Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

xEV Labels to Assist First and Second Responders, and Others

2017-03-02
CURRENT
J3108_201703
This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.
Standard

Measuring Properties of Li-Battery Electrolyte

2015-02-03
CURRENT
J3042_201502
This SAE RP provides a set of test methods and practices for the characterization of the properties of Li-battery electrolyte. It is not within the scope of this document to establish criteria for the test results, as this is usually established between the vendor and customer.
Standard

Selection of Transmission Media

2000-02-23
CURRENT
J2056/3_200002
This SAE Information Report studies the present transmission media axioms and takes a fresh look at the Class C transmission medium requirements and also the possibilities and limitations of using a twisted pair as the transmission medium. The choice of transmission medium is a large determining factor in choosing a Class C scheme.
Standard

Jump Start Connections for 42 Volt Electrical Systems

2011-02-18
CURRENT
J2651_201102
This SAE Recommended Practice defines test methods and general requirements at all phases of development, production, and field analysis of electrical terminals (including sense pins), connectors, and components that constitute the jump-start connection for road vehicles having 42 V (nominal) electrical systems. The 42 V jump start connector is always remote from the vehicle battery and may take the form of an in-line or Header Connection, either of which is in an accessible location for attachment of a jumper cable from an assist vehicle or battery charger. WARNING—The Jump Start Connector requires environmental protection. This specification assumes that such protection is in place and remains effective for the life of the vehicle. The level of protection depends on the vehicle packaging environment and duty cycle. Appendix B of this document contains the physical specification for the Jump Start Connector.
Standard

Jump Start Connections for 42 Volt Electrical Systems

2005-03-16
HISTORICAL
J2651_200503
This SAE Standard defines test methods and general requirements at all phases of development, production, and field analysis of electrical terminals (including sense pins), connectors, and components that constitute the jump-start connection for road vehicles having 42 V (nominal) electrical systems. The 42 V jump start connector is always remote from the vehicle battery and may take the form of an in-line or Header Connection, either of which is in an accessible location for attachment of a jumper cable from an assist vehicle or battery charger. WARNING--The Jump Start Connector requires environmental protection. This specification assumes that such protection is in place and remains effective for the life of the vehicle. The level of protection depends on the vehicle packaging environment and duty cycle. Appendix B of this document contains the physical specification for the Jump Start Connector.
Standard

Vehicle System Voltage—Initial Recommendations

1999-06-04
CURRENT
J2232_199906
This SAE Information Report is a summary of the initial recommendations of the SAE committee on Dual/Higher Voltage Vehicle Electrical Systems regarding the application of higher voltages in vehicle systems. This document does not attempt to address the technical merits of specific voltages or electrical system architectures.
Standard

Distributed Lighting Systems (DLS)

2011-02-24
CURRENT
J2282_201102
This SAE Recommended Practice applies to motor vehicle Distributed Lighting Systems (DLS) which use light generated by remote sources. It provides test methods, requirements, and guidelines applicable to these systems. This document is intended to be a guide to standard practice and is subject to change dependent upon additional experience and technical advances. This document covers Headlamp, Fog lamp, Auxiliary lamp, plus Signal and Marking lamp functions.
White Paper

Innovative Assembly Systems for the Aerospace Industry

2017-10-31
WP-0004
The aerospace industry is facing new challenges to meet burgeoning customer demand. An unprecedented number of orders for commercial aircraft is forcing aerospace manufacturing to make gains in efficiency throughout aircraft production and operation. However, current manufacturing systems are using technologies and production methods unsuited to a future dynamic market. To ensure its profitability, the aerospace industry must seize the opportunity to innovate and readdress approaches to manufacturing. This whitepaper looks at four advanced manufacturing (AM) solutions designed to improve assembly process efficiency, automation, and accuracy.
Video

A Quantitative Risk Analysis for AeroMACS Network Security in SESAR

2012-03-16
The growing need for an efficient worldwide airspace system management, generated by an increasing traffic load, requires new capabilities for air-ground data communication technologies. In order to cope with these requirements, the Federal Aviation Administration (FAA), EUROCONTROL, and the International Civil Aviation Organization (ICAO) have jointly made specific recommendations for candidate technologies for the airport surface communication network. In the SESAR project, the Aeronautical Mobile Airport Communication System (AeroMACS) technology is being developed in such a way to provide next generation broadband and wireless data communications for airport surface applications (i.e. Air Traffic Control ? ATC, Airline Operational Communications ? AOC, and surface vehicles services).
Video

Development of a Hybrid Control Strategy for an Advanced Parallel HEV Powertrain with Two Electrical Axles

2012-05-29
This paper proposes a current limits distribution control strategy for a parallel hybrid electric vehicle (parallel HEV) which includes an advanced powertrain concept with two electrical driving axles. One of the difficulties of an HEV powertrain with two electrical driving axles is the ability to distribute the electrical current of one high voltage battery appropriately to the two independent electrical motors. Depending on the vehicle driving condition (i.e., car maneuver) or the maximization of the entire efficiency chain of the system, a suitable control strategy is necessary. We propose an input-output feedback linearization strategy to cope with the nonlinear system subject to input constraints. This approach needs an external, state dependent saturation element, which translates the state dependent control input saturation to the new feedback linearizing input and therefore preserves the properties of the differential geometric framework.
Video

Tailored Conversion Coatings for Enhanced Adhesion to Metal

2012-03-21
The use of silane chemistries tailored to promote the adhesion of performance and appearance coatings to metal substrates are requiring new methodologies for measuring, approving, and implementing on commercial aircraft. Engineering performance, lean manufacturing, environmental and employee safety considerations are driving the commercial aerospace industry to replace long standing conversion coating materials and processes. Tailored silane chemistries such as Boegel are being considered for many of these applications. Silanes work by reacting with metal oxides providing a strong covalent bond, cross linking to form a tough barrier and have an organic functional group tailored to react with the specific resin system in the subsequent coating. Traditionally conversion coatings such as anodize and chromate conversion coating performance is validated based on meeting standalone requirements.
X