Standard
AS882 Pin - Trim Control
1941-06-02
CURRENT
AS882-2
No scope available.
Search Results
Standard
Guidelines for Developing and Revising SAE Nomenclature and Definitions
1976-02-01
HISTORICAL
J1115_197602
Standard
Steel Tubing (Seamless for Machined Parts) 1.8ni 0.80cr 0.25mo (0.38 - 0.43c) Heat Treated (200,000 Tensile Strength)
2002-12-16
CURRENT
AMS6420
Standard
Steel Tubing (Seamless for Machined Parts) .55ni .25mo (.33 - .38c) Normalized Or Heat-Treated (90,000 Tensile Strength)
2002-12-16
CURRENT
AMS6283
Standard
Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.35 - .38c) Heat-Treated (125,000 Tensile Strength)
2002-12-16
CURRENT
AMS6284
Standard
Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.38 - .43c) Heat-Treated (180,000 Tensile Strength)
2002-12-16
CURRENT
AMS6285
Standard
Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.38-.43c) Heat-Treated (180,000 T.S.)
2002-12-16
CURRENT
AMS6286
Standard
NUTS, SELF-LOCKING, STEEL High Strength, Prevailing-Torque, All Metal 450 F (232 C) Use, Unified "J" (MIL-S-8879) Thread Form
1969-11-01
HISTORICAL
AMS7252
Standard
NUTS, SELF-LOCKING, STEEL High Strength, All Metal 450° F (230° C) Use, Unified "J" (MIL-S-8879) Thread Form
1980-01-15
HISTORICAL
AMS7252B
This specification covers all-metal, self-locking nuts, plate nuts, and gang channel nuts made of a carbon or low-alloy steel.
Standard
NUTS, SELF-LOCKING, STEEL High Strength, Prevailing Torque, All Metal 450° F (232° C) Use, Unified "J" (MIL-S-8879) Thread Form
1973-05-15
HISTORICAL
AMS7252A
This specification covers all-metal, self-locking, prevailing-torque nuts, plate nuts, and gang channel nuts made of a carbon or low-alloy steel.
Standard
BOLTS AND SCREWS, TITANIUM ALLOY 6Al - 4V Upset Headed, Heat Treated, Roll Threaded
1973-05-15
HISTORICAL
AMS7461B
This specification covers premium quality bolts and screws made of 6Al - 4V titanium alloy.
Standard
BOLTS AND SCREWS, TITANIUM ALLOY 6Al - 4V Upset Headed, Heat Treated, Roll Threaded
1970-11-01
HISTORICAL
AMS7461A
Standard
BOLTS AND SCREWS, TITANIUM ALLOY 6Al - 4V Upset Headed, Heat Treated, Roll Threaded
1964-06-30
HISTORICAL
AMS7461
Standard
Combination Tail and Floodlamp for Industrial Equipment
2003-05-15
CURRENT
J94_200305
This SAE Standard provides performance and general design requirements and related test procedures for a combination tail and floodlamp for use on industrial wheeled equipment that may be operated on public roads.
Standard
Alignment of Nut Slots
1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard
Round Head Bolts
1990-01-01
CURRENT
J481_199001
Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.
Standard
TOLERANCES, METRIC Aluminum Alloy Drawn Tubing
1994-09-01
MAM2203B
Standard
TOLERANCES, METRIC Aluminum Alloy Drawn Tubing
1994-04-01
MAM2203A
This specification covers established metric manufacturing tolerances applicable to aluminum alloy drawn tubing ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" applies only to the higher figure of the specified range.
Standard
TOLERANCES, METRIC Aluminum Alloy Drawn Tubing
2002-07-23
MAM2203
This specification covers established metric manufacturing tolerances applicable to aluminum alloy drawn tubing ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" applies only to the higher figure of the specified range.
Standard
CABIN CONNECTORS AND CABLES PART 2 SPECIFICATION OF CONNECTORS, CONTACTS, AND BACKSHELLS
2018-11-28
CURRENT
ARINC800P2-1
This specification describes the general connectors, contacts, and backshells in their shape and characteristic for cabin systems for commercial aircrafts. ARINC 600, ARINC 404, and ARINC 801 connector specifications are published as independent standards.
