Refine Your Search

Topic

Author

Search Results

Standard

Vehicle Electromagnetic Immunity--On-Board Transmitter Simulation

2009-08-03
CURRENT
J551/12_200908
This part of SAE J551 specifies on-board transmitter simulation test methods and procedures for testing passenger cars and commercial vehicles. The electromagnetic disturbances considered in this part of SAE J551 are limited to continuous narrow band electromagnetic fields. SAE J551/1 specifies general, definitions, practical use, and basic principles of the test procedure.
Standard

Heavy Duty OBD IUMPR Data Collection Tool Process

2018-09-04
CURRENT
J3162_201809
This document describes the collection of IUMPR data required by the Heavy Duty On-Board Diagnostic regulation 13 CCR 1971.1 (l)(2.3.3), using SAE J1939-defined messages incorporated in a suite of software functions.
Standard

Air Dryer Test Procedure

2012-11-09
CURRENT
J2384_201211
This SAE Recommended Practice establishes uniform Test Procedures for desiccant Air Dryers used in vehicles with compressed air systems per SAE J2383. Continuous flow desiccant Air Dryers are excluded from the scope of this document.
Standard

Motorcycle and Motor Driven Cycle Electrical System Maintenance of Design Voltage

2003-01-09
HISTORICAL
J392_200301
This SAE Recommended Practice pertains to electrical systems of motorcycles both with and without batteries. Purpose This document provides minimum illumination voltage values for all motorcycle classifications as specified in SAE J213 describes test procedures to determine that these voltages are maintained.
Standard

Motorcycle and Motor Driven Cycle Electrical System Maintenance of Design Voltage

1984-05-01
HISTORICAL
J392_198405
This SAE Recommended Practice pertains to electrical systems of motorcycles both with and without batteries. Purpose This document provides minimum illumination voltage values for all motorcycle classifications as specified in SAE J213 describes test procedures to determine that these voltages are maintained.
Standard

Nomenclature - Wheels, Hubs, and Rims for Commercial Vehicles

2017-10-23
CURRENT
J393_201710
This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, hubs, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define functional truck wheel, hub, and rim designs. For nomenclature specific to “passenger-type” disc wheels, refer to SAE J1982. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.
Standard

Motorcycle and Motor Driven Cycle Electrical System Maintenance of Design Voltage

1969-12-01
HISTORICAL
J392_196912
This SAE Recommended Practice pertains to electrical systems of motorcycles both with and without batteries. Purpose This document provides minimum illumination voltage values for all motorcycle classifications as specified in SAE J213 describes test procedures to determine that these voltages are maintained.
Standard

Hole Spacing for Scraper and Dozer Cutting Edges

1983-05-01
HISTORICAL
J737_198305
This standard is intended for cutting edge sections used on: a. Tractor-scrapers as described in SAE J1057 and J728 b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted. This standard specifies hole placement along with length and width of the cutting edge.
Standard

Hole Spacing for Scraper and Dozer Cutting Edges

2007-08-30
CURRENT
J737_200708
This standard is intended for cutting edge sections used on: a. Tractor-scrapers as described in SAE J1057 and J728 b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted. This standard specifies hole placement along with length and width of the cutting edge.
Standard

Cutting Edge-Curved Grader

2007-08-30
CURRENT
J739_200708
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580. This document specifes hole placement along the length and width of the cutting edge and dimensions for cutting edge cross sections. See Table 1.
Standard

Loading Ability Test Procedure - Scrapers

2011-10-27
CURRENT
J764_201110
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
Standard

Voltages for Diesel Electrical Systems

1976-09-01
HISTORICAL
J539A_197609
This SAE Recommended Practice is intended to apply to lamps, batteries, heaters, radios, and similar equipment for operation with mobile or automotive diesel engines. Twenty-four V systems have long been used for heavy duty services because 24 V permit operating 12 V systems in series-parallel. Thirty-two V systems have been used for marine, railroad-car lighting, and other uses. Generators, storage batteries, starting motors, lighting, and auxiliary electrical equipment shall be for nominal system ratings of 12, 24, or 32 V as determined by the power requirements of the application. It is recommended that no intermediate voltages be considered. The combination of a 24 V starting motor and two 12 V batteries connected in series for cranking is considered practice where it can be adapted to the installation.
Standard

Brake Block Chamfer

2011-05-17
CURRENT
J662_201105
The scope of this SAE Standard is to provide a uniform chamfer on brake blocks.
Standard

Transport Area Network Cabling

2011-06-30
CURRENT
J2496_201106
This series of SAE Recommended Practices was developed to provide an open architecture system for on-board electronic systems. It is the intention of these documents to allow electronic devices to communicate with each other by providing a standard architecture. This particular document describes the Network Interface and Cabling which defines the requirements needed for communicating between devices that are on different segments of the SAE J2496 Transport Area Network. While these recommended practices may be used in retrofitting older vehicles, the primary intent is for implementation in new bus procurements.
X