Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

SAE MANUAL ON BLAST CLEANING

1968-06-01
CURRENT
J792A_196806
Blast cleaning may be defined as a secondary manufacturing process in which a suitable stream of solid particles is propelled with sufficient velocity against a work surface to cause a cleaning or abrading action when it comes in contact with the workpiece. As indicated in the definition, blast cleaning may be employed for a variety of purposes. Ordinarily, it is considered as a method for removing sand from castings, burrs or scale from forgings, mill products, or heat treated parts; to promote machinability, and to minimize the possibility of interference in actual operation. In addition to this use, blast cleaning also produces an excellent surface for industrial coatings. All these objectives are often accomplished in the one operation.
Standard

Spark Arrester Test Carbon

2013-03-26
CURRENT
J997_201303
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Spark Arrester Test Carbon

1990-09-01
HISTORICAL
J997_199009
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Spark Arrester Test Carbon

1988-06-01
HISTORICAL
J997_198806
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Spark Arrester Test Carbon

1988-10-01
HISTORICAL
J997_198810
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Diesel Injection Pump Testing—Part 2: Orifice Plate Flow Measurement

2015-09-22
CURRENT
J968/2_201509
This part of SAE J968 specifies the flow measuring system, including the fixture, to be used for flow testing the single hole orifice plates used in an orifice plate type nozzle and holder assembly (described in SAE J968-1) which is intended for testing and setting diesel fuel injection pumps on test benches. The flow measuring system and fixture ensure accurate flow testing of the entire range of orifices from 0.4 to 0.8 mm diameter as specified in SAE J968-1. It is intended primarily for use by the manufacturers of single hole orifice plates.
Standard

Diesel Injection Pump Testing—Part 2: Orifice Plate Flow Measurement

2002-12-20
HISTORICAL
J968/2_200212
This part of SAE J968 specifies the flow measuring system, including the fixture, to be used for flow testing the single hole orifice plates used in an orifice plate type nozzle and holder assembly (described in SAE J968-1) which is intended for testing and setting diesel fuel injection pumps on test benches. The flow measuring system and fixture ensure accurate flow testing of the entire range of orifices from 0.4 to 0.8 mm diameter as specified in SAE J968-1. It is intended primarily for use by the manufacturers of single hole orifice plates.
Standard

Voltage Regulators for Automotive-Type Generators

2006-01-09
CURRENT
J2669_200601
This SAE Definition Document contains historic voltage regulation methods and test requirements that have not been previously published. The purpose of this document is to recommend a set of definitions and practices for use on current and future 12 V vehicle electric power regulation and control systems in internal combustion engine road vehicles. This document is not intended to include nor exclude regulators used in higher voltage vehicle electrical systems. The term “generator” rather than “alternator” will be used even though these terms may be used interchangeably in practice.
Standard

Brake-Stroke Indicator Design Guideline for Cam or Disc Air-Brake Actuators

2018-05-07
CURRENT
J1953_201805
This SAE Recommended Practice shall cover mechanical-brake adjustment limit stroke indicators for actuators with visible exposed pushrods and electrical-brake adjustment limit stroke indicators for all air-brake actuators. This device shall indicate the foundation brake(s) may require adjustment or service when inspected per vehicle manufacturer's procedures. A measurement shall be made to determine actual stroke measurement for any system not factory calibrated. Stroke indication accuracy of an air-brake actuator can be assured only when all of its components are supplied by the original brake actuator manufacturer.
Standard

Brake-Stroke Indicator Design Guideline for Cam or Disc Air-Brake Actuators

2012-06-19
HISTORICAL
J1953_201206
This SAE Recommended Practice shall cover mechanical- readjust stroke indicators for actuators with visible exposed pushrods and electrical-readjust stroke indicators for all air-brake actuators. This device shall indicate the foundation brake(s) may require adjustment or service when inspected per vehicle manufacturer's procedures. A measurement shall be made to determine actual stroke measurement for any system not factory calibrated. Stroke indication accuracy of an air-brake actuator can be assured only when all of its components are supplied by the original brake actuator manufacturer.
Standard

SINTERED CARBIDE TOOLS

1977-02-01
HISTORICAL
J439_197702
This recommended practice covers methods for measuring or evaluating five properties or characteristics of sintered carbide which contribute significantly to the performance of sintered carbide tools. These properties are: hardness, specific gravity, apparent porosity, structure, and grain size. They are covered under separate headings below.
X