Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Braking Performance - Asphalt Pavers

2012-09-12
HISTORICAL
J2118_201209
This SAE Standard specifies brake system performance and test criteria to enable uniform evaluation of the braking capability of self-propelled, rubber-tired and tracked asphalt pavers. Service, secondary, and parking brakes are included.
Standard

Braking Performance - Asphalt Pavers

2018-10-04
CURRENT
J2118_201810
This SAE Standard specifies brake system performance and test criteria to enable uniform evaluation of the braking capability of self-propelled, rubber-tired and tracked asphalt pavers. Service, secondary, and parking brakes are included.
Standard

R134a Refrigerant Charge Determination Test Method

2018-09-11
CURRENT
J3023_201809
The purpose of this document is to establish guidelines for determining the critical R134a refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a refrigerant charge for the HVAC system.
Standard

Acceleration Factors

2014-09-12
CURRENT
SSB1_003A
This document is an annex to EIA Engineering Bulletin SSB-1, Guidelines for Using Plastic Encapsulated Microcircuits and Semiconductors in Military, Aerospace and Other Rugged Applications (the latest revision). This document provides reference information concerning acceleration factors commonly used by device manufacturers to model failure rates in conjunction with statistical reliability monitoring. These acceleration factors are frequently used by OEMs in conjunction with physics of failure reliability analysis to assess the suitability of plastic encapsulated microcircuits and semiconductors for specific end use applications.
Standard

Top Speed Test Procedure for Electric Motorcycles

2014-02-21
CURRENT
J3007_201402
This SAE Recommended Practice incorporates a track-based test procedure that produces a representative value for vehicle top speed when operating on a level paved road with a fully charged battery.
Standard

Nomenclature--Industrial and Agricultural Mowers

1986-05-01
HISTORICAL
J990_198605
This Standard provides names of many of the major components and parts peculiar to agricultural and industrial rotary, flail and sickle bar type mowers. Illustrations used are not intended to include all existing industrial or agricultural machines, or to be exactly descriptive of any particular machine. They have been picked to describe the principles to be used in applying this standard.
Standard

Engine Rotation and Cylinder Numbering

1986-01-01
HISTORICAL
J824_198601
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
Standard

Crane Hoist Line Speed and Power Test Procedure

2017-06-07
CURRENT
J820_201706
This document applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if the load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed. This recommended practice applies to all mechanical, hydraulic, and electric powered hoist mechanisms.
Standard

Crane Hoist Line Speed and Power Test Code

1998-07-01
HISTORICAL
J820_199807
This code applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed.
Standard

Non-Contact Hose Measurement Study 1

2006-01-04
HISTORICAL
J2605_200601
The Hose Measurement Task Force conducted a round-robin study to determine the measuring capability of automotive suppliers and users to simultaneously measure the Inside Diameter (ID), Outside Diameter (OD), Wall Thickness (Wall), and Wall thickness Variation (WV) of hose using a laser-based, non-contact LOTIS QC-20 gauging device. Three (3) companies (all end users) participated in this testing with one of the three companies performing the GR&R calculations presented herein. Based upon the round-robin study this report will detail procedures, test measuring devices, results, and conclusions.
Standard

Push-On Hose and Mating Hose Fittings

2014-06-06
CURRENT
J2552_201406
SAE J2552 provides limited, dimensional and general performance requirements for low pressure, field attachable, push-on hose and their mating hose fittings. The intended application is for fluid and pneumatic power used with petroleum base hydraulic fluids, lube oils, water glycols and air, within the temperature ranges listed in Table 1. The maximum working pressure is 1.7 MPa (see Table 2). For air applications the maximum working pressure is at 0.7 MPa. Hose and hose fittings are manufactured within certain dimensions with tolerance ranges in order to provide the proper gripping and sealing. SAE J2552 hose from one manufacturer may not be compatible with SAE J2552 hose fittings supplied by another manufacturer. It is the responsibility of the fabricator to always follow the manufacturers’ instructions for proper preparation and fabrication of hose assemblies.
Standard

Non-Contact Hose Measurement Study 1

2015-04-21
CURRENT
J2605_201504
The Hose Measurement Task Force conducted a round-robin study to determine the measuring capability of automotive suppliers and users to simultaneously measure the Inside Diameter (ID), Outside Diameter (OD), Wall Thickness (Wall), and Wall thickness Variation (WV) of hose using a laser-based, non-contact LOTIS QC-20 gauging device. Three (3) companies (all end users) participated in this testing with one of the three companies performing the GR&R calculations presented herein. Based upon the round-robin study this report will detail procedures, test measuring devices, results, and conclusions.
Standard

Ship Systems and Equipment—Part Standard for Studs—Continuous and Double End (Inch Series)

2009-05-04
CURRENT
J2271_200905
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) b Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) Different thread forms on each end are permissible. c Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches) UNRC threads (1/4 through 4 inches) UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) 8UNR threads (1-1/8 through 4 Inches)
Standard

Fastener Part Standard - Hexagon Socket, Square Head, and Slotted Headless Set Screws - Inch Dimensioned

2016-11-15
CURRENT
J2656_201611
This SAE Part Standard covers selected inch dimensioned set screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document.
Standard

Optical Imaging Evaluation of Impact Damage Resistance Testing on Exterior Finishes

2011-05-26
CURRENT
J2661_201105
This SAE Recommended Practice covers a procedure for evaluating plastic and multiple-layer coatings exposed to gravelometer testing (as defined in SAE J400) with an optical imaging and analysis system. The intent of the procedure is to detect, count and characterize instances of damage in the coated surface that fracture the top coat layer or penetrate through multiple layers of the coating system. It may be possible to extend this methodology of coating damage evaluation to specimens that have undergone test procedures or exposures that produce similar, discrete damage sites in the coating system. If so applied, evaluation results must be interpreted with respect to the limitations and intent implied by the original evaluation procedure and its associated rating system, if applicable.
X