Refine Your Search

Topic

Author

Affiliation

Search Results

Book

Honda R&D Technical Review April 2021

2021-04-01
Honda R&D Technical Review is a periodical containing research papers related to Honda R&D Center activities worldwide that cover automobile, motorcycle, power products, aircraft engine, and other fundamental technologies. Honda Motor offers a book for the April 2021 issue with 104 pages containing 12 papers focusing on the following latest topics: Technology for Prediction of Contactor Noise for Electric-powered Vehicle Batteries Reduction of Internal Resistance in High Capacity Lithium-ion Batteries with 3D Lattice-structured Electrode Predictive Technique for Seat Belt Submarining Injury by Triaxial Iliac Load Cell
Software

SAE J2008 - Recommended Organization of Vehicle Service Information for Interchange on CD-ROM

1998-12-30
SAE J2008 Recommended Organization of Vehicle Service Information for Interchange Access to accurate service information is critical for the diagnosis and repair of increasingly complex vehicle systems. Though aftermarket technicians perform a significant amount of this service and repair, they do not have fast, easy access to this important information. If proper procedures are not readily available, the technician may use a less effective technique that could directly impact the vehicle's performance. The goal of SAE J2008 is to enable manufacturers to standardize vehicle service information in order to increase technician familiarity and reduce search time with easy data retrieval. SAE J2008 on CD-ROM brings you the information you need to standardize your vehicle service information—today.
Standard

Combination Tail and Floodlamp for Industrial Equipment

2003-05-15
CURRENT
J94_200305
This SAE Standard provides performance and general design requirements and related test procedures for a combination tail and floodlamp for use on industrial wheeled equipment that may be operated on public roads.
Standard

TOLERANCES, METRIC Aluminum Alloy Drawn Tubing

1994-04-01
MAM2203A
This specification covers established metric manufacturing tolerances applicable to aluminum alloy drawn tubing ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" applies only to the higher figure of the specified range.
Standard

TOLERANCES, METRIC Aluminum Alloy Drawn Tubing

2002-07-23
MAM2203
This specification covers established metric manufacturing tolerances applicable to aluminum alloy drawn tubing ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" applies only to the higher figure of the specified range.
Standard

COMMUNICATIONS MANAGEMENT UNIT (CMU) MARK 2

2019-11-26
CURRENT
ARINC758-4
This ARINC Standard specifies the ARINC 758 Mark 2 Communications Management Unit (CMU) as an on-board message router capable of managing various datalink networks and services available to the aircraft. Supplement 4 adds Ethernet interfaces, per ARINC Specification 664 Part 2. This will allow the CMU to communicate with IP based radio transceivers (e.g., L-Band Satellite Communication Systems (Inmarsat SwiftBroadband (SBB) and Iridium Certus), ACARS over IP, AeroMACS, etc.).
Standard

LOGICAL SOFTWARE PART PACKAGING FOR TRANSPORT

2020-11-16
CURRENT
ARINC641-1
The purpose of this standard is to provide a method for packaging aircraft software parts for distribution using contemporary media or by electronic distribution. This project intends to standardize and provide guidance for the storage of floppy based software, currently packaged in media set parts. This standard format can be then stored or distributed on a single physical media member (CD-ROM), or by electronic crate. The obsolescence of floppy disks drive an urgent need for this guidance.
Standard

Manufacturing Message Specification – Service Definition and Protocol

2016-06-28
CURRENT
EIA511
The Manufacturing Message Specification is an application layer Standard designed to support messaging communications to and from programmable devices in a Computer Integrated Manufacturing (CIM) environment. This environment is referred to in this Standard as the manufacturing environment. This Standard does not specify a complete set of services for remote programming of devices, although provision of such a set of services may be the subject of future standardization efforts.
Standard

BITE GLOSSARY

1986-12-18
CURRENT
ARINC612
The purpose of this standard is to provide a source of definitions of terms and acronyms commonly used in the air transport maintenance community for test and evaluation with an emphasis on terms applicable to BITE.
X