Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Braking Performance - Asphalt Pavers

2012-09-12
HISTORICAL
J2118_201209
This SAE Standard specifies brake system performance and test criteria to enable uniform evaluation of the braking capability of self-propelled, rubber-tired and tracked asphalt pavers. Service, secondary, and parking brakes are included.
Standard

Braking Performance - Asphalt Pavers

2018-10-04
CURRENT
J2118_201810
This SAE Standard specifies brake system performance and test criteria to enable uniform evaluation of the braking capability of self-propelled, rubber-tired and tracked asphalt pavers. Service, secondary, and parking brakes are included.
Video

SAE Eye on Engineering: Ford's new steel-bodied Ranger

2018-11-08
Today, ford motor company begins U.S. production of its 2019 Ranger, the company's first midsize pickup. In this episode of SAE Eye on Engineering, Editor-in-Chief Lindsay Brooke looks at the new steel-bodied Ranger. SAE Eye on Engineering also airs Monday mornings on WJR 760 AM Detroit's Paul W. Smith Show.
Standard

Acceleration Factors

2014-09-12
CURRENT
SSB1_003A
This document is an annex to EIA Engineering Bulletin SSB-1, Guidelines for Using Plastic Encapsulated Microcircuits and Semiconductors in Military, Aerospace and Other Rugged Applications (the latest revision). This document provides reference information concerning acceleration factors commonly used by device manufacturers to model failure rates in conjunction with statistical reliability monitoring. These acceleration factors are frequently used by OEMs in conjunction with physics of failure reliability analysis to assess the suitability of plastic encapsulated microcircuits and semiconductors for specific end use applications.
Standard

ELECTROMAGNETIC TESTING BY EDDY CURRENT METHODS

1991-03-01
HISTORICAL
J425_199103
The purpose of this SAE Information Report is to provide general information relative to the nature and use of eddy current techniques for nondestructive testing. The document is not intended to provide detailed technical information but to serve as an introduction to the principles and capabilities of eddy current testing, and as a guide to more extensive references listed in Section 2.
Standard

Lubricating Oils, Aircraft Piston Engine (Non-Dispersant Mineral Oil)

2011-08-22
CURRENT
J1966_201108
This SAE Standard establishes the requirements for nondispersant, mineral lubricating oils to be used in four-stroke cycle piston aircraft engines. This document covers the same lubricating oil requirements as the former military specification MIL-L-6082. Users should consult their airframe or engine manufacturers manuals for the latest listing of acceptable lubricants.
Standard

Test Procedures for Evaluating Bolt-Load Retention of Magnesium Alloy

2018-11-02
WIP
USCAR35-1
1.1 A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications. 1.2 The test procedures provides guidance in the following areas: (a) BLR sample and test fixture, (b) test fastener, washer and nut, (c) bolt-load measurement and data acquisition, (d) heating device, (e) initial loading, (f) baseline test, and (g) instrumentation of strain gages and calibration (see Appendix B).
Standard

Air Dryer Test Procedure

2012-11-09
CURRENT
J2384_201211
This SAE Recommended Practice establishes uniform Test Procedures for desiccant Air Dryers used in vehicles with compressed air systems per SAE J2383. Continuous flow desiccant Air Dryers are excluded from the scope of this document.
Standard

SAE MANUAL ON BLAST CLEANING

1968-06-01
CURRENT
J792A_196806
Blast cleaning may be defined as a secondary manufacturing process in which a suitable stream of solid particles is propelled with sufficient velocity against a work surface to cause a cleaning or abrading action when it comes in contact with the workpiece. As indicated in the definition, blast cleaning may be employed for a variety of purposes. Ordinarily, it is considered as a method for removing sand from castings, burrs or scale from forgings, mill products, or heat treated parts; to promote machinability, and to minimize the possibility of interference in actual operation. In addition to this use, blast cleaning also produces an excellent surface for industrial coatings. All these objectives are often accomplished in the one operation.
Standard

Brake Master Cylinder Plastic Reservoir Assembly for Road Vehicles

1994-06-01
HISTORICAL
J2053_199406
This SAE Recommended Practice specifies the performance test procedures and requirements of a plastic reservoir assembly suitable for use on a hydraulic brake master cylinder (reference SAE J1153). Intended usage is for on-road vehicles using brake fluid conforming to fMVSS-116 (DOT 3), and SAE J1703 specifications. This document includes the cap.cover and diaphragm as integral parts of the reservoir assembly. The fluid level sensor (FLS) is also included as an integral part of the assembly. However, additional FLS standards and/or requirements are applicable and necessary which are not covered in this document. This document is intended to provide a recommended practice and minimum performance requirements of current established designs on those reservoir assemblies generally used by individual manufacturers which have demonstrated satisfactory field performance. This document is applicable to new reservoir assemblies for commercial or aftermarket production.
Standard

Nomenclature--Industrial and Agricultural Mowers

1986-05-01
HISTORICAL
J990_198605
This Standard provides names of many of the major components and parts peculiar to agricultural and industrial rotary, flail and sickle bar type mowers. Illustrations used are not intended to include all existing industrial or agricultural machines, or to be exactly descriptive of any particular machine. They have been picked to describe the principles to be used in applying this standard.
Standard

Crane Boom Hoist Disengaging Device

2017-08-15
WIP
J999
This SAE Standard applies to cranes which are equipped to adjust the boom angle by hoisting and lowering means through rope reeving. The purpose of this standard is to define the function and to stipulate the requirements of an automatic device to prevent raising a variable angle boom above its highest specified angle.
X