Search Results

To provide a means of obtaining the efficiency characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. For 4WD/AWD, it does not include transfer case or power take off subsystems. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing.

To provide a means of obtaining the performance characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing. However, by its very nature a transmission should be viewed as a compilation of three major component systems: pump, torque converter, and gearbox (all ratio change elements).

The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The transmission characteristics to be determined for all driving ranges or gears are: 1 Efficiency versus output speed. 2 Torque ratio versus output speed. 3 Input speed versus output speed. 4 Output torque versus output speed. 5 Parasitic losses versus input speed.

To provide a means of comparing the performance characteristics of automatic transmissions. It outlines dynamometer tests that cover the range of operation of transmissions and provides a method of presenting the test data. This procedure must be followed with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete assembly driven by the engine and used to effect a ratio change in transmitting power to the final drive system.

The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a Torque ratio versus speed ratio and output speed b Input speed versus speed ratio and output speed c Efficiency versus speed ratio and output speed d Capacity factor versus speed ratio and output speed e Input torque versus input speed NOTE: For more information about these characteristics and the design of hydrodynamic drives, see “Design Practices—Passenger Car Automatic Transmissions,” SAE Advances in Engineering, AE18 or AE29

The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a Torque ratio versus speed ratio and output speed b Input speed versus speed ratio and output speed c Efficiency versus speed ratio and output speed d Capacity factor versus speed ratio and output speed e Input torque versus input speed NOTE: For more information about these characteristics and the design of hydrodynamic drives, refer to “Design Practices: Passenger Car Automatic Transmissions,” SAE Advances in Engineering, AE-18 (Third Ed.) or AE-29 (Fourth Ed.).

The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a Torque ratio versus speed ratio and output speed b Input speed versus speed ratio and output speed c Efficiency versus speed ratio and output speed d Capacity factor versus speed ratio and output speed e Input torque versus input speed NOTE: For more information about these characteristics and the design of hydrodynamic drives, refer to “Design Practices: Passenger Car Automatic Transmissions,” SAE Advances in Engineering, AE-18 (Third Ed.) or AE-29 (Fourth Ed.).

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

This SAE Recommended Practice provides a method to determine the performance characteristics of the hydraulic oil pumps used in automatic transmissions and automatic transaxles. This document outlines the specific tests that describe the performance characteristics of these pumps over a range of operating conditions and the means to present the test data. This document is not intended to assess pump durability.

This SAE Recommended Practice provides a method to determine the performance characteristics of the hydraulic oil pumps used in automatic transmissions and automatic transaxles. This document outlines the specific tests that describe the performance characteristics of these pumps over a range of operating conditions and the means to present the test data. This document is not intended to assess pump durability.