Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

ELECTROMAGNETIC TESTING BY EDDY CURRENT METHODS

1991-03-01
HISTORICAL
J425_199103
The purpose of this SAE Information Report is to provide general information relative to the nature and use of eddy current techniques for nondestructive testing. The document is not intended to provide detailed technical information but to serve as an introduction to the principles and capabilities of eddy current testing, and as a guide to more extensive references listed in Section 2.
Standard

Split Type Bushings – Design and Application

2011-06-13
CURRENT
J835_201106
This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques, and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.
Standard

Socket Wrenches, Hand (Metric)

2013-02-10
CURRENT
MA4534A
This SAE Aerospace Standard covers high strength commercial sockets and universal sockets which possess the strength, clearances, and internal wrenching design so configured that, when mated with hexagon (6 point) fasteners, they shall transmit torque to the fastener without bearing on the outer 5% of the fastener’s wrenching points. This document provides additional requirements beyond ANSI B107.5 appropriate for aerospace use. Inclusion of dimensional data in this document is not intended to imply all of the products described therein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

TOOL AND DIE STEELS

1970-05-01
HISTORICAL
J438_197005
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers.
Standard

Tool and Die Steels

2018-01-09
CURRENT
J438_201801
This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers.
Standard

ELECTROPLATING AND RELATED FINISHES

1985-02-01
CURRENT
J474_198502
Electroplating is a process whereby an object is coated with one or more relatively thin, tightly adherent layers of one or more metals. It is accomplished by placing the object to be coated on a plating rack or a fixture, or in a basket or in a rotating container in such a manner that a suitable current may flow through it, and then immersing it in a series of solutions and rinses in planned sequence. The advantage to be gained by electroplating may be considerable; broadly speaking, the process is used when it is desired to endow the basis material (selected for cost, material conservation, and physical property reasons) with surface properties it does not possess. It should be noted that although electroplating is the most widely used process for applying metals to a substrate, they may also be applied by spraying, vacuum deposition, cladding, hot dipping, chemical reduction, mechanical plating, etc.
Standard

Liquid Penetrant Test Methods

1983-06-01
HISTORICAL
J426_198306
The scope of this SAE Information Report is to supply the user with sufficient information so that he may decide whether liquid penetrant test methods apply to his particular inspection problem. Detailed technical information can be obtained by referring to Section 2.
Standard

Liquid Penetrant Test Methods

1988-12-01
HISTORICAL
J426_198812
The scope of this SAE Information Report is to supply the user with sufficient information so that he may decide whether liquid penetrant test methods apply to his particular inspection problem. Detailed technical information can be obtained by referring to Section 2.
Standard

New Steel Designation System for Wrought or Rolled Steel

2005-07-20
CURRENT
J402_200507
This SAE Standard describes a new alphanumeric designation system for wrought steel used to designate wrought ferrous materials, identify chemical composition, and any other requirements listed in SAE Standards and Recommended Practices. The previous SAE steel designation coding system consisted of four or five numbers used to designate standard carbon and alloy steels specified to chemical composition ranges. Using SAE 1035 as an example, the 35 represents the nominal weight % carbon content for the grade. Using SAE 52100 as an example, the 100 represents the nominal weight % carbon content. The first two numbers of this four or five number series are used to designate the steel grade carbon or alloy system with variations in elements other than carbon. These are described in Table 1. In addition to the standard four or five number steel designation above, a letter was sometimes added to the grade code to denote a non-standard specific element being added to the standard grade.
Standard

ANODIZED ALUMINUM AUTOMOTIVE PARTS

1985-02-01
CURRENT
J399_198502
Automotive parts can be fabricated from either coiled sheet, flat sheet or extruded shapes. Alloy selection is governed by finish requirements, forming characteristics, and mechanical properties. Bright anodizing alloys 5657 and 52521 sheet provide a high luster and are preferred for trim which can be formed from an intermediate temper, such as H25. Bright anodizing alloy 5457 is used for parts which require high elongation and a fully annealed ("0") temper. Alloy 6463 is a medium strength bright anodizing extrusion alloy; Alloy X7016 is a high strength bright anodizing extrusion alloy primarily suited for bumper applications. To satisfy anti-glare requirements for certain trim applications, sheet alloy 5205 and extrusion alloy 6063 are capable of providing the desired low-gloss anodized finish.
Standard

Fluid for Passenger Car Type Automatic Transmissions

2000-02-22
CURRENT
J311_200002
This SAE Information Report details some of the equipment and procedures used to measure critical characteristics of automatic transmission fluid (ATF) used in current automatic transmissions. It is intended to assist those concerned with the design of transmission components, and with the selection and marketing of automatic transmission fluids for the use in passenger car and light-duty truck automatic transmissions. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automatic transmission fluids.
Standard

Measuring Properties of Li-Battery Electrolyte

2015-02-03
CURRENT
J3042_201502
This SAE RP provides a set of test methods and practices for the characterization of the properties of Li-battery electrolyte. It is not within the scope of this document to establish criteria for the test results, as this is usually established between the vendor and customer.
Standard

Categorization and Properties of SAE Cold Rolled Strip Steels

2015-04-28
CURRENT
J2392_201504
This SAE recommended practice defines and establishes tolerances and attributes of cold rolled strip steels. Differences between cold rolled strip and cold rolled sheet products are discussed so that process designers can make informed material selection decisions.
Standard

Classification System for Thermoplastic Elastomers

2005-10-10
HISTORICAL
J2558_200510
This SAE Standard provides a system for specifying significant material properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications. NOTE 1—For the purposes of this document a TPE is defined as a polymeric material that, without further chemical modifications, is capable of recovering from deformations quickly and forcibly and is also capable of being repeatedly softened by heating and hardened by cooling within a temperature range characteristic of the material. NOTE 2—When the TPE product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance to establish the appropriate properties, test methods, and specification test limits.
X