Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Test Procedures for Evaluating Bolt-Load Retention of Magnesium Alloy

2018-11-02
WIP
USCAR35-1
1.1 A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications. 1.2 The test procedures provides guidance in the following areas: (a) BLR sample and test fixture, (b) test fastener, washer and nut, (c) bolt-load measurement and data acquisition, (d) heating device, (e) initial loading, (f) baseline test, and (g) instrumentation of strain gages and calibration (see Appendix B).
Standard

SAE MANUAL ON BLAST CLEANING

1968-06-01
CURRENT
J792A_196806
Blast cleaning may be defined as a secondary manufacturing process in which a suitable stream of solid particles is propelled with sufficient velocity against a work surface to cause a cleaning or abrading action when it comes in contact with the workpiece. As indicated in the definition, blast cleaning may be employed for a variety of purposes. Ordinarily, it is considered as a method for removing sand from castings, burrs or scale from forgings, mill products, or heat treated parts; to promote machinability, and to minimize the possibility of interference in actual operation. In addition to this use, blast cleaning also produces an excellent surface for industrial coatings. All these objectives are often accomplished in the one operation.
Standard

Ship Systems and Equipment—Part Standard for Studs—Continuous and Double End (Inch Series)

2009-05-04
CURRENT
J2271_200905
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) b Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) Different thread forms on each end are permissible. c Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches) UNRC threads (1/4 through 4 inches) UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) 8UNR threads (1-1/8 through 4 Inches)
Standard

TEST PROCEDURES FOR EVALUATING BOLT-LOAD RETENTION OF MAGNESIUM ALLOYS

2007-10-08
CURRENT
USCAR35
A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications.
Standard

Wrenches, Box and Open End Combination Twelve Point, High Strength, Thin Wall, Metric

2013-02-10
CURRENT
MA4535A
This SAE Metric Aerospace Standard (MA) provides dimensional, performance, testing and other requirements for high strength, thin wall, double head box and combination wrenches which possess an internal wrenching design so configured that, when mated with hexagon (6 point) fasteners, they shall transmit torque to the fastener without bearing on the apex of the fastener’s wrenching points. This standard provides additional requirements beyond ANSI B107.9 appropriate for aerospace use. Inclusion of dimensional data in this document is not intended to imply all of the products described therein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

Socket Wrenches, Hand (Metric)

2013-02-10
CURRENT
MA4534A
This SAE Aerospace Standard covers high strength commercial sockets and universal sockets which possess the strength, clearances, and internal wrenching design so configured that, when mated with hexagon (6 point) fasteners, they shall transmit torque to the fastener without bearing on the outer 5% of the fastener’s wrenching points. This document provides additional requirements beyond ANSI B107.5 appropriate for aerospace use. Inclusion of dimensional data in this document is not intended to imply all of the products described therein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

Leaf Springs for Motor Vehicle Suspension - Made to Customary U.S. Units

2016-04-05
CURRENT
J510_201604
NOTE—For leaf springs made to metric units, see SAE J1123. This SAE Standard is limited to concise specifications promoting an adequate understanding between spring maker and spring user on all practical requirements in the finished spring. The basic concepts for the spring design and for many of the details have been fully addressed in HS-J788, SAE Information Report, Manual on Design and Application of Leaf Springs, which is available from SAE Headquarters.
Standard

LEAF SPRINGS FOR MOTOR VEHICLE SUSPENSION—MADE TO CUSTOMARY U.S. UNITS

1992-11-01
HISTORICAL
J510_199211
NOTE—For leaf springs made to metric units, see SAE J1123. This SAE Standard is limited to concise specifications promoting an adequate understanding between spring maker and spring user on all practical requirements in the finished spring. The basic concepts for the spring design and for many of the details have been fully addressed in HS-J788, SAE Information Report, Manual on Design and Application of Leaf Springs, which is available from SAE Headquarters.
Standard

Diesel Engines—Steel Tubes for High-Pressure Fuel Injection Pipes (Tubing)

2002-10-25
HISTORICAL
J1958_200210
This SAE Standard specifies dimensions and requirements for single-wall steel tubing intended for use as high-pressure fuel injection pipes on a wide range of engines (Class A), and for fuel injection pump testing (Class B, Reference SAE J1418). Tubing shall be cold drawn, annealed or normalized, seamless tubing suitable for cold swaging, cold upsetting, and cold bending.
X