or operational requirements. Deviation from the recommendations may be necessary and permissible to achieve the best overall system performance.
Standard

Two-Stroke-Cycle Gasoline Engine Lubricants Performance and Service Classification

2003-07-31
CURRENT
J2116_200307
This SAE Standard was prepared by Technical Committee 1, Engine Lubrication, of SAE Fuels and Lubricants Council. The intent is to improve communications among engine manufacturers, engine users, and lubricant marketers in describing lubricant performance characteristics. The key objective is to ensure that a correct lubricant is used in each two-stroke-cycle engine.
Standard

High Temperature Materials for Exhaust Manifolds

1999-08-01
HISTORICAL
J2515_199908
A subcommittee within SAE ISTC Division 35 has written this report to provide automotive engineers and designers a basic understanding of the design considerations and high temperature material availability for exhaust manifold use. It is hoped that it will constitute a concise reference of the important characteristics of selected cast and wrought ferrous materials available for this application, as well as methods employed for manufacturing. The different types of manifolds used in current engine designs are discussed, along with their range of applicability. Finally, a general description of mechanical, chemical, and thermophysical properties of commonly-used alloys is provided, along with discussions on the importance of such properties.
Standard

High Temperature Materials for Exhaust Manifolds

2017-12-20
CURRENT
J2515_201712
A subcommittee within SAE ISTC Division 35 has written this report to provide automotive engineers and designers a basic understanding of the design considerations and high temperature material availability for exhaust manifold use. It is hoped that it will constitute a concise reference of the important characteristics of selected cast and wrought ferrous materials available for this application, as well as methods employed for manufacturing. The different types of manifolds used in current engine designs are discussed, along with their range of applicability. Finally, a general description of mechanical, chemical, and thermophysical properties of commonly-used alloys is provided, along with discussions on the importance of such properties.
Book

The Global Market for Automotive Turbochargers: 2015 edition

2015-10-01
Since the last edition of this report in 2013, the demand on automakers has been relentless in terms of improving fuel economy and reducing emissions, thus driving increased sales of forced induction systems. The use of pressure charging techniques has therefore expanded significantly. Recent years have seen the ascendancy of the turbocharger and its use by almost every major global manufacturer.
X