Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Ship Systems and Equipment—Part Standard for Studs—Continuous and Double End (Inch Series)

2009-05-04
CURRENT
J2271_200905
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) b Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) Different thread forms on each end are permissible. c Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches) UNRC threads (1/4 through 4 inches) UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) 8UNR threads (1-1/8 through 4 Inches)
Standard

Ball Joints

2012-10-15
CURRENT
J490_201210
This SAE Standard covers the general and dimensional data for various types of ball joints with inch threads commonly used on control linkages in automotive, marine, and construction and industrial equipment applications. Inasmuch as the load carrying and wear capabilities of ball joints vary considerably with their design and fabrication, it is suggested that the manufacturers be consulted in regard to these features and for recommendations relating to application of the different types and styles available. The inclusion of dimensional data in this standard is not intended to imply that all the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning availability of stock production parts.
Standard

Dual Dimensioning Engineering Drawings

1999-05-01
CURRENT
J390_199905
This document covers a dual dimensioning practice that provides both U.S. customary inch-pound units and SI metric units for all dimensions on the field of the drawing. The scope does not include the various methods by which computer programs are used for dual dimensioning. In one method that has had some usage, drawings are dimensioned in SI (metric) units, with conversions to U.S. customary inch-pound units provided in a computer-generated chart on the drawing.
Standard

ROAD VEHICLES—HIGH PRESSURE FUEL INJECTION PIPE END—CONNECTIONS WITH 60 DEGREE FEMALE CONE

1988-10-01
HISTORICAL
J1949_198810
This SAE Standard specifies the dimensional requirements for the assembly of high-pressure pipe connections for compression-ignition (diesel) engine fuel injection equipment. It applies to 60 degrees female cones with external threaded connectors types 1 and 2 (see Figures 1, 2, and 3), and to the internal threaded tube nuts and male cone type end assembly (see Figure 4) of high-pressure pipe connections for tubes with diameters up to 12 mm inclusive.
Standard

Metric Ball Joints

2012-10-15
CURRENT
J2213_201210
This SAE Standard covers the general and dimensional data for industrial quality ball joints commonly used on control linkages in metric automotive, marine, construction, and industrial equipment applications.
Standard

TEST PROCEDURES FOR AUTOMOTIVE STRUCTURAL COMPOSITE MATERIALS

1995-12-01
HISTORICAL
J2253_199512
This SAE Standard is intended to serve as a guide for the collection of physical, mechanical, and thermal properties of fiber-reinforced polymer composite materials for automotive structural applications. This document attempts to utilize test methods applicable to the widest range of structural materials and processes without compromising the integrity of the data being sought. A summary of the material characterization is shown in Section 15.
Standard

Test Procedures for Automotive Structural Composite Materials

2017-07-12
CURRENT
J2253_201707
This SAE Standard is intended to serve as a guide for the collection of physical, mechanical, and thermal properties of fiber-reinforced polymer composite materials for automotive structural applications. This document attempts to utilize test methods applicable to the widest range of structural materials and processes without compromising the integrity of the data being sought. A summary of the material characterization is shown in Section 15.
Standard

Connections for Fluid Power and General Use-Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing Part 1: Port With O-Ring Seal in Truncated Housing

1991-12-01
HISTORICAL
J2244/1_199112
This part of SAE J2244 specifies dimensions for fluid power metric ports for use with adjustable and nonadjustable stud ends shown in SAE J2244/2. Ports in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications.
X